Mitsubishi QJ71AS92 Gebrauchsanweisung

AS-i Master Module

User’s Manual

(Hardware)

QJ71AS92

Thank you for purchasing the Mitsubishi programmable controller

MELSEC-Q series.

Prior to use, please read this and relevant manuals thoroughly to

fully understand the product.

MODEL QJ71AS92-U-H

MODEL

CODE 13JT88

IB(NA)-0800225-D(0807)MEE

2002 MITSUBISHI ELECTRIC CORPORATION

-1

DANGER

CAUTION

zSAFETY PRECAUTIONS z

(Always read these instructions before using this equipment.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The instructions given in this manual are concerned with this product only. For

the safety instructions of the programmable controller system, please read the

user's manual for the CPU module to use.

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury or

physical damage.

Note that the CAUTION level may lead to a serious consequence according

to the circumstances.

Always follow the instructions of both levels because they are important to

personal safety.

Please save this manual to make it accessible when required and always forward

it to the end user.

-2

[Design Precautions]

CAUTION

zDo not bunch AS-i cable with the main circuit or power wires, or install them

close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

[Installation Precautions]

CAUTION

zUse the programmable controller in an environment that meets the general

specifications in CPU module User’s Manual.

Using the programmable controller in an environment outside the range of

the general specifications could result in electric shock, fire, erroneous

operation, and damage to or deterioration of the product.

zDo not touch conductive parts or electronic components of the module with

your bare hands.

This could cause malfunction or failure of the module.

zWhile pressing the lever on the lower part of the module, fully insert the

module fixing latch into the hole of the base unit, snap the module into place,

and tighten the module fixing screws with the specified torque.

Failure to observe this could result in damage to the screws or module,

module falling, short or misoperation.

If the screws are tightened excessively, it may damage the screws and

cause the module to short-circuit, malfunction or fall off.

zAlways shut off all phases of the programmable controller power supply and

AS-i power supply externally before mounting or removing the module.

Failure to shut off all phases could lead to product damage.

-3

[Wiring Precautions]

DANGER

zSwitch off all phases of the programmable controller power supply and AS-i

power supply outside the programmable controller before starting installing

or wiring work.

There is a risk of electric shock or malfunction.

CAUTION

zAlways confirm the products terminal layout before wiring to the module.

Incorrect wiring could lead to fires or faults.

zWiring installation screws to the specified torque.

If a wiring installation screws is not tightened to the specified torque, the

module may fall out, short circuit, or malfunction.

If a wiring installation screws is tightened excessively, exceeding the

specified torque, the module may fall out, short circuit, or malfunction due to

breakage of the screw or the module.

zMake sure that no foreign matter such as chips or wire offcuts gets inside the

module.

It will cause fire, failure, or malfunction.

zA label is installed at the upper part of a module to prevent the entry of foreign

matters.

Do not remove the label during wiring.

However, be sure to remove it for heat dissipation during system operation.

zTo connect the AS-i cable to the module, the cable must be securely fixed.

Please be sure to run it in a duct, or clamp it.

Failure to observe this could cause the unstable cable connection, resulting

in damage to the cable or module by carelessly pulling the cable, or the

system malfunction due to poor cable connection.

zWhen removing AS-i cable from a module, do not pull it out by hand.

Always be sure to unscrew the module mounting screws in advance.

If the cable is pulled while being connected to the module, it could cause

damage to the cable or module, or the system malfunction due to poor cable

connection.

-4

Revisions

*The manual number is given on the bottom right of the top cover.

Print Date *Manual Number Revision

Mar., 2002 IB(NA)-0800225-A First edition

Jun., 2004 IB(NA)-0800225-B

Partial correction

SAFETY PRECAUTIONS, Section 3.1, 5.1

Mar., 2006 IB(NA)-0800225-C

Partial correction

SAFETY PRECAUTIONS, Compliance

with the EMC and Low Voltage Directives,

Chapter 1, 2

Jul., 2008 IB(NA)-0800225-D

Change of a term

"PLC" was changed to "programmable

controller".

Partial correction

Compliance with the EMC and Low Voltage

Directives, Section 3.1, Chapter 4, 6

This manual confers no industrial property rights or any rights of any other kind, nor does it

confer any patent licenses. Mitsubishi electric Corporation cannot be held responsible for

any problems involving industrial property rights which may occur as a result of using the

contents noted in this manual.

2002 MITSUBISHI ELECTRIC CORPORATION

-5

CONTENTS

1. Overview ······································································································· 1

2. Performance Specifications ·········································································· 1

3. Loading and Installation ················································································ 2

3.1 Handling··································································································· 2

3.2 Installation Environment ··········································································· 3

4. Name and Setting of the Parts ······································································ 3

5. Wiring ··········································································································· 5

5.1 Precautions against wiring········································································ 5

5.2 Wiring······································································································· 5

6. External Dimensions Diagram ······································································· 6

-6

About Manual

The following manual is also related to this product.

In necessary, order it by quoting the details in the table below.

Related Manual

Manual name Manual No.

(Model code)

AS-i Master Module User’s Manual SH-080291E

(13JR53)

Compliance with the EMC and Low Voltage Directives

(1) For programmable controller system

To configure a system meeting the requirements of the EMC and Low

Voltage Directives when incorporating the Mitsubishi programmable

controller (EMC and Low Voltage Directives compliant) into other

machinery or equipment, refer to Chapter 9 "EMC AND LOW VOLTAGE

DIRECTIVES" of the QCPU User's Manual (Hardware Design,

Maintenance and Inspection).

The CE mark, indicating compliance with the EMC and Low Voltage

Directives, is printed on the rating plate of the programmable controller.

(2) For the product

No additional measures are necessary for the compliance of this product

with the EMC and Low Voltage Directives.

1. Overview

This manual explains how to handle the AS-i Master module, model number

QJ71AS92 (hereinafter referred to as QJ71AS92).

After unpacking the QJ71AS92, confirm that the following products are enclosed.

Type Product Quantity

QJ71AS92 type AS-i master module 1

QJ71AS92 Connector 1

2. Performance Specifications

The following are the performance specifications of the QJ71AS92.

Item Specifications

Max. number of AS-i slaves *1 62 (Group A: 31, Group B: 31)

Input 248 pointsMax. number of I/O points

*2 (1 point = 1 bit) Output 248 points

Input 124 pointsMax. address of analog I/O

points (1 point = 16 bits) Output 124 points

I/O refresh time

Approx. 5ms (without I/O slave grouping)

Approx. 10ms (with I/O slave grouping)

Approx. 35ms (per analog slave channel)

Communication speed 167kbps

Transmission distance Max. 100m (max. 300m with two repeaters)

Connection type Bus network type (star, line, tree and ring)

Communication method APM modulation method (Alternating Pulse

Modulation)

Error control method Parity check

Internal memory EEPROM (for parameter registration), number of

writes: 100,000 times

Number of occupied I/O points 32 points (I/O assignment: 32 intelligent points)

Cable type Use dedicated AS-i cable.

Voltage TYP. 30.5VDC (supplied by AS-i power supply)External supply

power Current consumption 46mA (TYP 30.5VDC)

5VDC internal current consumption 0.40A

Weight 0.12kg

*1: This is the max. number of Ver. 2.11-compatible I/O slave stations (can be

grouped) configured in the same system. If Ver.2.11-compatible I/O slaves

that cannot be grouped, analog slaves, and Ver. 2.04-compatible I/O slaves

are used together in the same system, calculate the max. number of slaves

using the following expression.

{(NIO-A +NIO-B)+2 (NA+NIO)} < 62 (Group A 31, Group B 31)

Number of Group A Ver. 2.11-compatible I/O slaves : NIO-A

Number of Group B Ver. 2.11-compatible I/O slaves : NIO-B

Number of Ver. 2.11-compatible analog slaves : NA

Number of Ver. 2.04-compatible I/O slaves : NIO

Slave Type Grouping

AS-i Ver. 2.11-compatible I/O slave Please confirm with the manufacturer of the I/O

slave unit whether the unit can be grouped.

AS-i Ver. 2.04-compatible I/O slave

AS-i Ver. 2.11-compatible analog slave Disabled

*2: One slave uses four inputs and four outputs.

One analog slave also uses four inputs and four outputs.

For the general specifications of the QJ71AS92, refer to the user's manual of the

used CPU module.

3. Loading and Installation

The following section explains the precautions when handling the QJ71AS92,

from the time they are unpacked until they are installed.

For more details on the module installation, see the user's manual for the

programmable controller CPU used.

3.1 Handling

(1) Do not drop the module case and connector or subject it to heavy impact

since it is made of resin.

(2) Always make sure to touch the grounded metal to discharge the electricity

charged in the body, etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

(3) Tighten the screws such as module fixing screws within the following

ranges.

Screw location Tightening torque range

Module fixing screw (normally not required) (M3 screw) *1 0.36 to 0.48 Nym

Communication connector installation screw 0.40 to 0.50 Nym

Communication connector wiring installation screw 0.50 to 0.60 Nym

*1 The module can be easily fixed onto the base unit using the hook at the

top of the module.

However, it is recommended to secure the module with the module

fixing screw if the module is subject to significant vibration.

3.2 Installation Environment

Refer to user's manual of the CPU module used.

4. Name and Setting of the Parts

Following is an explanation of the QJ71AS92 part names and settings.

QJ71AS92

RUN

U ASI

ERR.

PRG ENA.

S ERR.

CODE

MODE

SET

ASI+

ASI-

ASI+

ASI-

(FG)

QJ71AS92

Inhaltsverzeichnis

Andere Mitsubishi Steuereinheit Handbücher

Mitsubishi

Mitsubishi L Series Bedienungsanleitung

Mitsubishi

Mitsubishi AL-ASI-BD Bedienungsanleitung

Mitsubishi

Mitsubishi QJ72LP25-25 Gebrauchsanweisung

Mitsubishi

Mitsubishi Melsec-A AJ65SBT Bedienungsanleitung

Mitsubishi

Mitsubishi FR-A5ND Bedienungsanleitung

Mitsubishi

Mitsubishi A1S62TCRTBW-S2 Bedienungsanleitung

Mitsubishi

Mitsubishi Q68TD-G-H01 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A A1S68AD Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A AJ71DN91 Bedienungsanleitung

Mitsubishi

Mitsubishi Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q Q06CCPU-V-B Bedienungsanleitung

Mitsubishi

Mitsubishi Q68RD3-G Bedienungsanleitung

Mitsubishi

Mitsubishi GOT 1000 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC System Q Bedienungsanleitung

Mitsubishi

Mitsubishi A6TE2-16SRN Bedienungsanleitung

Mitsubishi

Mitsubishi A8GT-50KBF Bedienungsanleitung

Mitsubishi

Mitsubishi QJ71WS96 Series Bedienungsanleitung

Mitsubishi

Mitsubishi A1SJ71AP21 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A A1SJ71AS92 Bedienungsanleitung

Mitsubishi

Mitsubishi FX1N-5DM Bedienungsanleitung

Mitsubishi

Mitsubishi Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi AJ71PB92D Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-L Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung