Mitsubishi Electric MCCH1 Bedienungsanleitung

69-2428EFS-03

Suwanee, GA 30024

US Patent No. D579,798; D592,081 and other patents

The three diamond logo is a registered trademark

of Mitsubishi Electric Corporation

Wireless Accessories Installation Manual

MCCH1 Portable Central Controller

MOS1 Outdoor Air Sensor

Français : voir la page 7 •Español: vea la página 13

Installation procedure

Install batteries in wireless devices ...............................................Page 2

Link devices to wireless network............................................. Pages 2-3

Mount outdoor sensor ....................................................................Page 4

To replace system components, if needed, see page 5.

If there is more than one Wireless Receiver, Equipment Interface Module (EIM)

or zone panel:

Wireless devices must be linked separately to each Wireless Receiver, EIM or zone

panel.

Wireless receiver

Wireless

outdoor

air sensor

Portable

central

controller

M32309

Remote controller

Installation Guide - Wireless Accessories

69-2428EFS—03 2

1Install batteries in wireless devices

Make sure batteries are inserted properly (see polarity marks on illustrations

below).

2Link devices to wireless network

M28476

M28475

Portable central controller Outdoor air sensor

Install 3 fresh

AA batteries

Install 2 fresh AA

lithium batteries

Flashing status light times out after 15

minutes of inactivity. Press CONNECT

again if necessary.

1Remove cover from wireless receiver.

2Verify POWER light is solid green.

3Press and release the CONNECT button.

4If CONNECT light does not flash, another receiver

or RedLINK wireless adapter may be in wireless

setup mode. Exit wireless setup at the other

device.

Français : voir la page 7 • Español: vea la página 13

3 69-2428EFS—03

Link Portable central controller to RedLINK™ network

Link outdoor sensor to RedLINK™ network

CONNECT

WIRELESS SETUP

M28481

M28483

NOYES

CONNECT MORE?

M28482

1Make sure the CONNECT light on the wireless

receiver is flashing.

2Press CONNECT at the Portable central

controller. There will be a short delay as the

Portable central controller seeks a signal from

the wireless network.

3When the screen displays "Connected," press

DONE.

4Press NO at the next screen to save and exit.

(Or press YES and repeat steps 1-4 to link

another receiver.)

1Make sure the CONNECT light on the wireless

receiver is flashing.

2Press and release the CONNECT button on the

back of the sensor.

3Check remote controller to verify that the

outdoor sensor is working. After about 15

seconds, the remote controller should display

outdoor temperature and humidity.

Press to link

another receiver Press to save

and exit

If E1 appears, see error codes on page 4.

The linking procedure may time out if there is no

keypress within 15 minutes. To begin again, press

and hold the blank space (or arrow, if present)

in the lower right corner of the screen until the

display changes (about 3 seconds).

Press and release

Installation Guide - Wireless Accessories

69-2428EFS—03 4

M28491

M28492

Mount the sensor on a

vertical exterior wall, at

least 6 inches below any

overhang. Choose a location

protected from direct

sunlight.

Place sensor securely

in bracket, facing away

from wall.

3Mount outdoor sensor

Error codes (Portable central controller)

If E1 or E appears, check error code number (right side of screen):

29 You are attempting to connect a Portable central controller to an incompatible

device.

34 Low signal strength. Move Portable central controller to a different location and try

again.

38 Make sure Connect light is flashing and you are 2+ feet away from wireless receiver.

Français : voir la page 7 • Español: vea la página 13

5 69-2428EFS—03

Replacing system components

Portable central controller or outdoor sensor

To replace a Portable central controller or outdoor air sensor, install batteries

in the new component and follow the procedures on pages 2-3 to link it to the

wireless network.

Wireless Receiver, Equipment Interface Module, or Zone Panel

After installing a new wireless receiver, Equipment Interface Module, or zone

panel, you must re-set the Portable central controller to communicate with the

new equipment, as described below.

At the Portable central controller:

1 Press and hold the blank space (or arrow if

present) in the lower right corner of the screen

until the display changes (about 3 seconds).

2 Press REMOVE,then YES to disconnect from old

equipment.

3 Follow the procedure on pages 2-3 to link to new

equipment.

Removing all wireless devices:

1 Press and hold the CONNECT button on the wireless

receiver, Equipment Interface Module, or wireless adapter for 10 seconds.

2 To reconnect, see procedure on pages 2-3.

Installation Guide - Wireless Accessories

69-2428EFS—03 6

Regulatory information

FCC Compliance Statement (Part 15.19) (USA only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1 This device may not cause harmful interference, and

2 This device must accept any interference received, including interference that may cause

undesired operation.

FCC Warning (Part 15.21) (USA only)

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

FCC Interference Statement (Part 15.105 (b)) (USA only)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver

is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Outdoor sensor

TocomplywithFCCandIndustryCanadaRFexposurelimitsforgeneralpopulation/

uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or operating

in conjunction with any other antenna or transmitter.

Portable Central Controller

This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure

limitsforgeneralpopulation/uncontrolledexposure.Thisdevicemustnotbeco-locatedor

operating in conjunction with any other antenna or transmitter.

Section 7.1.3 of RSS-GEN

Operation is subject to the following two conditions:

1 this device may not cause interference, and

2 this device must accept any interference, including interference that may cause

undesired operation of the device.

Section 7.1.2 of RSS-GEN

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of

type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its gain should be so chosen

that the equivalent istropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication.

Brevets US NO. D579,798; D592,081 et autres brevets en instance.

Le logo à trois losanges est une marque déposée de Mitsubishi Electric Corporation

Guide d’installation des

accessoires sans fil

Contrôleur central portable MCCH1

Capteur de température extérieure MOS1

English: see page 1 •Español: vea la página 13

Installation

Insertion des piles dans l’appareil sans fil ....................................Page 8

Relier l’appareil au réseau sans fil........................................... Pages 8-9

Installation du capteur extérieur ..................................................Page 10

Pour remplacer les composants du système au besoin, voir la page 11.

S’il y a plus d’un récepteur sans fil, d’un module d’interface d’équipement

(EIM) ou d’un panneau de zone :

Les appareils sans fil doivent être connectés séparément à chaque récepteur sans fil,

module d’interface d’équipement ou panneau de zone.

Régulateur

central

portatif

MF32309

Régulateur à distance

Récepteur sans fil

Capteur

d’air

extérieur

Guide d’installation - Accessoires sans fil

69-2428EFS—03 8

1Insertion des piles dans l’appareil sans fil

S’assurer que les piles sont correctement insérées (voir les marques de

polarité sur l’illustration de gauche).

2Lier tous les appareils au réseau sans fil

M28476

M28475

Capteur d’air extérieur

Insérer 3 piles

AA neuves

Insérer 2 piles au

lithium AA neuves

Contrôleur central portable

Le voyant de statut clignotant s’éteint

après 15 minutes d’inactivité. Si

nécessaire, appuyer une nouvelle fois

sur CONNECT.

1Retirer le couvercle du récepteur sans fil.

2Vérifier que le voyant POWER est allumé en vert

en continu.

3Appuyer sur le bouton CONNECT et le relâcher.

4Si le voyant CONNECT ne clignote pas, un autre

récepteur ou adaptateur sans fil RedLINK peut

être en mode de configuration sans fil. Faire sortir

l’autre dispositif du mode de configuration sans

fil.

English: see page 1 • Español: vea la página 13

9 69-2428EFS—03

Raccordement du régulateur central portatif au réseau

RedLINK™

Raccordement du capteur d’extérieur au réseau

RedLINK™

CONNECT

WIRELESS SETUP

M28481

M28483

NOYES

CONNECT MORE?

M28482

1S’assurer que le voyant CONNECT clignote sur

le récepteur sans fil.

2Appuyer sur CONNECT sur le régulateur central

portatif. Un court délai a lieu tandis que le

régulateur central portatif cherche un signal

provenant du réseau sans fil.

3Lorsque l’écran affiche « Connected », appuyer

sur DONE (Terminé).

4Appuyer sur NO (Non) sur l’écran suivant pour

enregistrer et quitter. (Ou appuyer sur YES (Oui)

et répéter les étapes 1-4 pour raccorder un

autre récepteur.)

1S’assurer que le voyant CONNECT clignote sur

le récepteur sans fil.

2Appuyer sur le bouton CONNECT au dos du

capteur et le relâcher.

3Vérifier le régulateur à distance pour s’assurer

que le capteur d’extérieur fonctionne. Après

environ 15 secondes, le régulateur à distance

doit afficher la température et l’humidité

extérieures.

Si E1 s’affiche, voir les codes d’erreur page 10.

La procédure de raccordement peut s’arrêter si

aucun bouton n’est pressé pendant 15 minutes.

Pour recommencer, appuyer sur l’espace

vierge (ou la flèche, le cas échéant) dans le

coin inférieur droit de l’écran jusqu’à ce que

l’affichage change (environ 3 secondes).

Appuyer et relâcher

Appuyer pour

raccorder un

autre récepteur

Appuyer pour

enregistrer et

quitter

Guide d’installation - Accessoires sans fil

69-2428EFS—03 10

M28491

M28492

Installer le capteur sur un

mur extérieur à la verticale,

à au moins 6 pouces (15

cm) de tout surplomb.

Choisir un emplacement où

le capteur sera à l’abri des

rayons du soleil.

Fixer fermement le

capteur sur le support,

en mettant le dos de

l’appareil contre le mur.

3Installation du capteur extérieur

Codes d’erreur (Contrôleur central portable)

Si l’écran affiche E1 ou E, au cours de l’installation, vérifier le numéro du code d’erreur :

29 Tentative de connexion de dispositifs sans fils incompatibles.

34 Force de signal faible. Déplacer le dispositif sans fil à un emplacement différent et

essayer de nouveau.

38 S’assurer que le voyant Connect du récepteur sans fil clignote et que l’opérateur se

trouve à au moins deux pieds de ce dernier.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Mitsubishi Electric Steuerungssystem Handbücher

Mitsubishi Electric

Mitsubishi Electric AL2-EEPROM-2 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCU-68DAVN Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS C6 Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric LMAP02-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT40ANRA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AE-200A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MEHITS MANAGER 3000+ Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AE-200A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YG81TB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric C70 Benutzerhandbuch

Mitsubishi Electric

Mitsubishi Electric MJ-310E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Evolution+ s-MEXT Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CNC 700 Series Gebrauchsanweisung

Mitsubishi Electric

Mitsubishi Electric C80 Series Einrichtungshandbuch

Mitsubishi Electric

Mitsubishi Electric AE-200A/AE-50A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric par-u02meda Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric GB-24A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AG-150A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELDAS C6 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric BAC-HD150 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J2S Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PAC-YT34STA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric BAC-HD150 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AE-200A Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung