molex 207129 Series Bedienungsanleitung
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 1 of 8
Revision: C Revision Date: 09-07-10
CONDUCTOR
BRUSH
STRIP LENGTH
SEAM
CONDUCTOR
CRIMP
CUT-OFF
TAB
BELL MOUTH BEND UP
TWISTING
RO
L
BEND
DOWN
WIRE
WIRE
ANGLE
Application Tooling
Sp cification Sh t
Tool Kit
Ord r No. 63811-5370
Hand Crimp Tool
Ord r No. 63811-5300
FEATURES
% A full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
Tool kits are easily installed into the Hand Crimp Tool or the 6 816-0 00 Power Crimp Head which is installed
into the 6 816-0200 (110 V) or the 6 816-0250 (220 V) Battery Powered Tool.
Many different Tool kits can be used with a single Battery Powered Tool.
This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.
SCOPE
Products: MX150L™10-12 AWG
T rminal S ri s No.
T rminal Ord r No. Wir Siz Insulation Diam t r Strip L ngth
Loos Pi c
R l AWG
mm² mm In. mm In.
194 1 194 1-0016 194 1-0001
10-12
5.26- . 1
.90-4.85
.15 -.191
5.50-6.20
.217-.244
194 4 194 4-000 194 4-0001
10-12
5.26- . 1
.90-4.85
.15 -.191
5.50-6.20
.217-.244
Customer to cut off terminal from reel: 0.50mm (.020”) maximum Cut-off Tab.
DEFINITION OF TERMS
TYPE 4C
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 2 of 8
Revision: C Revision Date: 09-07-10
SWING
LOCATOR
OPEN
PRESS DOWN
ON THE BRASS
PIVOT SHAFT
LIFT UP ON
THE LOCATOR
Figur 2
ANVILS
POWER
CRIMP
HEAD
Figur 1
PUNCHES
M4 X 10 LONG
BHCS
M4 X 18 LONG
BHCS
CRIMP SPECIFICATION
T rminal S ri s No. B ll Mouth B nd up B nd down Twist Roll Conductor Brush Wir Angl
mm In. D gr D gr mm In. D gr
194 1 0.25-1.25
.010-.049
2 4 8 0.10-0.50
.004-.020
5° Max
194 4 0.25-1.25
.010-.049
2 4 8 0.10-0.50
.004-.020
5° Max
S am: Seam shall not be open and no wire allowed out of the crimping area.
CONDITIONS:
After crimping, the conductor profiles should measure the following (See notes on page 4).
T rminal
S ri s No.
Wir Siz
Conductor Insulation Pull Forc
Minimum
Crimp H ight (R f)
Crimp Width (R f) Crimp H ight (R f)
Crimp Width (R f)
AWG
mm2
mm In. mm In. mm In. mm In. N Lb.
194 1 10 5.26
2.45-2.55
.096-.100
.70- .90
.146-.154
5.00 Max
.197 Max
5.10-5. 0
.201-.209
56.0
80.0
12 . 1
2.05-2.15
.081-.085
.70- .90
.146-.154
4.50 Max
.177 Max
5.00-5.20
.197-.205
11.5
70.0
194 4 10 5.26
2.45-2.55
.096-.100
.70- .90
.146-.154
5.00 Max
.197 Max
5.10-5. 0
.201-.209
56.0
80.0
12 . 1
2.05-2.15
.081-.085
.70- .90
.146-.154
4.50 Max
.177 Max
5.00-5.20
.197-.205
11.5
70.0
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage
can occur to the tool or die.
INSTALLATION
To install the Tool Kit into the Power Crimp Head follow the steps below:
Anvils and Punch s Installation
1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 10 long BHCS and tighten in place.
2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long BHCS and tighten in place. See
Figure 1.
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page of 8
Revision: C Revision Date: 09-07-10
Locator Installation and R moval
Follow the steps below to install or replace the locator. See Figure 2.
To install th locator
1. Position the locator with the hole over the brass pivot
shaft and snap it into place.
To r mov th locator
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the
hand tool.
. Firmly press down on the brass pivot shaft with your
thumb, while pulling the locator up. Slip the locator
off the top of the brass pivot shaft.
OPERATION
Open the tool by squeezing the handles together, at the
end of the closing stroke, the ratchet mechanism will release the handles, and the hand tool will spring open.
Crimping T rminals
Swing the terminal locator against the crimp tool and turn the lock up to lock the locator. Terminals can be loaded
easily while the locator is against the crimp tool and locked. The spring-loaded locator needs to be in the up
position for terminals to load easily.
1. To raise the wire stop, press the tab on the wire stop as shown in Figure . Insert the proper terminal into the
nest opening and release the wire stop to lower it.
2. Insert the proper pre-striped wire over the terminal. Gently touch the wire stop with the end of the wire. See
Figure 4 and 5.
. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.
Release handles to open the jaws.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
HANDLE
OPEN
LOCK IN
UP RIGHT
POSITION
LOCATOR
CLOSED
Figur 3
TERMINAL
PUSH HERE TO
OPEN WIRE STOP
Figur 4
WIRE IN TERMINAL
JAWS
PARTIALLY
CLOSED
WIRE AGAINST
WIRE STOP
LOCATOR ANVIL
TERMINAL
WIRE
PUNCH
WIRE AGAINST STOP
Figur 5
WIRE STOP
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 4 of 8
Revision: C Revision Date: 09-07-10
4. Remove the crimp terminal from the terminal locator by pressing the tab on the wire stop and gently pulling on
the wire.
5. Visually inspect the crimped terminal for proper crimp location and crimp height.
For th Batt ry Pow r Tool:
1. Cycle the Battery Power Tool to crimp the terminal to the wire.
2. Remove the crimped terminal from the terminal locator by pressing down on
the wire stop and gently pulling on the wire. The terminal locator can be in
either position.
. Visually inspect the crimped terminal for proper crimp location.
Not :
A crimp height chart is provided with this manual as Reference Only. Due to the
wide range of wires, strands, insulation diameters, and durometers, actual crimp
height measurements may very slightly. An occasional, destructive, pull force test
should be preformed to check hand tool crimp. Pull Force value must exceed the
minimum pull force specifications listed.
Maint nanc
It is recommended that each operator of the tool be made aware of,
and responsible for, the following maintenance steps:
1. Remove dust, moisture and other contaminants with a clean
brush, or soft, lint-free cloth.
2. Do not use any abrasive materials that could damage the tool.
. Make certain all pins; pivot points and bearing surfaces in the
tool head are protected with a thin coat of high quality machine
oil. Do not oil excessively. This tool was engineered for
durability, but like any fine piece of equipment, it needs
cleaning and lubrication for a maximum service life of trouble-
free crimping. The use of light oil, such as 0 weight
automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life and ensure a stable
calibration. See Figure 6A or 6B for lubrication points.
4. Store the tool in a clean and dry area when not in use.
Miscrimps or Jams for Crimp Hand Tools Only
(S Figur 9)
Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or
closed. The tool will open easily by rotating the small slotted screw marked with an arrow. See Figure 9.
Warranty
This tool kit is for electrical terminal crimping purposes only. This tool kit is made of the best quality materials. All
vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 0
days. Should such a defect occur, we will repair or exchange the tool kit free of charge. This repair or exchange
will not be applicable to altered, misused, or damaged tools.
LUBRICATION
POINTS
(BOTH SIDES)
LIGHT OIL
(EVERY MONTH
OR
5,000 CRIMPS)
Figur 6A
LUBRICATION POINTS
(BOTH SIDES) LIGHT OIL
(EVERY 3 MONTHS OR
5,000 CRIMPS)
Figur 6B
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 5 of 8
Revision: C Revision Date: 09-07-10
Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
CAUTION: Repetitive use of this tool should be avoided.
C rtification
Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for
customers to re-certify hand tools.
% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
% This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 6 of 8
Revision: C Revision Date: 09-07-10
The chart below shows all applications for this Tool Kit.
Tool Kit
Ord r No.
Tool
Ord r no.
Tool
D scription
Pow r H ad
Ord r No.
Adapt r
D scription
Figur
No.
6 811-5 70
6 810-1050
Hand Crimp Frame (Short) N/A N/A 7
6 810-1000
Hand Crimp Frame (Long) N/A N/A 7
6 816-0200
Battery Power Tool (110 V)
6 816-0 00 Power Crimp Head
8
6 816-0250
Battery Power Tool (220 V)
6 816-0 00 Power Crimp Head
8
Applications for th Tool Kit
Hand Crimp Tool Batt ry Pow r d Tool
Figur 7 Figur 8
WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper
instruction and without first reading and understanding the instructions in the proper Manual or
Specification Sheet. See Chart above for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the
power is turned off.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
POWER
CRIMP
HEAD
LOCKING PINS
BATTERY
POWERED
TOOL
TOOLING KIT
HAND CRIMP
FRAME LONG
AND SHORT
TOOLING KIT
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 7 of 8
Revision: C Revision Date: 09-07-10
RATCHET
RELEASE SCREW
Figur 9
M4 X 8mm
LONG BHCS
2
1
3
M4 X 18mm
LONG BHCS
M4 X 10mm
LONG BHCS
2
4
WITH TOOL KIT
LOCATOR ONLY
HAND TOOL PARTS LIST
It m Numb r Ord r Numb r D scription Quantity
1 6 810-1000 Hand Crimp Frame (Long) 1
2 6 811-5 70 Tool Kit with Locator 1
6 811-477 Locator Base 1
4 6 811-5 75 Locator (only) REF
Tool Kit for MLX150L™ Crimp Terminals
Doc No: ATS-6 8115 HM Release Date: 04-29-05 UNCONTROLLED COPY Page 8 of 8
Revision: C Revision Date: 09-07-10
Figur 10
1
2
2
M4 by 8 Long
BHCS
M4 by 18 Long
BHCS
M4 by 10 Long
BHCS
1
POWER HEAD PARTS LIST
It m Ord r No Engin ring No. D scription Quantity
1
6 816-0 00 6 816-0 00 Power Crimp Head 1
2
6 811-5 70 6 811-5 70 Tool Kit 1
http://www.molex.com
Andere Handbücher für 207129 Series
100
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere molex Crimpwerkzeuge Handbücher
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63811-5300 Bedienungsanleitung
molex
molex 63825-0500 Bedienungsanleitung
molex
molex 63823-4500 Benutzerhandbuch
molex
molex 63823-5200 Bedienungsanleitung
molex
molex 63819-3500 Bedienungsanleitung
molex
molex 63816-0200 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63825-1670 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63825-3000 Bedienungsanleitung
molex
molex AT-1300 Bedienungsanleitung
molex
molex MV-396 Benutzerhandbuch
molex
molex 207129 Series Bedienungsanleitung
molex
molex 64005-6200 Bedienungsanleitung
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Panduit
Panduit CT-1000 Administratorhandbuch
JST
JST CS 10 Bedienungsanleitung
Danfoss
Danfoss ET4200 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
TE Connectivity
TE Connectivity 2063528-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics 69156-1 Bedienungsanleitung
Textron
Textron ESG105L Bedienungsanleitung
Tyco Electronics
Tyco Electronics 90035-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung