Mitsubishi Electric FR-A8APS-02 Bedienungsanleitung

INVERTER

Plug-in option

INSTRUCTION MANUAL

PRE-OPERATION INSTRUCTIONS 1

INSTALLATION AND WIRING 2

SSI communication functions 3

INVERTER SETTING 4

TROUBLESHOOTING 5

FR-A8APS-02

SSI communication function

Thank you for choosing this Mitsubishi Electric inverter plug-in option.

This Instruction Manual provides handling information and precautions for use of this product. Incorrect handling might cause an unexpected

fault. Before using this product, read all relevant instruction manuals carefully to ensure proper use.

Please forward this Instruction Manual to the end user.

Electric shock prevention

Injury prevention

Safety instructions

Do not attempt to install, operate, maintain or inspect this product until you have read this Instruction Manual and supplementary documents

carefully. Do not use this product until you have a full knowledge of this product mechanism, safety information and instructions. In this

Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Incorrect handling may cause hazardous conditions, resulting in death or severe injury.

Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only

material damage.

Note that even the level may lead to a serious consequence depending on conditions. Be sure to follow the

instructions of both levels as they are critical to personnel safety.

WARNING

Do not remove the front cover or the wiring cover of the inverter while the inverter power is ON. Do not operate the inverter with any cover or wiring cover removed,

as accidental contact with exposed high-voltage terminals and internal components may occur, resulting in an electrical shock.

Even if power is OFF, do not remove the front cover of the inverter except for wiring or periodic inspection as you may accidentally touch the charged circuits and

get an electric shock.

Before wiring or inspection, check that the display of the inverter operation panel is OFF. Any person who is involved in wiring or inspection shall wait for 10 minutes

or longer after power OFF and check that there are no residual voltage using a tester or the like. The capacitor is charged with high voltage for some time after

power OFF, and it is dangerous.

Any person who is involved in wiring or inspection of this product shall be fully competent to do the work.

This product must be installed before wiring. Otherwise you may get an electric shock or be injured.

Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Doing so may cause an electric shock.

Do not touch this product or handle the cables with wet hands. Doing so may cause an electric shock.

CAUTION

The voltage applied to each terminal must be as specified in the Instruction Manual. Otherwise an explosion or damage may occur.

The cables must be connected to the correct terminals. Otherwise an explosion or damage may occur.

The polarity (+ and -) must be correct. Otherwise an explosion or damage may occur.

While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Doing so may cause burns.

WARNING

CAUTION

Additional instructions

The following instructions must be also followed. If this product is handled incorrectly, it may cause unexpected fault, an injury, or an electric

shock.

CAUTION

Transportation and installation

Do not stand or place heavy objects on this product.

Ensure the mounting orientation of this product is correct.

Do not install or operate this product if it is damaged or has parts missing.

Foreign conductive objects must be prevented from entering the inverter. That includes screws and metal fragments or other flammable substance such as oil.

If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood packages enter this product, the product may be damaged. Prevent

the entry of fumigant residuals or use an alternative method such as heat disinfection. Note that sterilization or disinfection of wood packages should be performed

before packing the product.

Test operation

Before starting operation, confirm or adjust the parameter settings. Failure to do so may cause some machines to make unexpected motions.

WARNING

Usage

Do not modify this product.

Do not remove any part which is not instructed to be removed in the Instruction Manuals. Doing so may lead to a failure or damage of this product.

CAUTION

Usage

As all parameters return to their initial values after Parameter clear or All parameter clear is performed, the needed parameters for operation of the inverter and this

product must be set again before the operation is started.

To avoid damage to this product due to static electricity, static electricity in your body must be discharged before you touch this product.

Maintenance, inspection and parts replacement

Do not carry out a megger (insulation resistance) test.

Disposal

This product must be treated as industrial waste.

General instruction

For clarity, illustrations in this Instruction Manual may be drawn with covers or safety guards removed. Ensure all covers and safety guards are properly installed

prior to starting operation.

─CONTENTS ─

1 PRE-OPERATION INSTRUCTIONS 6

1.1 Unpacking and product confirmation.......................................................................................................6

1.1.1 Product confirmation.......................................................................................................................................6

1.2 Component names .....................................................................................................................................7

2 INSTALLATION AND WIRING 8

2.1 Pre-installation instructions ......................................................................................................................8

2.2 Installation procedure ................................................................................................................................8

2.3 Wiring ........................................................................................................................................................11

2.4 Terminals...................................................................................................................................................12

3 SSI communication functions 13

3.1 Supported distance meters .....................................................................................................................13

3.2 Connection example ................................................................................................................................14

4 INVERTER SETTING 15

4.1 Parameter list............................................................................................................................................15

4.2 Parameter adjustment..............................................................................................................................17

5 TROUBLESHOOTING 20

5.1 Troubleshooting .......................................................................................................................................20

5.2 Distance meter fault (system failure)......................................................................................................21

APPENDIX 22

Appendix1 Instructions for compliance with the EU Directives ....................................................................................... 22

Appendix2 Instructions for EAC .......................................................................................................................................... 23

Appendix3 Restricted Use of Hazardous Substances in Electronic and Electrical Products ....................................... 24

Appendix4 Referenced Standard (Requirement of Chinese standardized law) .............................................................. 25

6PRE-OPERATION INSTRUCTIONS

1PRE-OPERATION INSTRUCTIONS

1.1 Unpacking and product confirmation

Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact.

This product is a plug-in option dedicated for the FR-A800-AWH series inverter.

1.1.1 Product confirmation

Check the enclosed items.

NOTE

• Connection diagrams in this Instruction Manual appear with the control logic of the input terminals as sink logic, unless

otherwise specified. (For the control logic, refer to the Instruction Manual of the inverter.)

Plug-in option

.................................................. 1

Mounting screw (M3

8 mm)

...................... 2 (Refer to

page 8

)

Spacer

......................2 (Refer to

page 8

)

SW1

PRE-OPERATION INSTRUCTIONS 7

1.2 Component names

Symbol Name Description Refer to page

a Mounting hole Used to fix this product to the inverter by inserting a mounting screw

or a spacer. 8

b Terminal block Connected with an SSI device. 12

c Switch for manufacturer setting (SW1) Do not change the initially-set status.

(OFF (setting position marked with the white line)) ―

d CON2 connector Not used. ―

e Connector Connects to the option connector of the inverter. 8

TST2

UP UN

TST3 TST4 TST5 TST6

TST1

UP UN

DT+ CK+

DT- CK-

Front view Rear view

Terminal layout

(a) (e)

(a)

(d)

(a)

(c)

(b)

SW1

Do not use terminals

TST1 to TST6 and UP.

When using terminal UN,

use the upper one.

8INSTALLATION AND WIRING

2INSTALLATION AND WIRING

2.1 Pre-installation instructions

Check that the inverter's input power and the control circuit power are both OFF.

2.2 Installation procedure

CAUTION

Do not install or remove this product while the inverter power is ON. Otherwise, the inverter and plug-in option may be damaged.

To avoid damage due to static electricity, static electricity in your body must be discharged before you touch the product.

(1) Remove the inverter front cover. (Refer to the FR-A800

Instruction Manual (Detailed) for instructions to remove

the front cover.)

(2) Insert two spacers into the mounting holes that will not be

used for mounting screws (see the diagrams on the next

page to identify the holes).

(3) Fit the board mounted option connector on this product to

the guide of the option connector on the inverter, and

insert the option as far as it goes.

(4) Fasten this product to the inverter using the two mounting

screws through the holes on either side (tightening torque

0.33 N∙m to 0.40 N∙m). If the screw holes do not line up,

the connector may not be inserted deep enough. Check

the connector.

Example of installation to connector 1

Spacer

Option connector

on the inverter

INSTALLATION AND WIRING 9

Spacer

Mounting screw

Spacer

Mounting screw

Connector 1Connector 2

Connector 3

Insertion positions for screws and spacers

10 INSTALLATION AND WIRING

NOTE

• When installing/removing the plug-in option, hold the sides of the option. Do not press on the parts on the option circuit

board. Stress applied to the parts by pressing, etc. may cause a failure.

• Be careful not to drop mounting screws during the installation or removal of the plug-in option.

• Only one option attached to the option connector with high priority can function at once if more than one option of the

same name are installed together on an inverter. Priority is given to option connectors in descending order (1 to 3),

and options having a lower priority do not function.

• When the inverter cannot recognize the option due to improper installation or any other reason or when a option fault

or SSI communication error occurs, the protective function (E.1 to E.4) is activated and the inverter cannot be

operated. An indication from E.1 to E.3 is displayed depending on the connector used (option connector 1 to 3).

"E.4" is displayed when an error status is included in SSI communication data received from this option.

• When removing the plug-in option, remove the two screws on either side, and then pull it straight out. Pressure applied

to the option connector and to the option board may break the option.

Mounted position Fault indication

Option connector 1

Option connector 2

Option connector 3

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A872-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric F800-E Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FX-1PG Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F802-E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-CC2-H315K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PV-PNS03ATL-GER Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A760-00017-NA Merkblatt

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Betriebsanleitung

Mitsubishi Electric

Mitsubishi Electric 800-GF Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-S500E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A700 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-ABR-(H)0.4K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F 740 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A500 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F862-E Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-HEL-N280K Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung