Mitsubishi SR-SDI Bedienungsanleitung

MITSUBISHI COVER GOES HERE

Trademarks and Copyrights—This manual is

1999 by Hughes Network Systems. Software contained in

the digital satellite receiver and referenced in this manual is

Some features are patent pending. WatchWord, PreSelect,

TurboTune, AlphaTune and OneLine Guide are trademarks

of Hughes Network Systems. DIRECTV, DIRECTV PLUS

and DIRECT TICKET are trademarks of DIRECTV, Inc. a

unit of Hughes Electronics Corp., and are used with

permission. “NFL,” the NFL Shield and “NFL SUNDAY

TICKET” are registered trademarks of The National

Football League and its affiliates. “NBA LEAGUE PASS”

is a trademark of NBA Properties, Inc. “NHL,” the NHL

Shield and “NHL CENTER ICE” are registered trademarks

of the National Hockey League. “ESPN Full Court” and

“MLS/ESPN SHOOTOUT” are trademarks of ESPN, Inc.

“MLB,” “MLB EXTRA INNINGS,” “Major League

Baseball” and the Major League Baseball silhouetted batter

logo are service marks of Major League Baseball

Properties, Inc. Major League Baseball trademarks and

Baseball Properties, Inc. All other trademarks and service

marks are the property of their respective owners.

This product is the subject of one or more U.S. or foreign

patentspending.

Disclaimer—Every effort has been made to ensure the

correctness and completeness of the material in this

document. No company shall be liable for errors contained

herein. The information in this document is subject to

change without notice. No warranty of any kind is made

with regard to this material, including, but not limited to,

the implied warranties of merchantability and fitness for a

particular purpose.

StarSight Information—StarSight®features licensed

under one or more of the following U.S. patents: 4,706,121;

5,151,789; 5,335,277; 5,353,121; 5,479,266; 5,479,268;

and 5,532,754. Use rights reserved.

Macrovision Information—This device incorporates an

anticopy process technology that is protected by U.S.

patents and other intellectual property rights. The anticopy

process is licensed for noncommercial, home use only.

Reverse engineering or disassembly is prohibited.

Note on Recording Programming—Mosttelevision

programs and films are copyrighted. This means that

someone has legal rights governing the reproduction and

distribution of this material. In certain circumstances,

copyrighted materials. In most cases, it is permissible to

record for personal use, as long as you do not sell the

material. You must act responsibly in this area — check

into the matter if you are unsure.

Some pay per view programs may be licensed from

producers as “view only” programs. These are copyrighted

programs and may not be copied or reproduced for any

purpose without the express written permission of the

DIRECTV®Programming—For subscription

information, or to resolve problems related to

programming, call the service provider, DIRECTV at

1-800-DIRECTV (347-3288).

Satellite System Hardware and Installation—To

arrange for professional installation of your satellite

system, ask questions, or to resolve problems, contact your

dealer. If additional information is needed, please contact

Mitsubishi Consumer Relations toll free at

1-800-332-2119.

Mitsubishi Consumer Relations

1-800-332-2119

Subscriptions and pay per view

1-800-DIRECTV

PLEASE MAKE NOTE OF THE FOLLOWING

INFORMATION FOR WARRANTY

System Model #: ___________________________

Receiver Model #: SR-SD1

Receiver Serial #: ___________________________

Access Card #: __________ __________ __________

LNB Serial #: ________________________________

IMPORTANT SAFETY INSTRUCTIONS

For your safety and protection, read this entire Owner’s Manual before you attempt to install or use your satellite system. In

particular, read this safety section carefully. Keep this safety information where you can refer to it if necessary.

Heed Warnings—All warnings on the product and in the operating instructions should be adhered to.

Follow Instructions—All operating and use instructions should be followed.

THESE ARE DEFINITIONS FOR ALERTS USED IN THIS MANUAL

WARNING or CAUTION

Where you see this alert symbol

and the WARNING or CAUTION

heading, strictly follow the warning

instructions to avoid personal injury.

DANGER

Electric shock hazard: Where you

see these symbol and the DANGER

heading, strictly follow the warning

instructions to avoid electric shock

injury.

THESE ALERTS APPEAR IN THIS MANUAL

DANGER

Do not select a location to install the satellite

dish antenna near power lines. You can be

killed if the satellite dish antenna comes into

contact with electric power lines.

•Do not contact overhead power lines

•Check the distance to any nearby power

lines before starting installation. Stay at

least 20 feet away from all power lines.

•If any part of the satellite dish antenna or

mast assembly comes into contact with a

power line, call your local power

company. Do not try to remove it

yourself. They will remove it safely.

CAUTION

Local electric codes and the National Electric

Code (NEC) require the satellite dish antenna

to be grounded. Grounding the satellite dish

antenna helps protect against damage caused

by static voltage buildup. Grounding can also

protect against voltage surges created by

nearby lightning strikes.

WARNING

For your own safety, follow these important

safety rules:

•Perform as many functions as possible

on the ground.

•Do not install the satellite dish antenna

on a rainy or windy day.

•If you start to drop the satellite dish

antenna or mast assembly, get away

from it and let it fall.

INSTALLATION

Polarization—This digital satellite receiver is equipped

with a plug that will fit into the power outlet only one way.

Do not modify the plug defeating this feature. If the plug

does not fit, contact your electrician to replace your outlet.

To prevent electric shock, do not use this plug with an

extension cord or outlet unless you can fully insert the

blades without blade exposure.

Power Sources—Operate this digital satellite receiver

only from the type of power source indicated on the

marking label. If you are not sure of the type of power

supply to your home, consult your dealer or local power

company.

Power-Cord Protection—Power-supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, pay

particular attention to cords at plugs, convenience

receptacles, and at the point where they exit from the

product.

Overloading—Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

Ventilation—Slots and openings in the cabinet are

provided for ventilation and to ensure reliable operation of

the product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

For electrical safety, power line operated equipment or

accessories connected to this unit should bear the UL

listing mark should not be modified so as to defeat the

safety features. This will help avoid any potential

hazard from electrical shock or fire. If in doubt, contact

qualified service personnel.

Heat—The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

Accessories—To avoid personal injury or damage to the

digital satellite receiver, do not place the digital satellite

receiver on any unstable cart, stand, table, or bracket. Any

mounting of the product should follow the manufacturer’s

instructions.

Attachments—Do not use attachments unless

recommended by Mitsubishi as they may cause hazards.

Satellite Dish Antenna Grounding—The outdoor

satellite dish antenna used to receive satellite signals and

the cable used to connect the satellite dish antenna to the

indoor receiving unit are required to comply with local

installation codes and the appropriate sections of the

National Electric Code (NEC) and in particular Article 810-

15, which covers proper installation and grounding of

television receiving equipment, as well as to Article 820-

33, which specifies that the satellite dish antenna cable

ground shall be connected to the grounding system of the

building as close to the point of cable entry as practical.

These codes require proper grounding of the metal structure

of the outdoor satellite dish antenna and grounding of the

connecting cable at a point where it enters the house (or

other building). If you are having a professional installer

make the installation, the installer must observe installation

codes. This manual contains instructions on how to make

the installation in compliance with the NEC. If additional

local installation codes apply, contact local inspection

authorities.

EXAMPLE OF ANTENNA GROUNDING ACCORDING

TO THE NATIONAL ELECTRICAL CODE

INSTRUCTIONS CONTAINED IN “RADIO AND

TELEVISION EQUIPMENT”

Water and Moisture— WARNING! To reduce the risk

of fire or electric shock, do not expose this product to rain

or moisture.

Lightning—For added protection for this product during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet,

disconnect the antenna and cable system, and disconnect it

from the telephone line. This will prevent damage to the

product due to lightning and power-line surges.

Television Antenna Information—Installing an

outdoor antenna can be hazardous and should be left to a

professional antenna installer. Do not locate the outside

antenna system in the vicinity of overhead power lines or

other electric light or power circuits, or where it can fall

into such power lines or circuits. When installing an outside

antenna system, take extreme care to keep from touching

such power lines or circuits, as contact with them might be

fatal. If an outside antenna is connected to the digital

satellite receiver, be sure the antenna system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Section 810 of the NEC, NFPA No.

70 1987, provides information with respect to proper

grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of the

grounding conductors, location of antenna discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode.

Note to CATV System Installer—This reminder is

provided to call the CATV system installer’s attention to

Section 820-40 of the NEC which provides guidelines for

proper grounding an, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

Power Lines—Extreme care must be taken when

installing and adjusting or maintaining the outdoor antenna

and connecting cable, especially in the vicinity of overhead

power lines, electric lights, or power circuits. When

installing the outdoor antenna or cable, extreme care should

be taken to keep from touching or approaching such power

lines or circuits, as contact with them might be fatal.

Cleaning—Unplug this digital satellite receiver from the

wall outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

Object and Liquid Entry—Never push objects of any

kind into this digital satellite receiver through openings as

they may touch dangerous voltages or “short out” parts that

could result in a fire or electric shock. Never spill liquid of

any kind on the digital satellite receiver.

SERVICE

Servicing—Do not attempt to service this digital satellite

receiver yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. There

are no user serviceable parts inside. Refer all servicing to

qualified service personnel.

Conditions Requiring Service—Unplug this digital

satellite receiver from the wall outlet and refer servicing to

qualified personnel under the following conditions:

•When the power supply cord or plug is damaged.

•If liquid has been spilled on, or objects have fallen

into, the digital satellite receiver or it has been

exposed to water.

•If the digital satellite receiver does not operate

normally by following the operating instructions.

Adjust only those controls that are covered by the

operating instructions. Other adjustments may result in

damage and will often require extensive work by a

qualified technician to restore the digital satellite

receiver to its normal operation.

•If the digital satellite receiver has been dropped or the

cabinet has been damaged.

•When the digital satellite receiver exhibits a distinct

change in performance.

Replacement Parts—When replacement parts are

required, have the technician verify that the replacements

being used have the same safety characteristics as the

original parts. Use of replacement parts specified by the

manufacturer can prevent fire, electric shock, or other

hazards.

Safety Check—Upon completion of any service or

repairs to this digital satellite receiver, ask the service

technician to perform safety checks recommended by the

manufacturer to determine that the digital satellite receiver

is in safe operating condition.

FEDERAL COMUNICATIONS COMMISSION (FCC)

REGULATORY INFORMATION

Federal Communications Commission (FCC)—

This equipment complies with both Part 15 and Part 68 of

the FCC rules.

Part 15 compliance—

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by removing and applying power

to the equipment, the user is encouraged to try to correct

the interference by one or more of the following measures:

•Reorient or relocate the receiving satellite dish antenna.

•Increase the separation between the equipment and the

digital satellite receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the digital satellite receiver

is connected.

•Consult the dealer or an experienced radio/TV technician

for help.

The user may find the following booklet, prepared by the

Federal Communications Commission, helpful: “How to

Identify and Resolve Radio and TV Interference

Problems.” This booklet is available from the U.S.

Government Printing Office, Washington, DC.

To meet FCC requirements, only peripherals (computer

input/output devices, terminals, printers, etc.) certified to

comply with the Class B limits may be attached to this

device. Operation with non-certified peripherals is likely to

result in interference to radio and TV reception.

To meet FCC requirements, shielded cables are required to

connect the device to a personal computer, peripheral, or

other Class B certified device.

Part 68 compliance—

1. The FCC has established Part 68 of the FCC Rules,

which permit this device to be directly connected to

the telephone network. Standardized jacks are used for

these connections. This equipment should not be used

on coin lines or party lines.

2. If this device is malfunctioning, it may also be causing

harm to the telephone network; this device should be

disconnected until the source of the problem can be

determined and until repair has been made. If this is

not done, the telephone company may temporarily

disconnect service.

3. The telephone company may make changes in its

technical operations and procedures; if such changes

affect the compatibility or use of this device, the

telephone company is required to give adequate notice

of the changes. You will be advised of your right to

file a complaint with the FCC.

4. If the telephone company requests information on

what equipment is connected to their lines, inform

them of:

•the telephone number this unit is connected to.

•the ringer equivalence number (REN). The number

can be found on a label located on the bottom of the

equipment.

•the Universal Service Order Code (USOC) jack

required. This equipment requires a USOC RJ11

jack.

•the FCC registration number. The number can be

found on a label located on the bottom of this

equipment.

TABLE OF CONTENTS

A FIRST LOOK AT THE SATELLITE SYSTEM ........1-1

What You Should Do First.......................................1-1

How Does All This Work?.......................................1-1

SATELLITE SYSTEM COMPONENTS..............................1-2

The Satellite Dish Antenna.......................................1-2

The Digital Satellite Receiver..................................1-2

The Remote Control.................................................1-4

SETTING UP YOUR SATELLITE SYSTEM ...............2-1

INSTALLING REMOTE CONTROL BATTERIES..............2-1

CHOOSING THE BEST CONNECTION FOR YOUR

ENTERTAINMENT SYSTEM...........................................2-2

Hook Up the Audio/S-video Signals.........................2-2

Hook Up the Audio/Video Signals ...........................2-3

Hook Up the RF Signals ..........................................2-3

Hook Up to a Stereo System ....................................2-4

Distributing the Video Signal to Distant Rooms......2-5

Finishing Up............................................................2-5

CONNECTING THE VCR CONTROL CABLE.................2-6

Finding the VCR’s Remote Control Sensor.............2-6

REMOTE CONTROL EXTENDER ...................................2-6

Receiver Base Station Installation...........................2-7

Transmitter Nose Cone Installation.........................2-7

Battery Replacement................................................2-7

Setting the Address of your Digital Satellite Receiver

and Remote Control.................................................2-8

NOW YOU CAN TURN IT ON........................................2-8

CONTROLLING THE DIGITAL SATELLITE

RECEIVER......................................................................3-1

FRONT PANEL VS. REMOTE CONTROL KEYS..............3-1

BASIC NAVIGATION .....................................................3-1

INSTALLING THE SATELLITE DISH ANTENNA …4-1

DETERMINE WHERE TO POINT YOUR SATELLITE DISH

ANTENNA .....................................................................4-2

The INSTALLATION screen....................................4-2

ALIGNMENT RESULT Pop-up Panel.....................4-3

CHOOSING THE ANTENNA INSTALLATION SITE..........4-3

SELECTING AMOUNTING OPTION ..............................4-5

INSTALLING THE SATELLITE DISH ANTENNA ONTO A

WOODEN SURFACE......................................................4-5

Installation Procedure.............................................4-6

INSTALLING THE SATELLITE DISH ANTENNA ONTO A

BRICKSURFACE..........................................................4-7

Installation Procedure.............................................4-8

INSTALLING THE SATELLITE DISH ANTENNA ONTO A

CINDER BLOCK SURFACE............................................4-9

Installation Procedure.............................................4-9

INSTALLING THE SATELLITE DISH ANTENNA ONTO A

METAL POLE..............................................................4-11

Installation Procedure...........................................4-11

ATTACHING THE REFLECTOR ONTO THE LNB SUPPORT

ARM............................................................................4-12

Assembling the Satellite Dish Antenna..................4-12

ATTACHING THE SATELLITE DISH ANTENNA ASSEMBLY

TO THE MAST ORPOLE..............................................4-13

GROUNDING THE METAL POLE MOUNT...................4-14

Installation Procedure...........................................4-14

GROUNDING THE BASE PLATE...................................4-14

Installation Procedure...........................................4-15

INSTALLING AND ROUTING THE LNB COAXIAL CABLE

...................................................................................4-15

Installation Procedure...........................................4-16

CONNECTING THE COAXIAL CABLE TO THE LNB....4-16

Installation Procedure...........................................4-16

ATTACHING THE LNB TO THE LNB SUPPORT ARM.4-17

ROUTING THE LNB CABLE TO THE SATELLITE

RECEIVER...................................................................4-17

CONNECTING THE SATELLITE DISH ANTENNA .........4-17

POSITIONING THE SATELLITE DISH ANTENNA..........4-18

The INSTALLATION Screen..................................4-18

Pointing the Satellite Dish Antenna Using the “Box”

Method...................................................................4-19

AUTHORIZING YOUR SERVICE..................................4-21

WATCHING DIRECTVPROGRAMMING................5-1

BASIC CHANNEL CHANGING .......................................5-1

The Channel Banner ................................................5-1

The Information Banner...........................................5-1

The OneLine™ Guide..............................................5-2

TurboTune™ ...........................................................5-2

AlphaTune™............................................................5-2

ALTERNATE SERVICES.................................................5-3

Audio........................................................................5-3

Digital Audio............................................................5-3

THE ON-SCREEN GUIDES..........................................6-1

Choosing the Guide Style.........................................6-1

Descriptions.............................................................6-2

General On-Screen Guide Features ........................6-2

Using PreSelect........................................................6-3

PreSelecting Programs for Taping..........................6-3

PreSelecting Programs for Viewing........................6-3

Canceling PreSelected Programs............................6-3

THE PROGRAM GUIDE (SM. CELL)....................6-3

THE PROGRAM GUIDE (LG. CELL)....................6-4

THE TITLE GUIDE...................................................6-5

THE LOGO GUIDE....................................................6-6

THE WATCHWORDTM GUIDE .................................6-6

FILTERING THE GUIDES...............................................6-7

Theme Filters...........................................................6-7

Channel List.............................................................6-8

Guide Times.............................................................6-8

Class Filters.............................................................6-8

THE INFORMATION SCREEN .................................6-9

Done.........................................................................6-9

View..........................................................................6-9

PreSelect..................................................................6-9

PreSelect To View..................................................6-10

Cancel PreSelect....................................................6-10

Buy.........................................................................6-10

Buy Options............................................................6-10

Cancel Purchase....................................................6-11

Show Times............................................................6-11

DIGITAL SATELLITE RECEIVER’S MENU SYSTEM

.........................................................................................7-1

Menu Overview........................................................7-1

MAIN MENU.................................................................7-2

Setup.........................................................................7-2

Scheduler..................................................................7-2

Check Mail...............................................................7-2

Purchases.................................................................7-2

Help..........................................................................7-2

Lock/Unlock.............................................................7-2

SETUP MENU................................................................7-3

Preferences ..............................................................7-3

Limits .......................................................................7-3

Chan. Lists...............................................................7-3

TurboTune™ ...........................................................7-3

Installation...............................................................7-3

VCR Setup................................................................7-3

WatchWord..............................................................7-3

Current settings overview........................................7-4

SCHEDULER..................................................................7-4

Editing an event.......................................................7-4

CHECK MAIL...............................................................7-5

Message...................................................................7-5

Page.........................................................................7-5

Erase........................................................................7-5

PURCHASES..................................................................7-5

History/Upcoming....................................................7-6

Purchase History.....................................................7-6

Upcoming Purchases...............................................7-6

LOCK/UNLOCK............................................................7-6

Locking Procedure...................................................7-7

Unlocking Procedure...............................................7-7

Temporarily Overriding the Lock............................7-7

PREFERENCES ..............................................................7-8

Advanced..................................................................7-8

MultiColor................................................................7-8

Chan. Tags...............................................................7-8

Chan. Sort................................................................7-8

Scheme.....................................................................7-8

Audio........................................................................7-8

Language.................................................................7-9

Filters.......................................................................7-9

ADVANCED PREFERENCES...........................................7-9

Receiver ID..............................................................7-9

Screen Ratio.............................................................7-9

Channel Lock...........................................................7-9

Input Key..................................................................7-9

Demo Mode............................................................7-10

Factory Defaults ....................................................7-10

LIMITS........................................................................7-10

TV Timer................................................................7-10

Max Rating.............................................................7-11

Max Spending.........................................................7-11

CHANNEL LISTS .........................................................7-11

Rename...................................................................7-12

Auto Set..................................................................7-12

Clear......................................................................7-12

Set...........................................................................7-12

Tag Boxes...............................................................7-12

TURBOTUNE™..........................................................7-13

Set Channel............................................................7-13

INSTALLATION ...........................................................7-13

System Test.............................................................7-13

New Card...............................................................7-13

Satellite...................................................................7-13

Transponder #.......................................................7-13

Receiver ID............................................................7-14

Dish Type...............................................................7-14

Position..................................................................7-14

SYSTEM TEST.............................................................7-15

Receiver Test..........................................................7-15

Cable Test..............................................................7-15

VCR SETUP...............................................................7-15

Brand.....................................................................7-15

Code.......................................................................7-15

Test (Record/Stop)..................................................7-15

WATCHWORD............................................................7-16

WatchWord #.........................................................7-16

USING D-VHS FEATURES...........................................8-1

CONNECTING THE DIGITAL A/V CABLE.....................8-1

VCR SETUP.................................................................8-1

Recording Type........................................................8-1

Recording Speed......................................................8-2

Test D-VHS Status...................................................8-2

TRANSPORT CONTROLS...............................................8-2

STATUS DISPLAYS ........................................................8-2

Lockout Warnings....................................................8-3

SCHEDULING TO RECORD............................................8-3

CONTROLLING YOUR D-VHS VCR WITH YOUR

REMOTE CONTROL......................................................8-3

PROGRAMMING YOUR REMOTE CONTROL.........9-1

PROGRAMMING THE REMOTE CONTROL....................9-1

Programming Mode.................................................9-1

Code Scan................................................................9-1

Code Entry...............................................................9-1

USING THE REMOTE CONTROL ...................................9-4

Switching the Remote Control to Operate Additional

Digital Satellite Receiver.........................................9-4

Identifying Codes that Have Been Stored................9-4

Controlling Other Components Using the AUX Button

.................................................................................9-5

PAGE 1-1

Congratulations! You’ve selected one of the most advanced digital video and audio components

available today. You now have the capability to receive hundreds of channels of video programming

and CD-quality audio.

What You Should Do First

Your satellite system is both a sophisticated technical product and an easy-to-operate source of

entertainment. You should complete the following steps to achieve the greatest performance from your

system:

•Read this manual to familiarize yourself with the system.

•Install the digitalsatellite receiver.

•Installyour satellite dish antenna and cable.

•Align the satellite dish antenna.

•Arrange for programming from DIRECTV.

•Enjoy endless hours of TV entertainment.

How Does All This Work?

Many film studios, news organizations and other broadcasters (step 1) provide their video, audio, and

data services to the DIRECTV uplink center (step 2).

DIRECTV then digitally transmits the signals 22,300

miles into space to a grouping of high-powered

satellites (step 3) built by Hughes Electronics. These

satellites are located in geostationary orbit. This

means that after installation of the satellite system,

which includes aiming the satellite dish antenna at

the satellites, no adjustment will be necessary to

change channels because everything comes from the

same locations in the sky. The satellite dish antenna

never has to track the satellite, so there's no waiting

for the picture to come in. From the satellites the

digital signals are beamed back to earth where they

are received by your satellite dish antenna (step 4).

The signals then go into the digital satellite receiver

(step 5) where they undergo extensive processing to

determine if you are authorized to access them. The

signals are then reconverted into high-quality video

and audio that you can enjoy on your television. The

telephone connection (step 6) is used by the digital

satellite receiverto report back to DIRECTV (step 7)

any purchase activity.

A FIRST LOOK AT

THE SATELLITE

SYSTEM

The DIRECTV network

MITSUBISHI BRAND DIRECTV PLUS™ DIGITAL SATELLITE RECEIVER

PAGE 1-2

Satellite System Components

There are three main components of a satellite system. They are the satellite dish antenna, the

DIRECTV PLUSdigital satellite receiver, and the remote control. Take a few minutes to read about

each one.

The Satellite Dish Antenna

The satellite dish antenna is the component that receives the digital signals. It must be mounted to a

solid outdoor surface that allows a clear view of the southern sky.

The large dish-shaped part is known as the reflector. Your reflector

may be fairly round (18”) or oval shaped (18” high by 24” wide).

At the end of a tubular arm that is attached to the satellite dish

antenna, there is a low noise block (LNB) assembly. Satellite dish

antennas come in a variety of LNB configurations. Your assembly

may provide for receiving signals from multiple satellites and/or

distributing the signal to one or more satellite receivers.

The mounting bracket and base plate make adjustments easy during

installation. Once the satellite dish antenna has been properly

positioned to point toward the satellites, you should never need to

adjust it again.

Refer to the instructions in Chapter 4, “Installing the Satellite Dish

Antenna” or other satellite dish antenna installation instructions to

determine the type of antenna you have.

The Digital Satellite Receiver

This DIRECTV PLUSdigital satellite receiver is one of the most compact available today. The basic

features for setup, installation, and viewing programming can be accessed from the front panel keys.

Your access card is located behind the door on the right side of the digital satellite receiver. This

special card contains information about your level of service and holds pay per view purchase activity.

This card should not be removed except to protect the digital satellite receiverfrom unauthorized use

or to replace the card when DIRECTV supplies a new one.

The power key ( ) is used to turn the digital satellite receiveron and off. The power light will

illuminate when the unit is on. Any off-air signal, such as cable TV or local programming, connected

to the IN FROM ANT jack is passed through to the OUT TO TVjack when the digital satellite receiver

power is off.

The information key ( ) is used to display descriptions of satellite programs and channels on your

TV screen.

The satellite dish antenna parts. While your dish may

vary in appearance, the components are referred to

using the same names.

The front of the digital satellite receiver and Access Card.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitsubishi Empfänger Handbücher

Mitsubishi

Mitsubishi BD68STB Gebrauchs- und Pflegehandbuch

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung