Monogram ZIC360NHRH Bedienungsanleitung

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

SECTION 1

SECTION 2

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

FLUSH INSET INSTALLATION

STANDARD INSTALLATION

OVERALL DIMENSIONS

AFTER PANEL INSTALL

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An individual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

FLUSH INSET INSTALLATION

SPECIFICATIONS

Overall Width 38" (96.5 cm)†

Overall Height 84 1/2" (214.6 cm)†

Overall Depth 26" (66.0 cm)†

Door Clearance 38 3/4" (98.4 cm)

Cutout Width 39" (99.1 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 640 lb (290.3 kg)

38" (96.5)

11 1/2"

(29.2)

20 5/8" (52.4)

26" (66.0)

* 84 1/2"

(214.6)

*73"

(185.4)

*26 7/16"

(67.1)

*4"

(10.2) *4"

(10.2) SIDE VIEWFRONT VIEW

* 83 1/2"

(212.1)

35" (89.0)

Case width

38 3/4"

(98.4)

TOP VIEW

ZIC360NHRH

Allow 4" (10.2) min

clearance to a wall

for 90˚ door swing

Allow 15" (38.1) min

clearance for 115˚

door swing

* Shipping height. Use leveling legs and wheels for maximum 1" height

adjustment from shipping height. Nominal installation height is 84”

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area.

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

The information below applies to all

installation constructions:

• A wall bracket, bolts and toggles will

be supplied with the unit.

• The bolts will be used to attach bracket

to wall in 4 locations. Two of the

locations must penetrate the center of

the wall studs.

• The toggles are used for stability in

drywall and when metal studs are

encountered. Lag bolts are used in

wood studs.

• In installation opening, measure 82"

from ﬂoor and draw a horizontal line.

• Locate and mark the wall studs on

horizontal line. Verify at least two studs

have their centerlines within the center

32.5" of installation opening to ensure

2 wall studs are penetrated.

• The bracket will be centered left to

right in opening with bottom of bracket

on the horizontal line.

• When unit is placed in opening, the

bracket tabs will align with openings

in back of the unit. The unit will be

secured to the bracket using supplied

“L” bolts.

See Installation Instructions for

detailed instructions.

FLUSH INSTALLATION

ZIC360NHLH_RH

39" (99.1) Flush inset width

37 1/2" (95.3)

Width between cleats

3/4" (1.9)

Width of side cleats

5 1/4" (13.3)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

3 1/2"

(8.9)

Finished cleats

Case Trim

3/4" Panel

Case

Door

(15.2)

24 3/16"

(61.4)

(17.8)

10"

(25.4)

3 1/2"

(8.9)

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

84"

(213.4)

height

to cleat

85"

(215.9)

WATER

3 1/2"

(9.0)

NOTES

FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION

ANTI-TIP BRACKET

24" (61.0)

1 1/2"

(3.8)

(7.6)

7/16"

(1.1)

Trim overlap

35 1/2" (90.2)

2 5/16"

(5.9)

SIDE VIEWFRONT VIEW

ZIC360NXRH

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

ELEC. 6"

(15.2)

10"

(25.4)

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

WATER

(12.7)

3 1/2"

(9.0)

WATER

10" (25.4)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

centered

within the

cutout

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

NOTES

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed 1/2" or 3/4" custom door, drawer

and grille panels are required. For 3/4"

raised panels, routing is required. The router

depth is 1/4" all the way around the panel’s

backs. Additional panel width reductions

are required per the diagrams shown. This

will create “picture frame’ routing allowing

the panels to slide into the attached door,

drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

Note: For panels constructed with rails and

stiles (5-panel), the rails must be a minimum

of 3" wide and stiles must be a minimum of

4" wide.

Door Handles

Door handles not included. Custom handles

supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel

handle designed to ﬁt custom panels. Kit

includes one handle – 30 1/2" long. Order

2 kits from your Monogram supplier.

ZKHCSS2: Custom European tubular handle

designed to ﬁt custom panels. Kit includes 2

handles. Door handle is 44 3/16" and drawer

handle is 33 3/16".

Order ZUG2: Uniﬁed grille kit for

dual installation. Maximum total panel

weight - 25 lbs.

ZKHCT: Handle side trim for left-hand and

right-hand door. For use on a custom panel

when using a custom handle.

FLUSH INSET INSTALLATION

Grille Panel

Fresh

Food

Panel

Freezer Drawer Panel

A B C D

38" 10 11/16" 46 9/16" 22 7/16"

PANEL DIMENSIONS

FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION

3/4" RAISED DOOR PANEL ROUTING

3/4"

11/32"

1/4"

3/16"

1/4" 7/16"

DETAIL TOP

DETAIL BOTTOM

DETAIL

LEFT SIDE

DETAIL RIGHT

SIDE

2-1/16" 2-1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

1/4"

3/32"

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

NOTES

FLUSH INSET INSTALLATION

3/4" RAISED GRILL PANEL ROUTING

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

DETAIL TOP

DETAIL BOTTOM

3/16"

1-11/16"

ROUTER DEPTH 1/4"

DETAIL

LEFT SIDE

DETAIL RIGHT

SIDE

2-1/16" 2-1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

1/4"

3/32"

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed 1/2" or 3/4" custom door, drawer

and grille panels are required. For 3/4"

raised panels, routing is required. The router

depth is 1/4" all the way around the panel’s

backs. Additional panel width reductions

are required per the diagrams shown. This

will create “picture frame’ routing allowing

the panels to slide into the attached door,

drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

Note: For panels constructed with rails and

stiles (5-panel), the rails must be a minimum

of 3" wide and stiles must be a minimum of

4" wide.

Door Handles

Door handles not included. Custom handles

supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel

handle designed to ﬁt custom panels. Kit

includes one handle – 30 1/2" long. Order

2 kits from your Monogram supplier.

ZKHCSS2: Custom European tubular handle

designed to ﬁt custom panels. Kit includes 2

handles. Door handle is 44 3/16" and drawer

handle is 33 3/16".

Order ZUG2: Uniﬁed grille kit for

dual installation. Maximum total panel

weight - 25 lbs.

ZKHCT: Handle side trim for left-hand and

right-hand door. For use on a custom panel

when using a custom handle.

3/4" RAISED DRAWER PANEL ROUTING

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

3/4"

11/32"

1/4"

3/16"

1/4" 7/16"

DETAIL TOP

DETAIL BOTTOM

2 1/16" 2 1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

DETAIL

LEFT SIDE

DETAIL RIGHT

SIDE

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area.

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

The information below applies to all

installation constructions:

• A wall bracket, bolts and toggles will

be supplied with the unit.

• The bolts will be used to attach bracket

to wall in 4 locations. Two of the

locations must penetrate the center of

the wall studs.

• The toggles are used for stability in

drywall and when metal studs are

encountered. Lag bolts are used in

wood studs.

• In installation opening, measure 82"

from ﬂoor and draw a horizontal line.

• Locate and mark the wall studs on

horizontal line. Verify at least two studs

have their centerlines within the center

32.5" of installation opening to ensure

2 wall studs are penetrated.

• The bracket will be centered left to

right in opening with bottom of bracket

on the horizontal line.

• When unit is placed in opening, the

bracket tabs will align with openings

in back of the unit. The unit will be

secured to the bracket using supplied

“L” bolts.

See Installation Instructions for

detailed instructions.

FLUSH INSTALLATION

ZIC360NHLH_RH

39" (99.1) Flush inset width

37 1/2" (95.3)

Width between cleats

3/4" (1.9)

Width of side cleats

5 3/8" (13.7)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 13/16" (52.9)

Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

3 1/2"

(8.9)

Finished cleats

Case Trim

1/2" Panel

Case

Door

(15.2)

24 3/16"

(61.4)

(17.8)

10"

(25.4)

3 1/2"

(8.9)

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

84"

(213.4)

height

to cleat

85"

(215.9)

WATER

3 1/2"

(9.0)

NOTES

FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET INSTALLATION

ANTI-TIP BRACKET

24" (61.0)

1 1/2"

(3.8)

(7.6)

7/16"

(1.1)

Trim overlap

35 1/2" (90.2)

2 5/16"

(5.9)

SIDE VIEWFRONT VIEW

ZIC360NXRH

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

ELEC. 6"

(15.2)

10"

(25.4)

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

WATER

(12.7)

3 1/2"

(9.0)

WATER

10" (25.4)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

centered

within the

cutout

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

NOTES

The 1/2" overlay panel must be secured

to a .10" spacer panel and a 1/4" thick

backer panel, which slides into the trim.

Assemble the panels with glue and

screws:

• Center the spacer panel on the backer

panel, left to right and top to bottom.

Secure the panels with glue.

• Refer to the chart for locating the backer

panel to the overlay panel. Secure

the overlay panel to the backer panel

with glue and screws. Screws must be

countersunk into the backer panel

Order ZUG2: Uniﬁed grille kit for dual

installation. Maximum total panel

weight – 25 lbs.

Note: For panels constructed with rails

and stiles (5-panel), the rails must be a

minimum of 3" wide and stiles must be a

minimum of 4" wide.

FLUSH INSET INSTALLATION

FLUSH INSET 1/2" PANEL DIMENSIONS

1/2" OVERLAY PANEL ROUTING DIMENSIONS

A B C D

1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"

.10" Space Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"

1/2" Overlay Panel 38" 10 11/16" 46 9/16" 22 7/16"

A B C D

Fresh Food Panel 2 1/16" 2 1/16" 5/16" 3/16"

Freezer Panel 2 1/16" 2 1/16" 5/16" 3/16"

Grille Panel 2 1/16" 2 1/16" 1 11/16" 3/16"

Grille Panel

Fresh

Food

Panel

Freezer Drawer Panel

PANEL DIMENSIONS

A B

Grille Back

Hinge Side

Backer with

Overlay Panel

Assembly

Door Panel Back

Freezer Drawer

1/2"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

PANEL DIMENSIONS

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

NOTES

FLUSH INSET INSTALLATION

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed 1/2" or 3/4" custom door, drawer

and grille panels are required. For 3/4"

raised panels, routing is required. The router

depth is 1/4" all the way around the panel’s

backs. Additional panel width reductions

are required per the diagrams shown. This

will create “picture frame’ routing allowing

the panels to slide into the attached door,

drawer and grille trims.

AA separate 115V, 60Hz, 15- or 20-amp

power supply is recommended for each

product.

Maximum total panel weight:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Unied grille panel – 25 lbs

Door Handles

Door handles not included. Custom handles

supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel

handle designed to ﬁt custom panels. Kit

includes one handle – 30 1/2" long. Order

2 kits from your Monogram supplier.

ZKHCSS2: Custom European tubular handle

designed to ﬁt custom panels. Kit includes 2

handles. Door handle is 44 3/16" and drawer

handle is 33 3/16".

Order ZUG2: Uniﬁed grille kit for

dual installation. Maximum total panel

weight - 25 lbs.

ZKHCT: Handle side trim for left-hand and

right-hand door. For use on a custom panel

when using a custom handle.

The 1/2" overlay panel must be secured to

a .10" spacer panel and a 1/4" thick backer

panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer

panel, left to right and top to bottom. Secure

the panels with glue.

• Refer to the chart for locating the backer

panel to the overlay panel. Secure the

overlay panel to the backer panel with glue

and screws. Screws must be countersunk

into the backer panel

FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION

PANEL DIMENSIONS

Grille Panel

Fresh

Food

Panel

Freezer Drawer Panel

Fresh

Food

Panel

Freezer Drawer Panel

A B C D E

1/4" Backer Panel 69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"

.10" Space Panel 68 1/2" 7 5/8" 44 11/16" 20 1/2" 32 1/2"

1/2" Overlay Panel 74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"

3/4" or 1/2" DUAL INSTALLATIONS

ZIC360NHLH_ZIC360NHRH

75" (190.5)

Finished Width

26 3/16" (66.5)

Min. Cutout Depth

24 3/16" (61.4)

4 5/16"

(10.9)

5 1/2"

(13.9)

(22.9)

85"

(215.9)

Finished

Opening

3 1/2"

(8.9)

FRONT VIEW

ELEC. 5 1/2"

(13.9)

(22.9)

3 1/2"

(8.9)

15" (38.1) min

To wall 15" (38.1) min

To wall

(2.5)

115˚

Door swing 115˚

Door swing

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

SIDE VIEW

(17.8) 7"

(17.8)

WATER

3 1/2"

(9.0)

WATER

3 1/2"

(9.0)

7 1/2"

(19.1) 7 1/2"

(19.1)

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

NOTES

FLUSH INSET INSTALLATION

Grille Panel

Fresh

Food

Panel

Freezer Drawer Panel

Fresh

Food

Panel

Freezer Drawer Panel

A B C D E

74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"

PANEL DIMENSIONS

FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed 1/2" or 3/4" custom door, drawer

and grille panels are required. For 3/4"

raised panels, routing is required. The router

depth is 1/4" all the way around the panel’s

backs. Additional panel width reductions

are required per the diagrams shown. This

will create “picture frame’ routing allowing

the panels to slide into the attached door,

drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 58 lbs.

• Freezer drawer panel – 28 lbs.

• Unied grille panel – 25 lbs

Door Handles

Door handles not included. Custom handles

supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel

handle designed to ﬁt custom panels. Kit

includes one handle – 30 1/2" long. Order

2 kits from your Monogram supplier.

ZKHCSS2: Custom European tubular handle

designed to ﬁt custom panels. Kit includes 2

handles. Door handle is 44 3/16" and drawer

handle is 33 3/16".

Order ZUG2: Uniﬁed grille kit for

dual installation. Maximum total panel

weight - 25 lbs.

ZKHCT: Handle side trim for left-hand and

right-hand door. For use on a custom panel

when using a custom handle.

3/4" RAISED DOOR AND DRAWER PANEL ROUTING - (SEE PAGE 5

FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

HINGE

SIDE

HANDLE

SIDE

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

3/4"

11/32"

1/4"

3/16"

1/4" 7/16"

DETAIL TOP

DETAIL BOTTOM

2 1/16" 3/16"

ROUTER DEPTH 1/4"

DETAIL HINGE

SIDE

DETAIL HANDLE

SIDE

ZIC360NHRHMonogram®36" Built-In Bottom-freezer Refrigerator

Product Speciﬁcation Revised 5/16

NOTES

FLUSH INSET INSTALLATION

AIn a side-by-side installation of a left-

and-right-hand door swing product, 1"

clearance between the units is required.

Order ZUG2 custom panel uniﬁed grille

kit for this installation.

3/4" or 1/2" DUAL PRODUCT CLEARANCES

ZIC360NHLH_ZIC360NHRH

75" (190.5)

Finished Width

26 3/16" (66.5)

Min. Cutout Depth

24 3/16" (61.4)

4 5/16"

(10.9)

5 1/2"

(13.9)

(22.9)

85"

(215.9)

Finished

Opening

3 1/2"

(8.9)

FRONT VIEW

ELEC. 5 1/2"

(13.9)

(22.9)

3 1/2"

(8.9)

15" (38.1) min

To wall 15" (38.1) min

To wall

(2.5)

115˚

Door swing 115˚

Door swing

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

SIDE VIEW

(17.8) 7"

(17.8)

WATER

3 1/2"

(9.0)

WATER

3 1/2"

(9.0)

7 1/2"

(19.1) 7 1/2"

(19.1)

Inhaltsverzeichnis

Andere Monogram Kühlschrank Handbücher

Monogram

Monogram ZIBS240 Bedienungsanleitung

Monogram

Monogram ZPB480D Bedienungsanleitung

Monogram

Monogram ZWE23E series Bedienungsanleitung

Monogram

Monogram Monogram ZISB360DR Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram GE RPWFE Bedienungsanleitung

Monogram

Monogram ZIS480NRF Bedienungsanleitung

Monogram

Monogram ZIFI240HII Bedienungsanleitung

Monogram

Monogram ZIFX240HX Bedienungsanleitung

Monogram

Monogram ZIS360N Bedienungsanleitung

Monogram

Monogram ZIF181 Bedienungsanleitung

Monogram

Monogram 224D3094P002 Bedienungsanleitung

Monogram

Monogram ZFGB21HXCSS Bedienungsanleitung

Monogram

Monogram Monogram ZISB360DR Benutzerhandbuch

Monogram

Monogram Monogram ZISW36DRC Bedienungsanleitung

Monogram

Monogram ZICP720 Bedienungsanleitung

Monogram

Monogram ZICS360NXLH Kurzanleitung

Monogram

Monogram ZISP480DHSS Bedienungsanleitung

Monogram

Monogram Monogram ZFSB26DRSS Benutzerhandbuch

Monogram

Monogram ZIR300NPKII Bedienungsanleitung

Monogram

Monogram ZDOD240HSS Bedienungsanleitung

Monogram

Monogram ZISB42E Bedienungsanleitung

Monogram

Monogram ZFGP21HXASS Bedienungsanleitung

Monogram

Monogram ZIP360NH Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung