Mitsubishi Electric MELSEC Q Series Bedienungsanleitung

PROFIBUS-DP Master Module

User's Manual

-QJ71PB92V

A- 1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention

to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of the

programmable controller system, refer to the user’s manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION"

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

When a communication error occurs on PROFIBUS-DP, the status of the faulty station is as shown

below.

Create an interlock circuit in the sequence program using the communication status information to

ensure the system operates safely (Input X1, buffer memory 5A20Hto 5B19H(23072 to 23321)).

An erroneous output or malfunction may cause accidents.

(1) The QJ71PB92V holds the input data before the communication failure.

(2) When the QJ71PB92V has gone down, the output status of each DP-Slave is dependent on the

QJ71PB92V parameter setting on GX Configurator-DP.

(3) When a DP-Slave has gone down, the output status of the other DP-Slaves is dependent on the

QJ71PB92V parameter setting on GX Configurator-DP.

Do not output the "use prohibited" signal as the output signal to an intelligent function module from

the programmable controller CPU.

Doing so may cause malfunction of the programmable controller system.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

A- 2

[Design Precautions]

WARNING

When a stop error has occurred to the CPU module, the communication status varies depending on

the error time output mode setting of GX Works2 as shown below.

Set the communication status for when a stop error has occurred to the CPU module according to

the system specifications.

Note that, if the QJ71PB92V is mounted to a redundant system, it operates as described in (1) below

regardless of the setting.

(1) When "Error time output mode" is set to "Hold"

(a) Since the communication with the DP-Slave is continued, values at the time of the CPU

module stop error occurrence are held as the output data sent to the DP-Slave from the

QJ71PB92V.

(b) Input data received from DP-Slaves are updated into the buffer memory of the QJ71PB92V.

(2) When "Error time output mode" is set to "Clear"

(a) Communications with DP-Slaves are interrupted, and output data are not sent.

(b) Input data received from DP-Slaves are held in the buffer memory of the QJ71PB92V.

When the QJ71PB92V is mounted in a redundant system, set the watchdog timer for DP-Slaves so

that the calculation formula shown in Section 4.8 (5) is satisfied.

If the formula is not satisfied, a watchdog timer error occurs in DP-Slaves during system switching.

CAUTION

Do not install PROFIBUS cables together with the main circuit or power lines or bring them close to

each other.

Keep a distance of 100mm (3.94 inches) or more between them.

Failure to do so may result in malfunction due to noise.

A- 3

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications in the

user's manual for the CPU module used.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of the

product.

To mount the module, while pressing the module mounting lever located in the lower part of the

module, fully insert the module fixing projection(s) into the hole(s) in the base unit and press the

module until it snaps into place.

Incorrect mounting may cause malfunction, failure or drop of the module.

When using the programmable controller in an environment of frequent vibrations, fix the module

with a screw.

Tighten the screw within the specified torque range.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

Shut off the external power supply (all phases) used in the system before mounting or removing the

module.

Failure to do so may result in damage to the product.

Do not directly touch any conductive parts and electronic components of the module.

Doing so can cause malfunction or failure of the module.

A- 4

[Wiring Precautions]

WARNING

Be sure to shut off all phases of the external power supply used by the system before wiring

PROFIBUS cables.

Failure to do so may cause the module to fail or malfunction.

CAUTION

Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

Be sure to place the PROFIBUS cables in a duct or clamp them.

If not, dangling cable may swing or inadvertently be pulled, resulting in damage to the module or

cables or malfunction due to poor contact.

When disconnecting the PROFIBUS cable, do not pull it by holding the cable part.

Be sure to hold its connector which is plugged into the module.

Pulling the cable with it connected to the module may damage the module and/or cable, or cause

malfunctions due to poor contact of the cable.

A protective film is attached to the top of the module to prevent foreign matter, such as wire chips,

from entering the module during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

A- 5

[Startup and Maintenance Precautions]

[Disposal Precautions]

WARNING

Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the connector screws or module fixing screws.

Failure to do so may result in electric shock or cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

CAUTION

Do not disassemble or modify the modules.

Doing so may cause failure, malfunction, injury, or a fire.

Use any radio communication device such as a cellular phone or PHS (Personal Handy-phone

System) more than 25cm (9.85 inches) away in all directions from the programmable controller.

Failure to do so may cause malfunction.

Shut off the external power supply (all phases) used in the system before mounting or removing the

module.

Failure to do so may cause the module to fail or malfunction.

After the first use of the product, do not mount/remove the module to/from the base unit more than

50 times (IEC 61131-2 compliant).

Exceeding the limit may cause malfunction.

Before handling the module, touch a grounded metal object to discharge the static electricity from the

human body.

Failure to do so may cause the module to fail or malfunction.

CAUTION

When disposing of this product, treat is as an industrial waste.

A- 6

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or serious accident;

and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the PRODUCT for the

case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED TO ANY AND ALL

RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY

INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE

OPERATED OR USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR

WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL

BULLETINS AND GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any other cases in which the

public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of a special quality

assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator and Escalator,

Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for Recreation and Amusement, and

Safety devices, handling of Nuclear or Hazardous Materials or Chemicals, Mining and Drilling, and/or other

applications where there is a significant risk of injury to the public or property.

Notwithstanding the above restrictions, Mitsubishi may in its sole discretion, authorize use of the PRODUCT in one or

more of the Prohibited Applications, provided that the usage of the PRODUCT is limited only for the specific

applications agreed to by Mitsubishi and provided further that no special quality assurance or fail-safe, redundant or

other safety features which exceed the general specifications of the PRODUCTs are required. For details, please

contact the Mitsubishi representative in your region.

A- 7

REVISIONS

* The manual number is given on the bottom left of the back cover.

Print Date * Manual Number Revision

Aug., 2005 SH (NA)-080572ENG-A First edition

Jun., 2006 SH (NA)-080572ENG-B

SAFETY PRECAUTIONS, GLOSSARY, Section 1.1, 2.1, 2.2.1, 2.4, 3.1 to

3.5, Chapter 4, Section 4.1.1, 4.1.3, 4.2.1 to 4.2.3, 4.5, 4.6, 5.3, 5.4, 6.1 to

6.3, 6.5, 6.6.4, Chapter 7 to Section 7.1.3, 9.4, Appendix 2

Section 2.3 , 3.5.3, 4.7, 4.8, 5.2.2, 6.7, 7.7, 7.9, 8.1, 9.3, 9.4.1 to 9.4.6,

Appendix 1

Section 5.2 5.2.1, Section 7.7 7.8, Section 8.1 to 8.2 Section 8.2 to

Section 8.3, Appendix 1 to Appendix 2 Appendix 2 to Appendix 3

May, 2007 SH (NA)-080572ENG-C • Rewritten to include the QJ71PB92D-compatible function.

• Modified for descriptions of GX Configurator-DP Version 7.02C.

"PLC" was changed to "programmable controller".

SAFETY PRECAUTIONS, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, ABOUT MANUALS, GLOSSARY, Chapter 1, Section 1.1,

2.1, 2.4, 3.5.1, 4.5, 4.6, 5.3, 6.1, 6.3 to 6.7, Chapter 7, Section 8.1 to 8.3,

Chapter 9 to Section 9.1, 9.3, 9.5.1 to 9.5.6, Appendix 1 to 2.3

Section 4.9, 9.2

Section 9.2 to 9.5 9.3 to 9.6

Dec., 2011 SH (NA)-080572ENG-D • Revision related to the support of GX Configurator-DP Version 7.07H

SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW VOLTAGE

DIRECTIVES, ABOUT THE GENERIC TERMS AND ABBREVIATIONS,

Section 2.1, 2.3.1, 3.3.1, 3.3.2, 3.4.4 to 3.4.6, 3.4.13, 4.1.3, 4.4, 4.5, 4.8, 4.9,

5.4, 5.5.1, Chapter 6, Section 6.2 to 6.5, Section 6.6.1 to 6.6.4, Chapter 7,

Section 7.1, 7.1.1, 7.1.2, 7.9.1, 8.1, 9.2, Appendix 2.2, WARRANTY

CONDITIONS OF USE FOR THE PRODUCT, MANUAL ORGANIZATION,

Section 2.3.3

Jun., 2015 SH (NA)-080572ENG-E

ABOUT THE GENERIC TERMS AND ABBREVIATIONS, Section 2.1, 3.1,

3.4.10, 4.9, 5.4, 7.4.3, 6.6.4, 9.1, 9.2, 9.3, 9.5.2, 9.5.3, 9.5.4, 9.5.5, 9.5.6, 9.6,

Appendix 2.1

Modifications

Additions

Section number changes

Change of a term

Modifications

Additions

Section number changes

Modifications

Additions

Modifications

A- 8

Japanese Manual Version SH-080571-I

Sep. 2018 SH (NA)-080572ENG-F

Related Manuals, Chapter 1, Section 1.1, 2.1, 2.4, Chapter 4, Section 4.6,

4.8, 5.3.1, 5.3.2, Chapter 6, Section 6.6.1, 6.6.2, 6.6.3, 6.7, 7.1, 7.8.1, 7.9.1,

9.1, 9.2, 9.4.2, 9.4.3, 9.5

Appendix 3 Appendix 1

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.

Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may

occur as a result of using the contents noted in this manual.

Print Date * Manual Number Revision

Modifications

Section number changes

Andere Handbücher für MELSEC Q Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Controller Handbücher

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2N-32DP-IF Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric QJ71DN91 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PZ-61DR-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX2N-10GM Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Melservo MR-J3-10B Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R C Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J4-B-LL Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC-A0J2H Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2N-16CCL-M Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AE-200A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric RD77GF8 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric CR750-D Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric CR800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Procon BAC-IP50 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX2N-2DA Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung