Mitsubishi Electric Fr-e700 series Bedienungsanleitung

MITSUBISHI ELECTRIC

INDUSTRIAL AUTOMATION

FR-E700

Inverters

Instruction Manual

FR-E720SSC EC

FR-E740SC EC

10052011

Version A

Instruction Manual

Inverter FR-E700SC EC

Version Changes / Additions / Corrections

A 05/2011 akl/rwi —

FR-E700SC EC I

Thank you for choosing this Mitsubishi inverter.

This instruction manual provides instructions for advanced use of the FR-E700SC series inverters. In-

correct handling might cause an unexpected fault. Before using the inverter, always read this instruc-

tion manual to use the equipment to its optimum.

Safety Instructions

Do not attempt to install, operate, maintain or inspect the inverter until you have read through this

instruction manual carefully and can use the equipment correctly. Do not use the inverter until you

have a full knowledge of the equipment, safety information and instructions. In this instruction

manual, the safety instruction levels are classified into "WARNING" and "CAUTION".

Note that even the CAUTION level may lead to a serious consequence according to conditions. Please

follow strictly the instructions of both levels because they are important to personnel safety.

WARNING:

Assumes that incorrect handling may cause hazardous conditions, resulting in death or severe

injury.

CAUTION:

Assumes that incorrect handling may cause hazardous conditions, resulting in medium or slight

injury, or may cause physical damage only.

Electric Shock Prevention

WARNING:

●While power is on or when the inverter is running, do not open the front cover. Otherwise

you may get an electric shock.

●Do not run the inverter with the front cover removed. Otherwise,youmayaccessthe exposed

high-voltage terminals or the charging part of the circuitry and get an electric shock.

●Even if power is off, do not remove the front cover except for wiring or periodic inspection.

You may access the charged inverter circuits and get an electric shock.

●Before starting wiring or inspection, check to make sure that the operation panel indicator

is off, wait for at least 10 minutes after the power supply has been switched off, and check

that there are no residual voltage using a tester or the like. The capacitor is charged with

high voltage for some time after power off and it is dangerous.

●This inverter must be earthed. Earthing must conform to the requirements of national and

local safety regulations and electrical codes. (JIS, NEC section 250, IEC 536 class 1 and other

applicable standards)

Use a neutral-point earthed (grounded) power supply for 400V class inverter in compliance

with EN standard.

●Any person who is involved in the wiring or inspection of this equipment should be fully

competent to do the work.

●Always install the inverter before wiring. Otherwise, you may get an electric shock or be

injured.

●If your application requires by installation standards an RCD (residual current device) as up

stream protection please select according to DIN VDE 0100-530 as following:

Single phase inverter type A or B

Three phase inverter only type B

●Perform setting dial and key operations with dry hands to prevent an electric shock. Other-

wise you may get an electric shock.

●Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Otherwise

you may get an electric shock.

●Do not replace the cooling fan while power is on. It is dangerous to replace the cooling fan

while power is on.

●Do not touch the printed circuit board with wet hands. You may get an electric shock.

●When measuring the main circuit capacitor capacity, the DC voltage is applied to the motor

for 1s at powering off. Never touch the motor terminal, etc. right after powering off to

prevent an electric shock.

FR-E700SC EC III

Fire Prevention

Injury Prevention

CAUTION:

●Mount the inverter to incombustible material. Install the inverter on a nonflammable wall

without holes (so that nobody can touch the inverter heatsink on the rear side, etc.). Mount-

ing it to or near combustible material can cause a fire.

●If the inverter has become faulty, switch off the inverter power. A continuous flow of large

current could cause a fire.

●When using a brake resistor, make up a sequence that will turn off power when an alarm

signal is output. Otherwise, the brake resistor may excessively overheat due to damage of

the brake transistor and such, causing a fire.

●Do not connect a resistor directly to the DC terminals P/+, N/–. This could cause a fire and

destroy the inverter. The surface temperature of braking resistors can far exceed 100°C for

brief periods. Make sure that there is adequate protection against accidental contact and a

safe distance is maintained to other units and system parts.

CAUTION:

●Apply only the voltage specified in the instruction manual to each terminal. Otherwise,

burst, damage, etc. may occur.

●Ensure that the cables are connected to the correct terminals. Otherwise, burst, damage, etc.

may occur.

●Always make sure that polarity is correct to prevent damage, etc. Otherwise, burst, damage,

etc. may occur.

●While power is on or for some time after power-off, do not touch the inverter as it is hot and

you may get burnt.

Additional Instructions

Also note the following points to prevent an accidental failure, injury, electric shock, etc.

Transport and Installation



Temperature applicable for a short time, e.g. in transit.

Wiring

Trial Run

CAUTION:

●Transport the product using the correct method that corresponds to the weight. Failure to

observe this could lead to injuries.

●Do not stack the inverter boxes higher than the number recommended.

●Ensure that installation position and material can withstand the weight of the inverter.

Install according to the information in the instruction manual.

●Do not install or operate the inverter if it is damaged or has parts missing. This can result in

breakdowns.

●When carrying the inverter, do not hold it by the front cover or setting dial; it may fall off or

fail.

●Do not stand or rest heavy objects on the product.

●Check the inverter mounting orientation is correct.

●Prevent other conductive bodies such as screws and metal fragments or other flammable

substance such as oil from entering the inverter.

●As the inverter is a precision instrument, do not drop or subject it to impact.

●Use the inverter under the following environmental conditions. Otherwise, the inverter may

be damaged.

Operating Condition Specifications

Ambient temperature −10°C to +50°C (non-freezing)

Ambient humidity 90% RH or less (non-condensing)

Storage temperature −20°C to +65°C



Atmosphere Indoors (free from corrosive gas, flammable gas, oil mist, dust and dirt)

Altitude Maximum 1000m above sea level for standard operation.

After that derate by 3% for every extra 500m up to 2500m (91%)

Vibration 5.9m/s² or less at 10 to 55Hz (directions of X, Y, Z axes)

CAUTION:

●Do not install assemblies or components (e. g. power factor correction capacitors) on the

inverter output side, which are not approved from Mitsubishi.

●The direction of rotation of the motor corresponds to the direction of rotation commands

(STF/STR) only if the phase sequence (U, V, W) is maintained.

CAUTION:

●Before starting operation, confirm and adjust the parameters. A failure to do so may cause

some machines to make unexpected motions.

FR-E700SC EC V

Operation

WARNING:

●When you have chosen the retry function, stay away from the equipment as it will restart

suddenly after an alarm stop.

●Since pressing the STOP/RESET-key may not stop output depending on the function setting

status, provide a circuit and switch separately to make an emergency stop (power off,

mechanical brake operation for emergency stop, etc.).

●Make sure that the start signal is off before resetting the inverter alarm. A failure to do so

may restart the motor suddenly.

●The load used should be a three-phase induction motor only. Connection of any other

electrical equipment to the inverter output may damage the equipment.

●Do not modify the equipment.

●Do not perform parts removal which is not instructed in this manual. Doing so may lead to

fault or damage of the inverter.

CAUTION:

●The electronic thermal relay function does not guarantee protection of the motor from

overheating. It is recommended to install both an external thermal and PTC thermistor for

overheat protection.

●Do not use a magnetic contactor on the inverter input for frequent starting/stopping of the

inverter. Otherwise, the life of the inverter decreases.

●Usea noise filterto reduce the effect ofelectromagnetic interferenceand follow theaccepted

EMC procedures for proper installation of frequency inverters. Otherwise nearby electronic

equipment may be affected.

●Take appropriate measures regarding harmonics. Otherwise this can endanger compensa-

tion systems or overload generators.

●Use a motor designed for inverter operation. (The stress for motor windings is bigger than

in line power supply).

●When parameter clear or all clear is performed, set again the required parameters before

starting operations. Each parameter returns to the initial value.

●The inverter can be easily set for high-speed operation. Before changing its setting, fully

examine the performances of the motor and machine.

●The DC braking function of the frequency inverter is not designed to continuously hold a

load. Use an electro-mechanical holding brake on the motor for this purpose.

●Before running an inverter which had been stored for a long period, always perform inspec-

tion and test operation.

●For prevention of damage due to static electricity, touch nearby metal before touching this

product to eliminate static electricity from your body.

Emergency Stop

Maintenance, Inspection and Parts Replacement

Disposing the Inverter

General Instructions

Many of the diagrams and drawings in instruction manuals show the inverter without a cover, or par-

tially open. Never run the inverter in this status. Always replace the cover and follow this instruction

manual when operating the inverter.

CAUTION:

●Provide a safety backup such as an emergency brake which will prevent the machine and

equipment from hazardous conditions if the inverter fails.

●When the breaker on the inverter primary side trips, check for the wiring fault (short circuit),

damage to internal parts of the inverter, etc. Identify the cause of the trip, then remove the

cause and power on the breaker.

●When the protective function is activated (i. e. the frequency inverter switches off with an

error message), take the corresponding corrective action as described in the inverter man-

ual, then reset the inverter, and resume operation.

CAUTION:

●Do not carry out a megger (insulation resistance) test on the control circuit of the inverter.

It will cause a failure.

CAUTION:

●Treat as industrial waste.

Andere Handbücher für fr-e700 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Electric Wechselrichter Handbücher

Mitsubishi Electric

Mitsubishi Electric FR-A7NP Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-D720-008 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric F700 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F720-00046 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F700PJ Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NC E kit-SC Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric melpto d series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-V560 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A820-00046 (0.4K) Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A7NL Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A5AX Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A8APS-02 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric FR-A800 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 700 Series Merkblatt

Mitsubishi Electric

Mitsubishi Electric FR-A500L Series Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 800 Series Montageanleitung

Mitsubishi Electric

Mitsubishi Electric FR-F740 EC Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung