molex CR60622B Bedienungsanleitung
CR60622B Hand Crimp Tool for “Mini-Fit” Jr. Terminals
Doc No. 11-01-0197 Release Date: 04-08-93 UNCONTROLLED COPY Page 1 of 5
Revision: F Revision Date: 09-01-05
INSULATION
CRIMP
BRUSH
STRIP
LENGTH
BELL MOUTH
CRIMP HEIGHT
BEND
DOWN
BEND UP
ROLLING
CONDUCTOR
CRIMP
TWISTING
HAND CRIMP TOOL
Operating Instruction and
Specification Sheet
Order No. 11-01-0197
(CR60622B)
FEATURES
Small handle spread which make this style tool ideally suited for end users
Ratchet with safety release that ensures consistent performance
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
SCOPE
Wire Size Insulation Diameter Strip Length
Terminal Series No. AWG mm² mm In. mm In.
5556T 18 - 24 0.80-0.20 1.30-3.10 .051-.122 3.00-3.50 .118-.138
5558T 18 - 24 0.80-0.20 1.30-3.10 .051-.122 3.00-3.50 .118-.138
30490 18 - 24 0.80-0.20 1.30-3.10 .051-.122 3.00-3.50 .118-.138
44476-1 18 - 24 0.80-0.20 1.30-3.10 .051-.122 3.00-3.50 .118-.138
44478-1 18 - 24 0.80-0.20 1.30-3.10 .051-.122 3.00-3.50 .118-.138
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.
CR60622B Hand Crimp Tool for “Mini-Fit”Jr. Terminals
Doc No. 11-01-0197 Release Date: 04-08-93 UNCONTROLLED COPY Page 2 of 5
Revision: F Revision Date: 09-01-05
CONDITIONS:
After crimping, the conductor profiles should measure the following (see notes on page 4).
Wire Size Cond. Crimp
Height (Ref)
Punch Width Cond.
(Ref) Pull Force Min. Profile
Terminal Series No.
AWG mm2mm In. mm In. N Lb. A B
5556T 18 0.80 1.12-1.22 .044-.048 1.61 .063 89.0 20.00 X
5556T 20 0.50 0.79-0.89 .031-.035 1.61 .063 57.8 13.00 X
5556T 22 0.35 0.79-0.89 .031-.035 1.61 .063 40.0 9.00 X
5556T 24 0.20 0.79-0.89 .031-.035 1.61 .063 31.1 7.00 X
5558T 18 0.80 1.12-1.22 .044-.048 1.61 .063 89.0 20.00 X
5558T 20 0.50 0.79-0.89 .031-.035 1.61 .063 57.8 13.00 X
5558T 22 0.35 0.79-0.89 .031-.035 1.61 .063 40.0 9.00 X
5558T 24 0.20 0.79-0.89 .031-.035 1.61 .063 31.1 7.00 X
30490 18 0.80 1.12-1.22 .044-.048 1.61 .063 89.0 20.00 X
30490 20 0.50 0.79-0.89 .031-.035 1.61 .063 57.8 13.00 X
30490 22 0.35 0.79-0.89 .031-.035 1.61 .063 40.0 9.00 X
30490 24 0.20 0.79-0.89 .031-.035 1.61 .063 31.1 7.00 X
44476-1 18 0.80 1.12-1.22 .044-.048 1.61 .063 68.5 15.40 X
44476-1 20 0.50 0.79-0.89 .031-.035 1.61 .063 57.8 13.00 X
44476-1 22 0.35 0.79-0.89 .031-.035 1.61 .063 40.0 9.00 X
44476-1 24 0.20 0.79-0.89 .031-.035 1.61 .063 31.1 7.00 X
44478-1 18 0.80 1.12-1.22 .044-.048 1.61 .063 68.5 15.40 X
44478-1 20 0.50 0.79-0.89 .031-.035 1.61 .063 57.8 13.00 X
44478-1 22 0.35 0.79-0.89 .031-.035 1.61 .063 40.0 9.00 X
44478-1 24 0.20 0.79-0.89 .031-.035 1.61 .063 31.1 7.00 X
CR60622B Hand Crimp Tool for “Mini-Fit”Jr. Terminals
Doc No. 11-01-0197 Release Date: 04-08-93 UNCONTROLLED COPY Page 3 of 5
Revision: F Revision Date: 09-01-05
OPERATION
Open the tool by squeezing the handles together, at the end of the closing stroke, the
ratchet mechanism will release the handles, and the hand tool will spring open.
Crimping Terminals
1. Lift the locator blade and place the terminal into the correct die profile (A or B),
release the locator blade. Not all tools are equipped with a locator or locator
blade.
2. Partially close the tool until the terminal is held in place,
(See Figure 1). If the insulation diameter is too large to
do this, then place the insulation down into the terminal
before closing the tool.
3. Place a wire into the terminal and up against the locator
blade, (See Figure 2). On tools without locators line the
wire up with the conductor and insulation grips visually.
4. Close the tool until the ratchet releases, (See Figure 3).
5. Lift the locator blade or wire stop up.
6. Carefully remove the crimped terminal.
Maintenance
It is recommended that each operator of the tool be made aware of, and responsible
for, the following maintenance steps:
1. Remove dust, moisture and other contaminants with a clean brush, or soft, lint
free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin
coat of high quality machine oil. Do not oil excessively.
4. When tool is not in use, keep the handles closed to prevent objects from
becoming lodged in the crimping dies, and store the tool in a clean, dry area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open
easily by lifting the ratchet release lever (See Figure 4).
Figure 2
Figure 3
TERMINAL
PRE-STRIPPED WIRE
Figure 1
CR60622B Hand Crimp Tool for “Mini-Fit”Jr. Terminals
Doc No. 11-01-0197 Release Date: 04-08-93 UNCONTROLLED COPY Page 4 of 5
Revision: F Revision Date: 09-01-05
How To Adjust Tool Crimp Force (See Figure 4)
It may be necessary over the life of the tool to adjust tool-crimping force. Listed below are the steps required to adjust the crimping force
of the hand tool to obtain proper crimp conditions:
1. Remove the screw and washer. Located over the adjustment ring.
2. Lift the adjusting ring slightly, off of the locating pin.
3. Turn the adjusting ring in the desired direction (L= less force, T= more force) to increase or decrease crimp pressure.
4. Press the adjusting wheel flat against the tool and engage the locking pin.
5. Replace the washer and screw.
6. Check the crimp specifications after tool crimp force is adjusted.
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long
life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we would
exchange the tool free of charge. This will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use
only. Any clamping, fixturing, or use of handle extensions voids this warranty.
Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.
CAUTION: Repetitive use of this tool should be avoided.
Notes:
1. This tool should only be used for the terminals and wire gauges specified on this sheet.
2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above). Variations in tools,
terminals, wire stranding and insulation types may affect crimp height.
3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes.
4. Molex does not repair hand tools (see warranty above) The replacement parts listed are the only parts available for repair. If the
handles or crimp tooling is damaged or worn, a new tool must be purchased.
5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the
insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire
insulation or the conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping
and crimp testing.
6. Molex does not certify crimp hand tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.
CR60622B Hand Crimp Tool for “Mini-Fit”Jr. Terminals
Doc No. 11-01-0197 Release Date: 04-08-93 UNCONTROLLED COPY Page 5 of 5
Revision: F Revision Date: 09-01-05
M4 NUT
RATCHET
RELEASE LEVER
ADJUSTMENT
RING
LOCATOR
BLADE
2
1
M4 X 18LG BHCS
3
PARTS LIST
Item Number Order Number Description Quantity
1 11-11-0377 Locator Assembly** 1
2 11-11-0324 Spring (Main) 1
3 11-11-0320 Spring (Ratchet) 1
** Not all tools are equipped with a locator or locator blade.
Molex Application Tooling Group
1150 E. Diehl Road
Naperville, IL, 60563
Tel: 630-969-4550
Fax: 630-505-0049
Visit our Web site at http://www.molex.com
Figure 4
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere molex Crimpwerkzeuge Handbücher
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 59354 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63823-7570 Bedienungsanleitung
molex
molex 63825-3000 Bedienungsanleitung
molex
molex 213309-1400 Bedienungsanleitung
molex
molex 78172 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63827-5000 Bedienungsanleitung
molex
molex RHT-4753 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 63813-2100 Bedienungsanleitung
molex
molex 207129 Series Bedienungsanleitung
molex
molex 50098 Series Bedienungsanleitung
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Panduit
Panduit CT-1000 Administratorhandbuch
JST
JST CS 10 Bedienungsanleitung
Danfoss
Danfoss ET4200 Bedienungsanleitung
Tyco Electronics
Tyco Electronics PRO-CRIMPER III Bedienungsanleitung
TE Connectivity
TE Connectivity 2063528-1 Bedienungsanleitung
Tyco Electronics
Tyco Electronics 69156-1 Bedienungsanleitung
Textron
Textron ESG105L Bedienungsanleitung
Tyco Electronics
Tyco Electronics 90035-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Bedienungsanleitung
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Bedienungsanleitung