Mitsubishi MELSEC Q Series Bedienungsanleitung

FL-net(OPCN-2)

Interface Module

User’s Manual

(Hardware)

QJ71FL71-T-F01

QJ71FL71-B5-F01

QJ71FL71-B2-F01

Thank you for purchasing the Mitsubishi programmable controller

MELSEC-Q series.

Prior to use, please read this and relevant manuals thoroughly to

fully understand the product.

MODEL QJFL71-F01-U-HW

MODEL

CODE 13JP09

IB(NA)-0800239-E(0809)MEE

2002 MITSUBISHI ELECTRIC CORPORATION

-1

DANGER

CAUTION

zSAFETY PRECAUTIONS z

(Always read these instructions before using this equipment.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The instructions given in this manual are concerned with this product. For safety

instructions of the programmable controller system, please read the CPU module

user's manual.

In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury or

physical damage.

Note that the CAUTION level may lead to serious consequence according to

the circumstances. Always follow the instructions of both levels because they are

important to personal safety.

Please save this manual to make it accessible when required and always forward

it to the end user.

-2

[Design Precautions]

CAUTION

zDo not bunch the control wires or communication cables with the main circuit

or power wires, or install them close to each other.

They should be installed 100 mm (3.94 inch) or more from each other.

Not doing so could result in noise that would cause erroneous operation.

[Installation Precautions]

CAUTION

zUse the programmable controller in an environment that meets the general

specifications contained in this manual.

Using this programmable controller in an environment outside the range of

the general specifications could result in electric shock, fire, erroneous

operation, and damage to or deterioration of the product.

zWhile pressing the installation lever located at the bottom of module, insert

the module fixing tab into the fixing hole in the base unit until it stops. Then,

securely mount the module with the fixing hole as a supporting point.

Incorrect loading of the module can cause a malfunction, failure or drop.

When using the programmable controller in the environment of much

vibration, tighten the module with a screw.

zTighten the screw in the specified torque range.

Undertightening can cause a drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to damage

to the screw or module.

zBefore mounting or dismounting the module, make sure to shut off all phases

of the external power supply and FL-net (OPCN-2) system's power supply.

Failure to do so may damage the product.

zDo not directly touch the module's conductive parts or electronic

components.

Touching the conductive parts could cause an operation failure or give

damage to the module.

-3

[Wiring Precautions]

CAUTION

zWhen wiring the connectors for external cable connection, crimp or clamp

the wires with a tool specified by the manufacture or solder them. An

incomplete connection could cause malfunctions.

zDo not connect AUI cables when the programmable controllers on the station

where the module is mounted and the FL-net (OPCN-2) system are powered

ON.

zInstall the connector to the module securely.

zPlace the communication and power cables to be connected to the module in

a duct or fasten them using a clamp. If not, dangling cables may swing or

inadvertently be pulled, resulting in damage to the module or cables or

malfunctions due to poor cable contact.

zTighten the terminal screws with the specified torque.

If the terminal screws are loose, it could result in short circuits, fire, or

erroneous operation.

Tightening the terminal screws too far may cause damages to the screws

and/or the module, resulting in fallout, short circuits, or malfunction.

zWhen disconnecting a communication or power cable from the module, do

not pull the cable part by hand. When disconnecting a cable with a

connector, hold the connector connected to the module by hand and pull it

out. When disconnecting a cable connected to a terminal block, loosen the

screws on the terminal block first before removing the cable. Failure to do so

may cause a malfunction or damage to the module and/or cables.

zBe sure there are no foreign substances such as sawdust or wiring debris

inside the module.

Such debris could cause fires, damage, or erroneous operation.

zThe module has an ingress prevention label on its top to prevent foreign

matter, such as wire offcuts, from entering the module during wiring.

Do not peel this label during wiring.

Before starting system operation, be sure to peel this label because of heat

dissipation.

-4

Revisions

* The manual number is given on the bottom right of the cover.

Print Date *Manual Number Revision

June, 2002 IB(NA)-0800239-A First printing

July, 2003 IB(NA)-0800239-B Correction

About the Manuals, Chapter 1, Chapter 2,

Section 3.1, Chapter 4, Section 5.1, 5.2,

Chapter 6

Model addition

QJ71FL71-T-F01, QJ71FL71-B5-F01

Model deletion

QJ71FL71-F01

Mar., 2006 IB(NA)-0800239-C Correction

SAFETY PRECAUTIONS, Compliance

with the EMC and Low Voltage Directive,

Chapter 2, Chapter 4, Section 5.2, 5.4,

Chapter 6

Dec., 2007 IB(NA)-0800239-D Change of a term

"PLC" was changed to "programmable

controller".

Correction

SAFETY PRECAUTIONS, Compliance

with the EMC and Low Voltage Directive,

Chapter 2, Section 3.1, Chapter 4,

Chapter 5, Chapter 6

Sep., 2008 IB(NA)-0800239-E Correction

Compliance with the EMC and Low

Voltage Directives, Chapter 2, Section 3.1,

Chapter 4, Section 5.2, Chapter 6

This manual confers no industrial property rights or any rights of any other kind, nor does it

confer any patent licenses. Mitsubishi electric Corporation cannot be held responsible for

any problems involving industrial property rights which may occur as a result of using the

contents noted in this manual.

2002 MITSUBISHI ELECTRIC CORPORATION

-5

CONTENTS

1. Overview ······································································································· 1

2. Performance Specifications ·········································································· 1

3. Mounting and Installation ·············································································· 3

3.1 Precautions when handling ······································································ 3

3.2 Installation environment ··········································································· 3

4. Name of Parts ······························································································· 3

5. Connection to a Network················································································ 6

5.1 Connecting to 10BASE-T/100BASE-TX network ······································ 6

5.2 Connecting to 10BASE5 network ····························································· 7

5.3 Connecting to 10BASE2 network ····························································· 9

5.4 Switch settings for intelligent function module ·········································· 9

6. External Dimensions···················································································· 10

About Manual

The following manual is also related to this product.

If necessary, please place an order for it.

Related Manual

Manual name Manual No.

(Model code)

FL-net(OPCN-2) Interface Module User’s Manual

QJ71FL71-T-F01, QJ71FL71-B5-F01,

QJ71FL71-B2-F01

SH-080350E

(13JR61)

Compliance with the EMC and Low Voltage Directives

(1) For programmable controller system

To configure a system meeting the requirements of the EMC and Low

Voltage Directives when incorporating the Mitsubishi programmable

controller (EMC and Low Voltage Directives compliant) into other

machinery or equipment, refer to Chapter 9 "EMC AND LOW VOLTAGE

DIRECTIVES" of the QCPU User's Manual (Hardware Design,

Maintenance and Inspection).

The CE mark, indicating compliance with the EMC and Low Voltage

Directives, is printed on the rating plate of the programmable controller.

(2) For the product

For the compliance of this product with the EMC and Low Voltage

Directives, refer to Section 9.1.3 "Cables" in Chapter 9 "EMC AND LOW

VOLTAGE DIRECTIVES" of the QCPU User's Manual (Hardware Design,

Maintenance and Inspection).

1. Overview

This manual explains how to handle the FL-net (OPCN-2) interface module,

model numbers QJ71FL71-T-F01, QJ71FL71-B5-F01 and QJ71FL71-B2-F01

(hereinafter referred to as the FL-net module).

(Product composition)

Model name Product name Quantity

QJ71FL71-T-F01 QJ71FL71-T-F01 FL-net (OPCN-2) interface module 1

QJ71FL71-B5-F01 QJ71FL71-B5-F01 FL-net (OPCN-2) interface module 1

QJ71FL71-B2-F01 QJ71FL71-B2-F01 FL-net (OPCN-2) interface module 1

2. Performance Specifications

The following are the performance specifications of the FL-net module.

Specifications

QJ71FL71-B5

-F01

QJ71FL71-T

-F01

QJ71FL71-B2

-F01

Items

10BASE5 10BASE-T/

100BASE-TX 10BASE2

Data transmission speed 10 Mbps

(Half duplex)

10 Mbps

(Half duplex)

100 Mbps

(Full duplex/

Half duplex)

10 Mbps

(Half duplex)

Transmission method Base band

Electric interface IEEE802.3 standard (CSMA/CD standard)

Transmission protocol UDP/IP FA link protocol

Maximum distance

between nodes 2500 m — 925 m

Maximum segment length 500 m 100 m 185 m

Maximum number of nodes

in system 254

Maximum number of nodes 100/segment

For 10BASE-T,

Maximum 4

bases for

Cascade

connection

For 100BASE-TX,

Maximum 2

bases for

Cascade

connection

30/segment

Minimum node interval 2.5 m — 0.5 m

Cyclic data volume Maximum (8 k bits + 8 k words)/system

Maximum (8 k bits + 8 k words)/node

Transmission specifications

Message data volume Maximum 1024 bytes

Specifications

QJ71FL71-B5

-F01

QJ71FL71-T

-F01

QJ71FL71-B2

-F01

Items

10BASE5 10BASE-T/

100BASE-TX 10BASE2

Common memory area Area 1 (bit area): 8 k bits

Area 2 (word area): 8 k words

Virtual address space and

physical memory —

Error log memory area 512 words

Status memory area Bit area: 2 k bits

Word area: 2 k words

Local node network

parameter setting area 128 words

Other node network

parameter setting area 2048 words

Network parameter

acquisition area 512 words

Device profile memory

area 512 words

Link data specifications

Message area

(Transient area)

Maximum 1024 bytes 2 (1 for each of transmit and

receive)

Number of input/output points 32 points (I/O assignment: intelligent)

5V DC internal current

consumption 0.50 A 0.50 A 0.60 A (*2)

Noise resistance

Voltage resistance

Insulation resistance

According to the power supply specifications of the station

to which the FL-net module is mounted.

External dimensions 98 (3.86 in.)(H) 27.4 (1.08 in.)(W)

90 (3.54 in.)(D) mm

Weight 0.12 kg 0.11 kg 0.13 kg (*1)

*1: The 5V DC internal current consumption and weight of the product whose

first 5 digits of serial No. are 05079 or earlier are as follows:

• 5V DC internal current consumption : 0.70 A

• Weight : 0.14 kg

For general specifications of the FL-net module, refer to the user’s manual for the

CPU module that is to be used.

3. Mounting and Installation

3.1 Precautions when handling

This section explains the precautions for the FL-net module itself.

(1) The case for the FL-net module is plastic. Do not drop it or expose it to

strong impact.

(2) Before touching the module, always touch grounded metal, etc. to

discharge static electricity from human body, etc.

Not doing so can cause the module to fail or malfunction.

(3) Tighten the screws such as module fixing screws within the following

ranges.

Screw location Tightening torque

range

External power supply terminal screw (M2.5 screw) (*1) 0.40 N•m

Module fixing screw (Normally not required)

(M3 screw) (*2) 0.36 to 0.48 N•m

*1: External supply power input terminal to be used to supply power to the

transceiver for connection to 10BASE5.

*2: The module can be easily fixed onto the base unit using the hook at the top

of the module.

However, it is recommended to secure the module with the module fixing

screw if the module is subject to significant vibration.

3.2 Installation environment

Refer to the user’s manual for the CPU module that is to be used.

4. Name of Parts

The following introduces the functions and names of parts of the FL-net module.

6) 6)

7) 7)

Name Description

1) LED indicator Refer to (1) LED indication.

10BASE-T/100BASE-TX

connector (RJ45) (*2)

(for QJ71FL71-T-F01

only)

Connector for connecting FL-net module to

10BASE-T/100BASE-TX. (The FL-net module

detects the 10BASE-T or 100BASE-TX

according to the hub.)

10BASE5 connector

(for QJ71FL71-B5-F01

only)

Connector for connecting FL-net module to

10BASE5. (For connecting 10BASE5 AUI

cable (transceiver cable))

10BASE2 connector

(for QJ71FL71-B2-F01

only)

Connector for connecting FL-net module to

10BASE2.

(For connecting 10BASE2 coaxial cable)

5) External power supply

terminal

Terminal for supplying power to the

transceiver in the connection for 10BASE5.

(13.28 V to 15.75 V)

6) Lever for mounting

module

Guide for correctly mounting FL-net module to

base unit.

7) Serial number plate Indicates the serial No. of the FL-net module.

*1: The following is printed on a product whose serial No. (the first 5 digits) is

earlier than 10011.

Although the silkscreen print is different, the LED indications and connector

functionality are the same.

Part name Print

100M LED No print

10BASE-T/100BASE-TX connector 10BASE-T

Since the high-speed cyclic transmission function (100Mbps) by

100BASE-TX connection has been certified by Japan Electrical

Manufacture’s Association (JEMA), it can be used from the first released

products. (The QJ71FL71-T-F01 only)

*2: The LED on the connector will not light up.

Andere Handbücher für MELSEC Q Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Controller Handbücher

Mitsubishi

Mitsubishi FX2NC Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-Q EQ-V680D1 Bedienungsanleitung

Mitsubishi

Mitsubishi FX2N-64CL-M Bedienungsanleitung

Mitsubishi

Mitsubishi CMB-P-V-F Bedienungsanleitung

Mitsubishi

Mitsubishi Melsec A series Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U Series Bedienungsanleitung

Mitsubishi

Mitsubishi FX2NC-485ADP Bedienungsanleitung

Mitsubishi

Mitsubishi AL2-14MR-A Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC A1SCPU Montageanleitung

Mitsubishi

Mitsubishi FX2N-16CCL-M Bedienungsanleitung

Mitsubishi

Mitsubishi AJ65BT-D62 Bedienungsanleitung

Mitsubishi

Mitsubishi FX1N-422-BD Bedienungsanleitung

Mitsubishi

Mitsubishi FX-10GM Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-A A2USHCPU-S1 Bedienungsanleitung

Mitsubishi

Mitsubishi FX3U-485ADP Bedienungsanleitung

Mitsubishi

Mitsubishi A Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Betriebsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Betriebsanleitung

Mitsubishi

Mitsubishi MELSEC-L Series Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC QJ71C24N Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-TC-ADP Bedienungsanleitung

Mitsubishi

Mitsubishi FX0-14 Bedienungsanleitung

Mitsubishi

Mitsubishi MELSEC Q Series Bedienungsanleitung

Mitsubishi

Mitsubishi QD60P8-G Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung