MO-EL Fiore Benutzerhandbuch

FIORE

Classe I - IP 65

MO-EL S.r.l.

Via Galvani, 18

42027 Montecchio Emilia (RE)

I TA LY

tel +39 (0522) 868011

fax +39 (0522) 864223

www.mo-el.com - [email protected]

HALOGEN QUARTZ INFRARED HEATER

USE AND MAINTENANCE

1. IMPORTANT SAFETY INSTRUCTIONS

Instructions should be carefully read before installation and retained

by the user. The booklet must be keeped and delivered to the new

user in case of cession of the machine. The Manufacturer reserves

the right to vary the features of the product without prior notice. The

technical data are merely indicative.

1. This appliance is intended solely for the use it has been designed

for, namely room and people heating. The Manufacturer is not

responsible for any damage that could happen for improper use.

2. After unpacking make sure that the appliance is complete and

shows no signs of visible damage or tampering.

3. Keep packing materials, which are potential dangers, away from

children.

4. The device can be used by children at least 8 years (as well as by

persons with reduced physical, sensory or mental capabilities, or

lack of experience or required knowledge) provided that they are

under surveillance, or after they have been instructed relating to

the safe use and have understood the potential dangers. Children

should not play with the appliance. Cleaning and maintenance

must be performed by the user and not by unsupervised children.

5. This heating appliance does not feature a device to control ambi-

ent temperature. Do not use it in small rooms used by people

who are unable to leave such rooms on their own unless they are

under constant surveillance.

6. Before inserting the plug make sure that the voltage is the same

as indicated on the device.

7. Do not use in presence of gas, inﬂammable or explosive liquids

or substances.

8. Some fundamental rules which apply to all electrical devices must

be observed when using the heater:

• Do not touch the heather with wet hands.

• Do not handle with bare feet.

• Do not pull the electric cord or the device itself to unplug it

from the socket; pull the plug directly.

EN USE AND MAINTENANCE

9. Avoid the use of an extension cord with this product, because the

extension cord may overheat and cause a risk of ﬁre.

10. Do not apply any modiﬁcation to the product that could compro-

mise the safety.

11. Keep connections dry.

12. If the power supply cord is damaged, avoid to use the appliance.

For power cord replacing, please contact the manufacturer or the

technical service or a person with similar qualiﬁcation, in order to

avoid any risk.

13. If the appliance is not used for a long period, disconnect it from

the power supply.

14. Always unplug the appliance before doing any maintenance op-

eration.

2. ELECTRICAL INSTALLATION

The installation should always be carried out by a qualiﬁed

electrician or a competent person in accordance with the

standards HD 384 CENELEC for Europe, or international IEC

60346-7-708 1988. The energy supply must be done through a prop-

erly grounded socket and the impedance of the electrical network

must be less than 0.3 ohm.

In case of directly connection to supply line an overvoltage category

III bipolar circuit breaker with contact opening distance of at least 3

mm must be ﬁtted upstream from the supply line.

Be careful to connect the heater to a supply line protected by 16 A

fuses not quick-acting type.

• The heaters should always be installed horizontally only using the

mounting brackets provided. This ensures correct positioning and

adequate clearance.

• A minimum air gap of 40 cm should always be allowed between

the top of the heater and a ceiling or roof. The appliance should be

60 cm far from the walls (ﬁg.1).

• A safety distance of not less than 100 cm should always be left in

front of the FIORE heaters or too near.

• This unit should be mounted at a minimum of 180 cm above ground

level (ﬁg.1). If installed in a toilet, the height should be 225 cm in

zone 1 and zone 2; in zone 3 the minimum above ground level is

180 cm, according with the rules of each Country.

• Be sure that the heater is not facing the ceiling or inﬂammable

substances.

• The appliance must not be located neither directly below, nor in

front of a socket-outlet.

• The heater must be installed so as to prevent that the switches can

be touched from those who are in the shower.

• Ensure that there is no possibility of inﬂammable material, com-

bustible material or curtains coming into contact with the heater,

or lie near the heater.

• Heaters should not be installed in areas where hazardous vapours

may be present. Deﬁned in BS5345.

• The heaters are ﬁtted with safety guards. These are intended only

to stop large objects from hitting the emitters. On no account

should the heater be operated with the guard removed.

• For consumer use the heaters are ﬁtted with high temperaure sili-

cone rubber ﬂexible cable (H05 RN-F) conforming to BS 6500.

• The models for professional use, that are marked with a “P” in the

code, do not have the power cord and the switch. For professional

installation, cabling of the same speciﬁcation should be selected.

• The product is in class I and IP65, wich is the protection rate for

the units to be used even outdoor. For keeping the protection rate

of the appliance, the connection of the appliance with the power

supply must be done by means of a minimum IP65 system, as per

the standards HD 384 CENELEC for Europe, or international IEC

60346-7-708 1988.

• Before pressing the switch, seize ﬁrmly the grip and avoid to touch

the metal parts.

3. LOCATION

The Fiore range of heaters is deliberately designed to be very ﬂexible

in the choice of position. There are three basic options:

• A wall mounting bracket version with a speciﬁcally designed

ﬁtting for wall attachment (768M). Before drilling the holes for the

dowels, be sure that the wall is solid and that you are far from wa-

ter tubes or electrical wires. Apply the drilling template on the wall

using adhesive tape and punch in the marked points (see ﬁg.7). For

ﬁxing the appliance at the wall, drill four holes with a 5 mm diam-

eter bit and ﬁx the wall bracket with the dowels and screws that

you ﬁnd in the box (ﬁg.2). Then ﬁx the appliance to the wall bracket

using the 2 screws and the 2 half rings (ﬁg.2). Check that the ar-

rows on the wall bracket are turned up.

• A chain suspended version (768S). Before drilling the holes for

the dowels, be sure that the ceiling is solid and that you are far

from water tubes or electrical wires Fix the buttonhole dowels at

the ceiling at a distance of about 55 cm. Fix the 4 half rings a the

pipe of the appliance, being sure that the chain is ﬁxed with the

screws (ﬁg.3). The 4 half rings should be at the opposite sides of

the pipe, for the best stability. Ensure that the chains are securely

mounted as this application is designed for overhead use.

• A version for mounting on upright (768P). The upright must be

from 20 up to 60 mm in diameter. For ﬁxing it, please see ﬁg. 4.

The upright bracket is studied for holding one appliance or two of

them in opposite position.

Before ﬁxing the appliance on the upright, please ensure that

it is stable and solid. Preferably, use the upright that can be

ordered as accessory (cod. 002473).The feet must be opened

as far as the white evidenced line on the inferior tube reaches the

junction of the feet. Fix the feet to the ground in a proper way, and

then ﬁx the upright to the ground using the chain (ﬁg.5).

Ensure that the supply cable is well mounted and that it does not

come into contact with the reﬂector of the heater or that it does not

trail into the heated area. The supply cable can be ﬁxed to the metal

pipe behind the reﬂector with plastic wrappers.

4. USE

The Fiore range consists of a 1200 W heater and an 1800 W heater.

The essential element of the heater is the halogen ﬁlled quartz linear

lamp with a tungsten element. The heater operates at full output al-

most immediately. The heating reaches a distance of about 3 meters

in front of the appliance.

Avoid exposing skin to the rays of the appliance for distances

less than 50 cm.

Avoid exposing eyes to the rays of the appliance for distances

less than 2.70 m.

All users should be made aware of all aspects of operation and safety

and these instructions should be retained for reference.

Switch on heater (in the models that have the switch) and conﬁrm

that emitter is operating. Ensure that the heater is aiming its warmth

into the target area by adjusting heater angles as necessary by us-

ing the adjustment device on the bracket, after you have loosed the

screws of the half rings (ﬁg.6).

Do not use the heater directly near a bathtub, a shower, a swimming

pool. In unoccupied premises it is recommended that the heating

system is switched off and isolated from the electrical supply.

5. MAINTENANCE

Mo-El Fiore heaters contain no moving parts and therefore very little

maintenance is required other than to ensure that there is no ex-

cessive build-up of dust/dirt on the reﬂectors or emitters as this can

cause overheating and premature emitter failure. To clean the appli-

ance, wipe off with a damp cloth.

The accumulation of limestone or incrustations reduces the life and

the efﬁciency of the lamp; it is suggested therefore to avoid the con-

tinued use in presence of water or salt fog. Eventual leavings of salt

water will have to be removed before the use, after having discon-

nected the appliance, by means of soak in sweet water.

6. EMITTER AND SILICON BUMPERS REPLACEMENT

The emitters used in the Fiore are robust and if knocks and shock

vibrations are avoided, they will last for around 5000 hours. When

changing the lamp, also the silicon bumpers connected with the lamp

must be substituted. They should be substituted even before if there

are signs of aging. Due to the special sealing and anti-shock design

of the heater, the emitters are not intended to be user replaceable.

Please ensure that all emitters are replaced via the Mo-El service

network.

7. TECHNICAL FEATURES

766 767

Power supply 230 V ~ 50-60 Hz 230 V ~ 50-60 Hz

Power 1200 W 1760 W

Insulation Class I I

Protection level IP65 IP65

Lamp Quartz - tungsten wire

Lamp life (hours) 5000 5000

Emission IR-A IR-A

Range (m2)4÷6 8÷10

Weight (kg) 0.95 1

Dimensions (mm) 712x112x83 835x112x83

8. ENVIRONMENTALLY COMPATIBLE DISPOSAL OF THE APPLIANCE

This product conforms to EU Directive 2002/96/EC.

This appliance bears the symbol of the barred waste bin. This indi-

cates that, at the end of its useful life, it must not be disposed of as

domestic waste, but must be taken to a collection centre for waste

electrical and electronic equipment, or returned to a retailer on pur-

chase of a replacement.

It is the user’s responsibility to dispose of this appliance through the

appropriate channels at the end of its useful life. Failure to do so may

incur the penalties established by laws governing waste disposal.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Andere Handbücher für Fiore

Inhaltsverzeichnis

Andere MO-EL Heizung Handbücher

MO-EL

MO-EL SHARKLITE 718 Benutzerhandbuch

MO-EL

MO-EL GIROSOLE Benutzerhandbuch

MO-EL

MO-EL PETALO Series Benutzerhandbuch

MO-EL

MO-EL Girosole 769 Bedienungsanleitung

MO-EL

MO-EL SHARKLITE 712N-712NED Benutzerhandbuch

MO-EL

MO-EL TRIFASE Kurzanleitung

MO-EL

MO-EL AAREN 966V Bedienungsanleitung

MO-EL

MO-EL LUCCIOLA Benutzerhandbuch

MO-EL

MO-EL 791 Benutzerhandbuch

MO-EL

MO-EL 9830ED Benutzerhandbuch

MO-EL

MO-EL PETALO Benutzerhandbuch

MO-EL

MO-EL STILUOVO Benutzerhandbuch

MO-EL

MO-EL PETALO Benutzerhandbuch

MO-EL

MO-EL GUADALUPA Benutzerhandbuch

MO-EL

MO-EL 778R Benutzerhandbuch

MO-EL

MO-EL AMERICAN BAR Benutzerhandbuch

MO-EL

MO-EL 79104 Benutzerhandbuch

MO-EL

MO-EL LUCCIOLA Benutzerhandbuch

MO-EL

MO-EL SHARKLITE Benutzerhandbuch

MO-EL

MO-EL HOT-TOP 9815 Benutzerhandbuch

MO-EL

MO-EL IRIS 866N Benutzerhandbuch

MO-EL

MO-EL BLACKLIGHT Series Benutzerhandbuch

MO-EL

MO-EL Fiore Benutzerhandbuch

MO-EL

MO-EL AAREN 9011 Benutzerhandbuch

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung