Mitsubishi Electric AE-200A Bedienungsanleitung

Contents

Safety precautions..............................................................................2

1. Introduction ..................................................................................4

2. Parts to be used ...........................................................................5

3. Apportioned electricity billing function in the BACnet®function....7

3-1. Change timing of the apportioned electricity billing

function objects in the BACnet®function...............................7

4. Apportioned electricity billing function trial run procedure

in the BACnet®function................................................................9

4-1. Entire trial run flow ................................................................9

4-2. BACnet®(checking before a billing trial run) .......................10

4-3. BACnet®(1st run check (after air conditioning unit

continuous operation)..........................................................15

4-4. BACnet®(2nd run check (at least 10 days after the 1st

billing function trial run) .......................................................22

4-5. BACnet®(3rd run check (at least 1 month after the 2nd

billing function trial run) .......................................................22

Air Conditioning Control System

Centralized Controller

AE-200A/AE-50A/EW-50A

AE-200E/AE-50E/EW-50E

Instruction Book

–

BACnet

Apportioned Electricity Billing Function Trial Run

–

Before using the controller,

please read this Instruction

Book carefully to ensure proper

operation.

Retain this manual for future

reference.

BACnet®is a registered

trademark of ASHRAE (American

Society of Heating, Refrigerating

and Air-Conditioning Engineers,

INC.).

WT08246X03

Safety precautions

►Observe these precautions carefully to ensure safety.

►After reading this manual, pass the manual on to the end user to retain for future

reference.

►The user should keep this manual for future reference and refer to it as necessary. This

manual should be made available to those who repair or relocate the units. Make sure

that the manual is passed on to any future air conditioning system user.

: indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

: indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

: addresses practices not related to personal injury, such as product

and/or property damage.

General precautions

Do not install the controller in areas where large amounts of oil, steam, organic solvents,

or corrosive gases (such as ammonia, sulfuric compounds, or acids), or areas where

acidic/alkaline solutions or special chemical sprays are used frequently. These substances

may significantly reduce the performance and corrode the internal parts, resulting in

electric shock, malfunction, smoke, or fire.

To reduce the risk of short circuits, current leakage, electric shock, malfunction, smoke, or

fire, do not wash the controller with water or any other liquid.

To reduce the risk of electric shock, malfunction, smoke, or fire, do not touch the electrical

parts, USB memory, or touch panel with wet fingers.

To reduce the risk of injury or electric shock, before spraying a chemical around the

controller, stop the operation and cover the controller.

To reduce the risk of injury, keep children away while installing, inspecting, or repairing the

controller.

If you notice any abnormality (e.g., burning smell), stop the operation, turn off the

controller, and consult your dealer. Continuing the operation may result in electric shock,

malfunction, or fire.

Properly install all required covers to keep moisture and dust out of the controller. Dust

accumulation and the presence of water may result in electric shock, smoke, or fire.

To reduce the risk of fire or explosion, do not place flammable materials or use flammable

sprays around the controller.

To reduce the risk of electric shock or malfunction, do not touch the touch panel, switches,

or buttons with a sharp object.

To avoid injury from broken glass, do not apply excessive force to the glass parts.

WT08246X03

To reduce the risk of injury, electric shock, or malfunction, avoid contact with the sharp

edges of certain parts.

Consult your dealer for the proper disposal of the controller. Improper disposal will pose a

risk of environmental pollution.

Precautions for relocating or repairing the unit

The controller must be repaired or moved only by qualified personnel. Do not disassemble

or modify the controller. Improper installation or repair may result in injury, electric shock,

or fire.

Additional precautions

To avoid discoloration, do not use benzene, thinner, or chemical rag to clean the controller.

When the controller is heavily soiled, wipe the controller with a well-wrung cloth that has

been soaked in water with mild detergent, and then wipe off with a dry cloth.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play

with the appliance.

Terms used in this manual

- “Centralized Controller AE-200A/AE-200E” is referred to as “AE-200”.

- “Centralized Controller AE-50A/AE-50E” is referred to as “AE-50”.

- “Centralized Controller EW-50A/EW-50E” is referred to as “EW-50”.

WT08246X03

1. Introduction

To use the billing information objects (accumulator objects and trend log objects (excluding Trend Log Room

Temp)) for the BACnet®function in the apportioned electricity billing function of the AE-200/AE-50/EW-50, follow

the procedure in this document, in addition to the procedure described in “7. Billing function trial run” in the

AE-200/AE-50/EW-50 Instruction Book –Apportioned Electricity Billing Function–.

To perform a trial run, you need to obtain this document and the AE-200/AE-50/EW-50 Instruction Book

–Apportioned Electricity Billing Function–.

To use the billing information objects for the BACnet®function, you need to register the “Charge” license with the

AE-200/AE-50/EW-50. For the license registration procedure, refer to the AE-200/AE-50/EW-50 Instruction Book

–Initial Settings–.

Entire flow diagram of initial settings and trial run for the AE-200/AE-50/EW-50 (when using the apportioned

electricity billing function and BACnet®function)

*1 Before performing a trial run for the apportioned electricity billing function (BACnet®), perform a trial run for the air conditioning system

and check that the group settings/interlocked unit settings are correct (the correspondence of the actual air conditioning units/interlocked

units with the group numbers is correct) from the AE-200/AE-50’s LCD or from the Integrated Centralized Control Web.

*2 When using the billing information objects for the BACnet®function, set a single group in a single block when setting the energy

management block. If there are OA processing units registered as interlocked LOSSNAY, register a single OA processing unit in a single

block. (because this operation is required in 4-3-3 “Checking the match with the CSV data (apportioned results) of the AE-200”.

*3 Enable accumulator objects and trend log objects.

*4 Perform a continuous operation for each indoor unit for at least 2 hours before performing the check after 00:00 on the day of the 1st

check (after air conditioning unit continuous operation).

Normal initial settings and trial run

for all AE-200 systems *1

When using the apportioned electricity billing

function only from BACnet®, the settings are not

required.

AE-200 settings

Settings on the Initial Setting Tool

(with apportioned electricity

billing function) *2

Settings

on the Charge Calculation Tool

Initial Settings

for BACnet®function *3

When changing the “Log_interval” property of the

trend log object to 180000 (30 minutes), change it

after performing the initial settings for the BACnet®

function.

Scope covered by this document

The order of this and “Billing function trial run”

may be changed.

To a test with the building management system

BACnet®function trial run

Billing function trial run

Apportioned electricity billing

function (AE-200 system)

trial run

Apportioned electricity

billing function

(BACnet®) trial run *4

Initial settings

for apportioned

electricity billing

function

WT08246X03

2. Parts to be used

Prepare the following when performing a trial run.

Item Qty Remarks

Material

Diagram of air conditioning control

system for building 1 Group configuration, IP address etc.

Apportioned electricity billing function

setting information and metering

device connection information

AE-200/AE-50/EW-50 Instruction

Book –Apportioned Electricity Billing

Function–

1*1

AE-200/AE-50/EW-50 Instruction

Book –BACnet®function– 1*1

AE-200/AE-50/EW-50 Instruction

Book –BACnet®Apportioned

Electricity Billing Function Trial Run–

1 This document

AE-200/AE-50/EW-50 Instruction

Book –BACnet®Trial Run Tool– 1*1

Instruction books for each air

conditioning unit, controller, and

metering device

Equipment,

device

PC *2 1–2 *3

Used for running Microsoft Excel, Initial

Setting Tool, BACnet®Trial Run Tool, and

Integrated Centralized Control Web

Microsoft Excel 1 Microsoft Excel 2007 or later

BACnet®Trial Run Tool 1*1

Initial Setting Tool (with apportioned

electricity billing function) 1*1

USB memory device 1

Used for retrieving CSV data (apportioned

results).

For manufacturers and models of

USB memory devices for which

operation has been verified, refer to the

AE-200/AE-50/EW-50 Instruction Book

–Initial Settings–.

Switching HUB 1–2 *3 Used for connecting a PC.

LAN cable (Category 5 or above

straight cable) 2–4 *3 Used for connecting a PC.

L-shaped driver (hexagonal wrench) 1 Included with AE-200, used for removing or

attaching the AE-200 cover.

General tool such as a driver -

*1 Contact your dealer to obtain this.

*2 For the necessary specifications and other information, refer to the AE-200/AE-50/EW-50 Instruction Book –Apportioned Electricity Billing

Function–, AE-200/AE-50/EW-50 Instruction Book –Initial Settings–, and AE-200/AE-50/EW-50 Instruction Book –BACnet®Trial Run

Tool–.

*3 You just need the minimum number only for a trial run, but the maximum number is more efficient for a combination of the settings and

trial run.

WT08246X03

Connection diagram for a trial run

*1 If a trial run is performed with a single PC, connect it as a trial run PC. Furthermore, if the settings need to be checked or changed, it can

also be used as a setting PC by changing the network connection settings and switching the LAN connection.

Trial run PC *1

(BACnet® Trial Run Tool)

LAN1

M-NET

BACnet®

AE-200

“Charge” license

LAN2 (BACnet®)

LAN1

M-NET

LAN2 (BACnet®)

LAN1

M-NET

Indoor unit,

outdoor unit

LAN2 (BACnet®)

LAN1

M-NET

LAN2 cannot be connected.

LAN2 (BACnet®)

HUB HUB

Indoor unit,

outdoor unit

Indoor unit,

outdoor unit

Indoor unit,

outdoor unit

Setting PC *1

(Initial Setting Tool,

BACnet®Setting

Tool, Integrated

Centralized Control

Web)

LAN1

M-NET cannot be connected.

AE-50/EW-50

“BACnet connection” license

“Charge” license

AE-50/EW-50

“BACnet connection” license

“Charge” license

AE-50/EW-50

“BACnet connection” license

“Charge” license

AE-50/EW-50

“BACnet connection” license

“Charge” license

WT08246X03

3. Apportioned electricity billing function in the

BACnet®function

The apportioned results calculated by the apportioned electricity billing function of the AE-200/AE-50/EW-50

are retrieved from the building management system via BACnet®by using the billing information objects of the

BACnet®function.

3-1. Change timing of the apportioned electricity billing function objects in

the BACnet®function

The billing information objects of the BACnet®function change according to the following specifications and

timing.

•The apportioned result (cumulative value) is calculated every 30 minutes from the electric energy

consumption for the period between XX:00 and XX:30 minutes or between XX:30 and XX:00 minutes every

hour and the cumulative value is stored. (The apportioned result (cumulative value) is a value for internal

calculation and cannot be referred to from the outside.)

•The electric energy value stored in the accumulator object is updated at XX:15 and XX:45 minutes every

hour.

•The update of the electric energy value stored in the accumulator object is performed by adding the

difference between the last two apportioned results (cumulative values) to the value in the “Present_Value”

property.

(For the “PI controller Electric Energy 1–4” or “Pulse Input Electric Energy 1–4” objects, the update is

performed by adding the difference between the last two measurement results to the value in the “Present_

Value” property.)

•The trend log object is updated at each interval set in the “Log_interval” property from the reference point

(1970/1/1 00:00).

In the test run procedure explained in this manual, the “Log_interval” property needs to be set to 180000 (1800

seconds = 30 minutes).

(For the procedure for setting the “Log_interval” property of the trend log object, refer to the AE-200/AE-50/

EW-50 Instruction Book –BACnet®Trial Run Tool–. Furthermore, the “Log_interval” property needs to be

specified in 1/100 seconds. The initial value of the “Log_interval” property is 8640000 (24 hours) in versions

earlier than AE-200/AE-50/EW-50 Version 7.45, and 180000 (30 minutes) in AE-200/AE-50/EW-50 Version

7.45 and later.)

When comparing the display value of the metering device or the [Monitor/Operation] - [Measurement] display of

the AE-200 with the billing information object in the BACnet ®function, or when checking the billing information

object after changing the settings, make sure to consider the time lag in order not to refer to the data before the

change.

WT08246X03

The following shows an operation example of the apportioned electricity billing function of the AE-200 (when it is

started at 10:00).

The example assumes that there are no apportioned results in the past (at the default settings) and that 180000

(1800 seconds = 30 minutes) is set in the “Log_interval” property.

The time when the apportioned result is stored for the first time is indicated by bold characters.

Accumulator and trend log object update timing

Time

10:00

10:15

10:30

10:45

11:00

11:15

11:30

11:45

12:00

Apportioned calculation

(cumulative value)

<> indicates the cumulation

range.

(Unit [0.1 kWh])

“Present_Value” of the

accumulator object

(Unit [0.1 kWh])

”Log_Buffer” of the trend

log object

Apportioned result [1]

(Example: 20)

<10:00–10:30>

Update (+ 0) = 0

(0 because of the

shortage of calculation target)

Store (0)

Apportioned result [2]

(Example: 50)

<10:00–11:00>

Update (+ 0) = 0

(0 because of the

shortage of calculation target)

Store (0)

Apportioned result [3]

(Example: 90)

<10:00–11:30>

Apportioned result [4]

<10:00–12:00>

Update (+ Apportioned result

[3] - [2])

= 30 + (90 - 50) = 70

Store (Apportioned result

[3] - [1])

(70)

Store (Apportioned result

[2] - [1])

(30)

Update (+ Apportioned result

[2] - [1])

= 0 + (50 - 20) = 30

WT08246X03

4. Apportioned electricity billing function trial run

procedure in the BACnet®function

4-1. Entire trial run flow

Perform a trial run according to the following procedure.

Check timing Step

Procedure explained in the

AE-200/AE-50/EW-50 Instruction Book

–Apportioned Electricity Billing Function–

Procedure explained in this manual

Before billing function

trial run

1 7-1. “Flow of the billing function trial run” ←

2 4-2-1 “BACnet®metered value correction”

37-2. “Checking the billing function settings

(check before billing function trial run)” ←

4 7-2-1. “Billing-related item sheet” ←

5 7-2-2. “Unit-related item sheet” ←

6 7-2-3. “Entering the electric energy” ←

7 4-2-2 “Billing-related item sheet (BACnet®)”

8 4-2-3 “Unit-related item sheet (BACnet®)”

1st run check (after

air conditioning unit

continuous operation

for more than 2

hours)

Run each indoor unit continuously for at least 2 hours as explained in the AE-200/AE-50/

EW-50 Instruction Book –Apportioned Electricity Billing Function–

At 00:00 or later on the day of the 1st run check (after air conditioning unit continuous

operation), run each indoor unit continuously for at least 2 hours.

9 7-3. “Billing function trial run checks” ←

7-3-1. “1st run check (after air

conditioning unit continuous operation)”

[1] “Billing-related item sheet”

←

11 4-3-1 “Billing-related item sheet (BACnet®)”

7-3-1. “1st run check (after air

conditioning unit continuous operation)”

[2] “Unit-related item sheet”

←

13 4-3-2 “Unit-related item sheet (BACnet®)”

14 4-3-3 “Checking the match with the CSV data

(apportioned results) of the AE-200”

2nd run check

(at least 10 days

after the 1st billing

function trial run)

15 7-3-2. “2nd run check (at least 10 days

after 1st billing function trial run)” ←

16 4-4 “BACnet®(2nd run check (at least 10

days after the 1st billing function trial run)”

3rd run check (at

least 1 month after

the 2nd billing

function trial run)

17 7-3-3. “3rd run check (at least 1 month

after the 2nd billing function trial run)” ←

18 4-5 “BACnet®(3rd run check (at least 1 month

after the 2nd billing function trial run)”

19 7-4. “Final checks” ←

20 7-4-1. “Final checks for the operation

settings” ←

21 7-4-2. “Final report” ←

WT08246X03

4-2. BACnet®(checking before a billing trial run)

Before performing the procedure in this section, make sure to perform the procedure described in “7-1. Flow

of the billing function trial run” in the AE-200/AE-50/EW-50 Instruction Book –Apportioned Electricity Billing

Function–.

4-2-1. BACnet®metered value correction

Check that the metering device values used for the apportioned electricity billing function and the “Present_

Value” property values of the BACnet®objects “PI controller Electric Energy 1–4” (AC_41mm40–43: mm = PI

controller address (01–50)) or “Pulse Input Electric Energy 1–4” (AC_410040–43) match. If they do not match,

change the “Present_Value” property values.

However, as described in 3-1 “Change timing of the apportioned electricity billing function objects in the BACnet®

function”, there is a time lag until the “Present_Value” property values are reflected so they do not match the

metering device display values at the same time (which does not matter for the apportion calculation).

Furthermore, the apportion calculation results are not influenced by changes in the “Present_Value”

property values of “PI controller Electric Energy 1–4” (AC_41mm40–43) or “Pulse Input Electric Energy 1–4”

(AC_410040–43).

Procedures

1. After starting the AE-200, record the display value of the metering device at the time when the internal clock

of the AE-200 shows the XX:00 or XX:30 minutes of every hour.

2. Use BACnet®Trial Run Tool and enter the electric energy value in a unit of 0.1 [kWh] (for example, 1234 for

123.4 kWh) recorded at the time when 20 to 45 minutes have passed since step 1 (for example, between

10:20 and 10:45 if the value was recorded at 10:00, or between 10:50 and 11:15 if the value was recorded

at 10:30) in the “Value_Set” property for the object corresponding to the metering device.

(If you failed to enter the value during the entry period, perform the procedure again from step 1.)

3. Immediately read the “Present_Value” property value of the same object and make sure that the entered

value is reflected.

The following shows the objects corresponding to the metering device.

Connect metering device to Object name Object ID

PI controller

Ch.1 PI controller Electric Energy 1 AC_41mm40

Ch.2 PI controller Electric Energy 2 AC_41mm41

Ch.3 PI controller Electric Energy 3 AC_41mm42

Ch.4 PI controller Electric Energy 4 AC_41mm43

AE-50/EW-50

Pulse Input

Ch.1 Pulse Input Electric Energy 1 AC_410040

Ch.2 Pulse Input Electric Energy 2 AC_410041

Ch.3 Pulse Input Electric Energy 3 AC_410042

Ch.4 Pulse Input Electric Energy 4 AC_410043

* mm: PI controller address (01–50)

Note

For how to operate BACnet®Trial Run Tool, refer to the AE-200/AE-50/EW-50 Instruction Book –BACnet®

Trial Run Tool–.

Andere Handbücher für AE-200A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Steuerungssystem Handbücher

Mitsubishi Electric

Mitsubishi Electric TC-24A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric C80 Series Einrichtungshandbuch

Mitsubishi Electric

Mitsubishi Electric CB10 ME Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AL2-EEPROM-2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MAC-588IF-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAR-CT01MAA-SB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Installationsanleitung

Mitsubishi Electric

Mitsubishi Electric MCCH1 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric TW-50A Kurzanleitung

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAAU Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LMAP02-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS 600 Series Gebrauchsanweisung

Mitsubishi Electric

Mitsubishi Electric MDS-E Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AG-150A-A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT34STA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric GB-50ADA-J Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J2S Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric C80 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric C70 Benutzerhandbuch

Mitsubishi Electric

Mitsubishi Electric BAC-HD150 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS C6 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MJ-310E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric E70 Series Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung