Mongoose M8 Bedienungsanleitung
Model number: M8
&
M824
VEHICLE ALARM SYSTEM
Owner’s Operation/Installation Manual
Please read and try out all the features
For correct operation and warranty compliance,
we recommend professional installation of this
product by your authorised Mongoose dealer.
M8 Suitable for 12volt, negative ground vehicles
M824 Suitable for 24volt, negative ground vehicles
Congratulations on your purchase of this state-of-the-art Mongoose security system.
To fully appreciate the many functions and safeguards incorporated in this system, please spend a few
minutes reading this manual.
You may find unexpected features that could mean the difference between “protected” and “fully protected”.
FEATURES:
2 x 3 Button Remote Controls
Code Learning –Code Hopping Remotes (capable of accepting 4)
Bonnet, Boot & Door Protection
Engine Immobiliser
On-Board Adjustable Shock Sensor
Electronic Siren
Remote Panic
Valet Mode
Park Light Flash
7 Function Hyper Blue LED - Arm / Disarm / 3 Zone Reporting / Valet / Arming
Intrusion Alert with Memory
Audible Arm / Disarm / Defective Zone / Tamper Confirmation
Ignition Door Lock/Unlock - Programmable
Chirps (Arm/Disarm) Defeat –Programmable
Automatic Last Door Arming –Programmable
Automatic Door Lock - Programmable
Defective Zone By-Pass
BUTTON1
‘ARM’ (& LOCK)
PRESSFOR1.5SECONDS
PANIC
PRESS FOR 3 SECONDS
BUTTON2
‘DISARM’ (& UNLOCK)
PRESS FOR 1.5 SECONDS
BUTTON 3
BOOT RELEASE
(If vehicle equipped)
CANCEL‘PANIC’
ALARM REMOTE CONTROL –2 supplied
OPERATING YOUR VEHICLE SECURITY SYSTEM
ARMING (& LOCKING*)
Turn off the engine, exit the vehicle and close all doors, bonnet and boot.
REMOTE- Press and release the ‘Arm (Lock)’ button on the keychain transmitter. The siren will "chirp"
once, the
vehicle's parking lights will flash once, the doors will lock (optional), and the dash mounted LED will begin
to slow flash.
WARNING! Excessive pressure on the transmitter buttons will damage the internal components on the
circuit board. All that is required is a light push to the button.
DEFECTIVE ZONE BYPASS
1. If the siren "chirped" three times when ‘Armed’, then one of the entry points (bonnet, boot, doors)
has been left open. Closing the open circuit will correct the problem.
2. If the siren "chirped" three times, sometime after arming, the exclusive delayed domelight learn
circuit has been programmed and the system detected a open entry point after the learned delay
expired. Again, closing the circuit will correct the problem and you do not need to disarm the system to
make the correction.
LAST DOOR AUTO ARM *PROGRAMABLE
Turn off the engine, exit the vehicle and close all doors, bonnet and boot.
The Dash LED will begin to flash rapidly, indicating that the system is automatically (passive) arming.
Passive arming will not begin till after all doors and boot are closed.
In 30 seconds, you will hear a single short “chirp” from the siren and the vehicle and the vehicle parking
lights will flash once indicating the system is now armed. The LED will begin to flash slowly indicating the
system is fully armed.
Opening a door will suspend the automatic arming sequence.
If you wish to arm the system immediately, simply press the ARM button on the keychain transmitter.
DISARMING (& UNLOCKING*)
As you approach the vehicle, press and release the ‘Disarm (Unlock)’ button on the keychain transmitter.
The siren will "chirp" 2 times and the vehicle's parking lamps will flash two times.
The dash mounted LED will flash until door is opened, and then remain off until the system is re-armed.
AUTOMATIC –PASSIVE LAST DOOR LOCKING –PROGRAMABLE
IF central door locking connected to security system It is the same sequence as above except that the doors will
also lock automatically.
If you wish to arm the system immediately, simple press and release the ARMING button on the remote.
PROTECTION WHILE THE SYSTEM IS ARMED:
Opening any door, bonnet or boot will cause the alarm to sound. The siren will continue to sound for 30
seconds, then stop and automatically re-arm the vehicle.
If a door is left open, the siren will sound for six 30 second cycles, then re-arm and ignore the opened door.
Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle,
whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual
deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle's battery to
drain, even when left unattended for extended periods.
Whenever the system is triggered, the vehicle's parking lights will flash for the 30 second alarm cycle,
attracting added visual attention to the vehicle.
Whenever the system is armed, the vehicle's starter will be immobilised. This prevents the engine from
being started.
INTRUSION WARNING SIGNALS:
The system will inform you if an intrusion attempt has occurred while you were away from the vehicle.
If an intrusion attempt has occurred, the siren will "chirp" 4 times when disarming the system.
The vehicle's parking lights will also flash 3 times to indicate an intrusion has occurred.
Enter the vehicle and observe the dash mounted LED...it will flash a code.
If the LED is flashing one time... pause...one time... etc., then the alarm was triggered via the shock sensor.
If the LED is flashing two times...pause. ..two times...etc., then the alarm was triggered via the bonnet or
boot ....or an optional sensor, such as a glass break sensor, has been connected to one of these circuits.
If the LED is flashing three times...pause...three times...etc., then an intrusion attempt was made through
one of the vehicle's doors.
These intrusion warning indicators are stored in the system's memory and will only be erased from memory
when the ignition key is turned on.
ELIMINATING THE ARM / DISARM CHIRPS:
The normal arming and disarming confirmation "chirps" can easily be turned on and off using the valet push
button switch.
To do this:
Turn the ignition key on, and then off.
Within 10 seconds of turning the ignition key off, press and release the LED valet push button switch three
times.
If the chirps were on, then you will hear 2 chirps to indicate that the chirps have been turned off.
If the chirps were off, then you will hear 1 chirp to indicate that the chirps have been turned on.
NOTE:
Whenever the chirps are by-passed, the defect and intrusion chirps will always operate.
BOOT RELEASE BY REMOTE
If you vehicle is equipped with electric release of the boot, it can be connected to this alarm system. This
may incur additional charges. Press the ‘boot’ button on the remote control to activate.
PANIC
In the event of personal attack, the alarm can be ‘panicked’ by pressing the ‘arm’ button on the remote
control button for 3 seconds.
Press the ‘boot’ button on the remote control to cancel. It auto cancels after 30 seconds.
ELECTRONIC SIREN
This is mounted under the bonnet and must be situated in a place to protect it from heat and water damage
such as driving through deep water or engine cleaning. If washing the engine bay, cover the siren with a
plastic bag to prevent damage. Heat or water damage is not covered by the warranty.
IGNITION SAFETY DOOR LOCK/UNLOCK (Programmable)
If the central locking is connected to this security system, the doors will automatically lock after 1 second when
the engine is started (or ignition is turned on). The doors will unlock when the ignition is turned off.
If a door is left open during engine starting, the doors will not lock.
‘Lock’ and ‘unlock’ can be programmed separately.
REMOTE CONTROL CODE LEARNING
If you need to replace a remote control, it must be memorised to the alarm system before it can be used.
A power surge or interruption to the power supply may cause loss of memory.
If your alarm fails to respond to the remote try re-learning them.
The following action deletes any previous remotes, so all existing remotes must be memorised with this
sequence.
Turn the ignition key to the ON position.
Press and release the valet/programming switch 3 times (Siren Chirps)
Press the Lock Button of each transmitter you want programmed until you hear a chirp from the siren.
Press and release the valet/programming switch 1 time to advance to channel 2 UNLOCK. Press
the unlock button of each transmitter you want to unlock the vehicle.
Press and release the valet/programming switch 1 time to advance to channel 3 BOOT. Press the boot
button of each transmitter you want to operate the boot release of the vehicle.
Turn the ignition switch to the OFF position.
The above action programs the Lock, Unlock and Boot Release functions of the system
HIDDEN PUSH BUTTON LED VALET / OVERRIDE / PROGRAMMING SWITCH:
Make sure your installer of this security system shows you where the hidden switch is located.
The "Valet" switch allows you to temporarily bypass all alarm functions. In valet mode, all alarm functions
are bypassed, however, the remote panic feature and remote door locks (optional) will remain operational.
To use the valet mode, enter the vehicle and turn the ignition key to the ON position.
Press and hold the hidden LED valet push button switch for 5 seconds until the LED turns on solid. The
LED will remain on as long as the system is in the valet mode.
To return to normal operation, with the ignition switch on, press and release the LED valet push button
switch one time. The LED will turn off indicating the unit has been returned to the normal mode of
operation.
In the event you lose your keychain transmitter, or if the transmitter fails to disarm the system, the valet
switch can be used as a system override switch.
Open the car door (the alarm will sound). Turn the ignition key on, and press and hold the LED valet switch
on. The alarm will stop sounding, and the vehicle can now be started.
INDICATOR LIGHT FLASH CONFIRMATION / CODES
This is a visual indication of system status.
A ) 1 Flash - Armed
B ) 2 Flash - Disarmed
C)3 Flash-Indicatessystemhasbeentriggered
SIREN CHIRP CODES
This is an audible indication of system status.
A ) 1 Chirp - Armed
B ) 2 Chirps - Disarmed
C ) 3 Chirps - Open circuit when arming
D ) 4 Chirps - Intrusion upon disarm
DASH MOUNTED WARNING LIGHT - LED
Located on or near the dashboard area, the LED is a small flashing light that indicates the vehicle is fitted
with a security system. The LED also tells the status of the alarm;
A) Slow flashing - System armed
B) Fast flashing - Countdown for automatic passive arming
B) LED off - System is off
C) Solid lit - Valet mode
D) 1 flash - Shock sensor triggered
E) 2 flash - Bonnet or boot triggered (or optional sensor)
F) 3 flash - Door triggered
REMOTE CONTROL CODE LEARNING
If you need to replace a remote control, it must be memorised to the alarm system before it can be used.
A power surge or interruption to the power supply may cause loss of memory.
If your alarm fails to respond to the remote try re-learning them.
The following action deletes any previous remotes, so all existing remotes must be memorised with this
sequence.
Turn the ignition key to the ON position.
Press and release the valet/programming switch 3 times (Siren Chirps)
Press the Lock Button of each transmitter you want programmed until you hear a chirp from the siren.
Press and release the valet/programming switch 1 time to advance to channel 2 UNLOCK. Press the
unlock button of each transmitter you want to unlock the vehicle.
Press and release the valet/programming switch 1 time to advance to channel 3 BOOT. Press the boot
button of each transmitter you want to operate the boot release of the vehicle.
Turn the ignition switch to the OFF position.
The above action programs the Lock, Unlock and Boot Release functions of the system
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Mongoose Autoalarmanlage Handbücher
Mongoose
Mongoose M20 Gebrauchsanweisung
Mongoose
Mongoose MAP77 Bedienungsanleitung
Mongoose
Mongoose MX40 II Series Produkthandbuch
Mongoose
Mongoose M60i Installationshandbuch
Mongoose
Mongoose TT1 Bedienungsanleitung
Mongoose
Mongoose M40 Bedienungsanleitung
Mongoose
Mongoose M33 Gebrauchsanweisung
Mongoose
Mongoose M30 Gebrauchsanweisung
Mongoose
Mongoose EMS 1.7R Bedienungsanleitung
Mongoose
Mongoose M80II Upgrade Bedienungsanleitung
Mongoose
Mongoose M80i Montageanleitung
Mongoose
Mongoose EMS 1.9R Bedienungsanleitung
Mongoose
Mongoose M30 Gebrauchsanweisung
Mongoose
Mongoose M20 Gebrauchsanweisung
Mongoose
Mongoose M60i Gebrauchsanweisung
Mongoose
Mongoose MAP80 Bedienungsanleitung
Mongoose
Mongoose EMS 1.9R Bedienungsanleitung
Mongoose
Mongoose MX40 II Series Produkthandbuch
Mongoose
Mongoose Striker - MCA500 Bedienungsanleitung
Mongoose
Mongoose M25 Bedienungsanleitung
Beliebte Autoalarmanlage Handbücher anderer Marken
Federal Signal Corporation
Federal Signal Corporation Pathfinder Siren Series Handbuch
Falcon
Falcon Predator XL3 Benutzerhandbuch
Audiovox
Audiovox Auto Security XR91 Betriebsanleitung
Clifford
Clifford Sabre II Bedienungsanleitung
CrimeStopper
CrimeStopper CS-8717 Kurzanleitung
Ultra Start
Ultra Start 450 SERIES Bedienungsanleitung
