MOBA LASERGUIDE MINI Bedienungsanleitung
USER MANUAL
LASERGUIDE MINI
○ R.45.TC.PRO
R.45.TC○
Email
Victoria, Australia
MCE Lasers ® is a registered trademark of MOBA Mobile Automation Australia Pty Ltd
Firmware version: version 0207 R45PRO_V0104_release,
Epping 76, 30
Published y:b
Copyright © Mobile Automation Pty LtdMOBA Australia
All rights reserved. No part of this manual may be reproduced in any form or by any means
without prior written permission from the publishers.
MOBA Mobile Automation Australia Pty Ltd
March 2022
90 Willandra Drive
Document number: OM.R45TC.12
This manual is an important part of your purchase. Please read it thoroughly before using your
new equipment.
Serial number
We recommend that you record details of your purchase here so that the information is readily
available if you ever need to contact your supplier.
Purchased from
Date of purchase
telephone
© Copyright MOBA Mobile Automation Australia Pty Ltd
MCE Lasers was acquired by MOBA in 2018,
bringing 40 years of Australian development and
manufacturing together with MOBA’s globally
recognised and trusted expertise in mobile
automation technology.
2Imprint
STATEMENT OF LIMITED WARRANTY
MOBA Mobile Automation Australia Pty Ltd (MOBA Australia) warrants all equipment it
manufactures and sells to be free of defects in material and workmanship for a period
specified below. This warranty period is from the date of sales invoice. All other components
not manufactured by MOBA Australia and not specified below, such as hydraulic or electrical
components, hoses, fittings and clamps, will carry the original manufacturer's warranty. The
warranty covers only equipment sold by MOBA Australia and it's authorised dealers and does
not cover parallel imports, which are also known as grey or direct imports. Proof of purchase
will be required before claiming warranty.
Warranty period:
The foregoing states the entire liability of MOBA Australia regarding the purchase and use of
its equipment. MOBA Australia will not be held responsible for any consequential loss or
damage of any kind.
MOBA Australia or its authorised service centre will repair or replace, at its option, any
defective part or component of which notice has been given during the warranty period. If
service in the field is necessary to repair machine-mounted equipment under warranty, MOBA
Australia may authorize on-site repairs at no charge for parts and labour. Travel time,
accommodation and other expenses incurred to and from the place where repairs are made
will be charged to the purchaser at the prevailing rates. If warranty service can be done at a
factory authorised service centre, the customer will pay only one-way freight charges.
This warranty is in lieu of all other warranties, expressed or implied, except as set forth above,
including any implied warranty of merchantability or fitness for a particular purpose which are
hereby disclaimed.
The warranty does not cover normal wear and tear or deterioration. Any evidence of
negligence or abnormal use, accident, improper installation or an attempt to repair equipment
by anyone other than factory authorised personnel even when using MOBA Australia's certified
or recommended parts, automatically voids the warranty.
The warranty shall only be in force for the benefit of the Purchaser, not any third parties,
including without limitation the Purchaser's customers, unless warranty transfer has been
approved by MOBA Australia in writing
Warranty
© Copyright MOBA Mobile Automation Australia Pty Ltd
3
Products
Laser receiving systems and components, visual guidance
Warranty (months)
12
operator.
on the machine.
not running. When working on or near hydraulic lines, protect yourself at all
Warning:
prevent the Laserguide from vibrating excessively or from breaking at the
All mounting bracket welds must be strong and secure enough so as to
operation. It is best to remove any electronic gear near a welding job.
your machine, including safety information, before installing or using your
times and wear protective clothing.
1 Read and become familiar with the manufacturer's operating manual for
adjust the unit while your machine is running.
SAFETY INFORMATION
caution when on a construction site.
3 The Laserguide is externally mounted on your machine. Do not install or
4 Do not let any part of the unit protrude into traffic or limit the visibility of the
2 A construction site can be hazardous and working around heavy
Laserguide receiver.
construction equipment can be dangerous. Always exercise extreme
Please become familiar with the important safety information in this section. Improper use or
installation of the MOBA Laserguide may result in personal injury or damage to the receiver
unit.
5 Always use eye protection when welding, cutting or grinding is being done
6 Hydraulic lines can be under extreme pressure, even when the machine is
Do not weld near any hydraulic line or on any equipment while it is in
Caution:
weld while the machine is operating
© Copyright MOBA Mobile Automation Australia Pty Ltd
Safety Information
4
Table of Contents
© Copyright MOBA Mobile Automation Australia Pty Ltd
2.1 Powering Up ......................................................................................................................8
2.6 LED Brightness ................................................................................................................13
3.1 Communicating with the MCE.R45APP ...........................................................................14
3.3 Configuring BT on DB.UNI.PRO ......................................................................................16
5. Using the DB.UNI.PRO and ANDROID APP-Optional (R.45.TC.PRO only)............................20
2.3 Compensation Range ......................................................................................................12
2.2.2 Setting Up With Tilt Compensation Off ....................................................................11
2.2 Mounting And Setting Up ....................................................................................................8
2.5 Buzzer .............................................................................................................................12
4. CAN Connectivity Setup - Optional (R.45.TC.PRO only) ........................................................17
2. Using the Laserguide ...............................................................................................................8
3. BT Connectivity Setup - Optional (R.45.TC.PRO only) ...........................................................14
1. Features of the Laserguide ......................................................................................................6
2.2.1 Setting Up With Tilt Compensation On ...................................................................10
2.4 Accuracy (Centre Band) ...................................................................................................12
2.7 Low Battery Warning ........................................................................................................13
3.2 Communicating with the DB.UNI.PRO .............................................................................15
4.1 Connecting to the DB.UNI.PRO display panel ..................................................................17
4.2 Connecting to the MOBA XSITE 2D excavator range .......................................................18
6. Technical Specifications ........................................................................................................22
7. Declaration of Conformity ......................................................................................................23
5.2 ANDROID APP ................................................................................................................21
5.1 DB.UNI.PRO ...................................................................................................................20
5
CONTENTS
1. FEATURES OF THE LASERGUIDE
1. Magnetic Bracket
2. Receiving Area
3. Top LED Cluster (RED)
4. Centre LED Cluster (GREEN)
5. Power On LED
6. Mounting Reference Mark
7. Bottom LED Cluster (ORANGE)
8. Accuracy Switch (Centre Band)
9. Reference Dial
10. On/Off Switch
11. Battery Compartment (Holding Handle)
12. Battery Cap
13. Magnetic Bracket Protective Plate
2
1
3
9
8
10
4
6
13
7
5
11
12
Features
© Copyright MOBA Mobile Automation Australia Pty Ltd
Figure 1
6
R.45.TC
0.25
0.5
2.5 [m]
2.0
1.5
1.0
OFF
1. Magnetic Bracket
2. Receiving Area
3. Top LED Cluster (RED)
4. Centre LED Cluster (GREEN)
5. Power On LED
6. Mounting Reference Mark
7. Bottom LED Cluster (ORANGE)
8. Accuracy Switch (Centre Band)
9. Reference Dial
10. On/Off Switch
11. CAN Connectors
12. Battery Cap
13. Dismounting Lever
14. Magnetic Bracket Protective Plate
2
5
6
11
13
12
1
3
4
7
9
8
10
Features
© Copyright MOBA Mobile Automation Australia Pty Ltd
R.45.TC.PRO
Figure 2
7
0.25
0.5
2.5 [m]
2.0
1.5
1.0
OFF
0.25
0.5
2.5 [m]
2.0
1.5
1.0
OFF
MT.
REF
14
Press the On/Off switch (10) for 2 seconds to turn the unit on/off. The small red power-on
LED (5) indicates the mode of operation as determined by the Reference Dial (9) position:
2.1 Powering Up
LED flashing – Tilt compensation feature is on. The unit automatically accounts for the
dipper arm tilt to indicate correct digging depth. Reference Dial (9) not in Off position.
LED solid – Tilt compensation feature is off. The unit does not account for the dipper arm
tilt when indicating correct digging depth. This mode is less accurate. Reference Dial (9) in
Off position.
On power up, the sensor will do an LED test sequence, activating in turn the red, green
and amber LEDs. It will then show the current accuracy selection by briefly flashing the
appropriate LED pattern (see section 2.4).
2.2 Mounting and Setting Up
2. USING THE LASERGUIDE
© Copyright MOBA Mobile Automation Australia Pty Ltd
Using the Laserguide
8
IN-TRENCH SETUP
Figure 3
Using the Laserguide
© Copyright MOBA Mobile Automation Australia Pty Ltd
9
compensation).
R.45.TC/R.45.TC.PRO magnetic bracket (relevant only when using tilt
With regard to Figures 3 & 4 refer to section 2.2.1 if intending to use the tilt
compensation feature or to section 2.2.2 if intending NOT to use the tilt compensation
feature.
Setup Length - Distance from bucket pivot pin to 'MT REF' line mark on the side of the
B - Bucket height from bucket pivot pin to ground when the bucket is level
L - Height of the laser instrument referenced to the bottom of the trench.
C - Desired depth of cut or excavation referenced to the benchmark.
HI - Height of the laser instrument referenced to the benchmark.
OUT-TRENCH SETUP
Figure 4
© Copyright MOBA Mobile Automation Australia Pty Ltd
Using the Laserguide
10
L = HI + C
2. Set up the laser instrument on a steady tripod.
2.2.1 Setting Up With Tilt Compensation On
4. Determine the Setup Length by measuring the distance between the bucket pivot pin
and the ‘MT REF’ line on the magnetic bracket. This is the same as the mounting
distance L minus the bucket height B:
The Setup Length should lie within the R.45.TC/R.45.TC.PRO’s working range of 0.25-
2.5m. If it is outside of this range, lower or raise the height of the laser instrument (HI)
and readjust the R.45.TC/R.45.TC.PRO mounting position to bring it within range.
5. Turn the Reference Dial (9) to the measured Setup Length value or to the closest
available value.
3. Mount the R.45.TC /R.45.TC.PRO on the dipper arm such that the ‘MT REF’
(Mounting Reference) line mark on the side of the magnetic bracket is at a distance L
from the ground. Distance L equals the height of the laser instrument (HI) plus the
desired depth of excavation (C), both with respect to the benchmark:
6. 'Zero' the setup position by pressing and holding together the Accuracy (8) and
On/Off (10) switches. A successful 'zeroing' is acknowledged by a brief flashing of the
green LED cluster and sounding of the buzzer. An unsuccessful attempt is indicated by
a brief flashing together of the red and amber LED clusters. A failed attempt can be
caused if the R.45.TC/R.45.TC.PRO is angled too far from the vertical or if the
Reference Dial (9) is in the off position.
The long side of the R.45.TC /R.45.TC.PRO body should be parallel with the dipper arm
and in line with the top and bucket pivot pins of the dipper arm. The switchpad should
be orientated to the bottom.
1. Ensure the dipper arm is vertical and the bucket is level.
Setup Length = L - B
For best accuracy, the Setup Length should coincide with one of the selectable values
on the dial, that is, 0.25m, 0.5m, 0.75m, 1m, 1.25m, 1.5m, 1.75m, 2m, 2.25m or 2.5m.
For most applications, a Setup Length as close as possible to one of these values is
adequate.
= HI + C - B
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere MOBA Messgerät Handbücher
