Monogram ZISP480DHSS Bedienungsanleitung

Side by Side Refrigerators

Design Guide

With Installation Instructions

Installation

Instructions

04-15 GE

monogram.com

31-49077-2

224D1889P016

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT– Save these instructions for

local inspector’s use. Observe all governing codes

and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged refrigerator, you should

immediately contact your dealer or builder.

Skill Level – Installation of this refrigerator requires

basic mechanical, carpentry and plumbing skills.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the GE Appliance Warranty.

See the Owner’s Manual for warranty information.

WARNING Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately replace electric cords that become frayed

or damaged.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the

Refrigerator.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These

words are defined as:

DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

For Monogram local service in your area, call 1.800.444.1845.

For Monogram service in Canada, call 1.800.561.3344

For Monogram Parts and Accessories, call 1.800.626.2002.

www.monogram.com

WARNING Tip Over Hazard.

These refrigerators are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the refrigerator with the anti-tip system.

WARNING Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in

fire, explosion, or death.

WARNING To reduce the risk associated with choking, do not allow children under 3 years of age to have

access to small parts during the installation of this product.

CAUTION Lifting Hazard

This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this

refrigerator, 3 people are required for proper installation of 36” wide model and 4 people are required for proper

installation of a 42” or 48” wide model.

AVERTISSEMENT Risque de basculement

Ces réfrigérateurs présentent une partie supérieure lourde, en particulier avec une porte ouverte; ils doivent donc

être fixés pour prévenir le basculement vers l’avant et le risque concomitant de blessure grave ou fatale. Lisez et

suivez les instructions d’installation complètes pour l’installation du système anti-basculement.

AVERTISSEMENT Risque d’explosion.

Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le non-

respect de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès.

AVERTISSEMENT Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les

petites pièces à la portée des enfants âgés de moins de 3 ans.

ATTENTION Risque associé à la manutention d’une charge lourde

Ce réfrigérateur est très lourd. Pour réduire le risque de blessure lors de la manutention de ce réfrigérateur, trois

(3) personnes sont nécessaires pour procéder à l’installation appropriée du modèle 36 pouces, quatre (4) pour

l’installation des modèles 42 ou 48 pouces.

Consignes de Sécurité

AVERTISSEMENT Risque de choc électrique.

Branchez l’appareil dans une prise triple avec terre.

Ne retirez pas la broche de terre.

N’utilisez pas d’adaptateur.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Remplacer immédiatement tout cordon électrique

effiloché ou endommagé.

N’utilisez pas de rallonge avec cet appareil.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Suivez les instructions de la section Mise à la terre du

réfrigérateur.

Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des

blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots «

DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants :

Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des bles

sures graves, voire la mort.

Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des

blessures graves, voire la mort. .

Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des

blessures mineures ou graves.

AVERTISSEMENT

DANGER

ATTENTION

Contents

Safety 2, 3

Instructions for Standard Installation 5-22

Planning Guide

The Installation Space 6

Dimensions and Clearances 6

Customization Basics 7

Side Panels 7

Refrigerator Location 7

1/4” Framed Panel Dimensions 8

3/4” Overlay Panel Dimensions 9

130° Door Swing 10

90° Door Swing 11

Dispenser Trim 12

Installation Instructions

Tools, Hardware, Materials 13

Grounding the Unit 13

Step 1. Remove Packaging 14

Step 2. Move the Refrigerator into the House 14

Step 3. Install Water Line 14

Step 4. Installation with Filtration System 15

Step 5. Install Side Panels 15

Step 6. Anti-Tip Procedures 15

Step 7. Level Refrigerator 16

Step 8. Alternate Anti-Tip Procedure 16

Step 9. Adjust Door Swing 17

Step 10. Install Grille Panel 17

Step 11. Install 1/4” Framed Panels 18

Step 11A. Install Overlay Panels 19, 20

Step 12. Connect Water Supply 20, 21

Step 13. Connect Power, Close Grille Panel 21

Step 14. Start Icemaker 21

Step 15. Install Toekick 21

Inspect Final Installation 22

Instructions for Flush Installation 23-40

Planning Guide

The Installation Space 24

Dimensions and Clearances 24

Customization Basics 25

Custom Handle Design Guide 25

Refrigerator Location 25

Side Panels 25

1/2” Overlay Panel Dimensions 26

3/4” Raised Panel Dimensions 27

3/4” Raised Door Panel Routing 28

3/4” Raised Grille Panel Routing 29

Dispenser Trim 30

Side Cleats 30

Installation Instructions

Tools, Hardware, Materials 31

Grounding the Unit 29

Step 1. Remove Packaging 32

Step 2. Move the Refrigerator into the House 32

Step 3. Install Water Line 32

Step 4. Installation with Water Filtration System 33

Step 5. Install Side Panels 33

Step 6. Install Case Trim 33

Step 7. Anti-Tip Procedure 33-34

Step 8. Level Refrigerator 34

Step 9. Adjust Door Swing 35

Step 10. Install Grille Panel 36

Step 11. Install 1/4” Framed Panels 37

Step 11A. Install Overlay Panels 38

Step 12. Connect Water Supply 39

Step 13. Connect Power, Close Grille Panel 39

Step 14. Start Icemaker 39

Step 15. Install Toekick 40

Inspect Final Installation 40

Instructions for Stainless Steel Installation 41-49

Planning Guide

The Installation Space 42

Dimensions and Clearances 42

Customization Basics 43

Side Panels 43

Refrigerator Location 43

130° Door Swing 44

90° Door Swing 45

Installation Instructions

Tools, Hardware, Materials 46

Grounding the Unit 46

Step 1. Remove Packaging 47

Step 2. Moving the Refrigerator into the House 47

Step 3. Install Water Line 47

Step 4. Installation with Water Filtration System 48

Step 5. Install Side Panels 48

Step 6. Anti-Tip Procedure 48

Step 7. Level Refrigerator 49

Step 8, Alternate Anti-Tip Procedure 49

Step 9. Adjust Door Swing 49

Step 10. Connect Water Supply 50

Step 11. Connect Power, Close Grille Panel 50

Step 12. Start Icemaker 50

Step 13. Install Toekick 51

Inspect Final Installation 51

Instructions for Standard Installation

Design Guide - Standard Installation

THE INSTALLATION SPACE

Water And Electrical Locations

The opening must be prepared with the electrical and

the cold water supply located as shown.

The Cutout Depth Must Be 24”

The refrigerator will project forward, slightly beyond

adjacent cabinetry for standard installation.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be located

on the rear wall as shown.

NOTE: GFI (ground fault interrupter) is not recommended.

• The water line can enter the opening through the floor

or back wall. The water line should be 1/4” O.D. copper

tubing or GE SmartConnect™kit between the cold

water line and water connection location, long enough

to extend to the front of the refrigerator. Installation of

an easily accessible shut-off valve in the water line is

required.

DIMENSIONS AND CLEARANCES

* Shipping height.

The refrigerator can

be adjusted to fit

into a cutout that

is 84-1/2” in height.

Use leveling legs

and wheels for a

maximum 1” height

adjustment.

Product Clearances

These refrigerators are

equipped with a 3-position

door stop. The factory-set

115° door swing can be

adjusted to 130°, or to 90°

if clearance to adjacent

cabinets or walls is

restricted.

90° Door Swing

130° Door Swing

115° Door Swing

*Finished Width

Electrical

Area

85" max

Finished

Opening 75" From Floor

to Bottom

of Electrical

Area

24"

5" 5" 3 1/2"

Water Supply

3 1/2"

36" Models 12"

42" Models 18"

48" Models 20"

Allow minimum clearances for the freezer door

(Dimension A) and fresh food door (Dimension B) for a full

130° door swing and to allow for pan removal.

For a 90° door swing, allow 4” min. clearance to a wall.

If the 90° door stop position is used, pan access is

maintained, but pan removal is restricted.

See the illustrations on pages 10 and 11 to determine

door swing interaction with adjacent cabinets or

countertops.

Models A B C

36” 13” 15” 20-5/8”

42” 13” 19” 26-5/8”

48” 15” 20” 28-5/8”

*84"

From

Floor

25-3/8" Framed Models

Depth Including Handles 26-7/8”

36", 42" or 48"

Frame to Frame

35", 41", or 47"

Case Width

*83-1/2"

Rear

23-7/8"

Behind

Frame

*Min. Distance

to Wall

4”

*The finished cutout width must be:

35-1/2” for 36” models

41-1/2” for 42” models

47-1/2” for 48” models

CUSTOMIZATION BASICS:

These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels

are required.

Optional Accessory Kits

ZKHSS2: Monogram Tubular Stainless Steel handles

designed to fit 3/4” overlay panels. ZKHPSS1: Professional Tubular Stainless Steel handles

designed to fit 3/4” overlay panels. Kit includes one handle.

Order 2 kits for side-by-side refrigerator models from your

Monogram supplier

Design Guide - Standard Installation

SIDE PANELS

Side panels must be used

whenever the sides of the

refrigerator will be exposed.

The 1/4” side panels will

slip into the side case trim.

Secure the panels to the

refrigerator with stick-on

hook and loop fastener

strips. Order the side

panels from the cabinet

manufacturer.

• Cut a notch in the top

front corner as shown

to allow clearance for

corner keys in the front

side trim. * Depending on installation height.

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 55°F (13°C). It will not run often enough

to maintain proper temperatures.

• Do not install the refrigerator where temperatures will

go above 100°F (37°C). It will not perform properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded.

1/4” FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must

be cut to the dimensions shown. The panels will slide

into the frame on the door and grille.

Non-Dispenser Models

If the custom panel is less than 1/4” thick and it fits

loosely in the door frame it can be backed up with

a piece of filler material or foam tape to improve

the fit.

Fresh

Food

Panel

Freezer

Panel

Grille Panel

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8

Side-by-Side (in inches)

A B C D E F G

36” Models 33-7/8 9 68-3/8 14-9/16 18-9/16 17-13/16 3-1/8

42” Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16 17-13/16 3-1/8

48” Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16 17-13/16 5-1/8

Dispenser

Cutout Position

IMPORTANT NOTE: Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer door panel – 53 lbs.

• Grille Panel – 18 lbs.

1/4"

Panel

Door

5/16"

Trim

Reveal

The framed panel must be 1/4” nominal

thickness to fit the dispenser trim.

IMPORTANT NOTE – DISPENSER MODELS

The refrigerator is supplied with two dispenser trims,

one for framed panels and one for overlay panels.

• If the panel is less than 0.250” thick, a noticeable gap

may be created around the dispenser trim. Foam

tape may be applied on the door to improve the fit.

• If the panel is more than 0.250” thick, the dispenser

trim cannot be secured to the door.

See Dispenser Trim Fit Example, page 12.

Design Guide - Standard Installation

3/4” OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may

be installed on trimmed models. The overlay panel must

be secured to a 1/4” thick backer panel which slides

into the trim. A spacer panel 0.10” thick must be placed

between the overlay and backer panel.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay

panel and secure with glue and screws. Screws must

be countersunk into the backer panel.

NOTE: Left-to-right offset is

not always equal to top-to-

bottom offset.

Spacer Panel

OverlayPanel

Backer Panel

Fresh

Food

Panel

Freezer

Panel

Grille Panel

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8

*Cut the dispenser opening after the backer, spacer and overlay

panels have been assembled.

36” Side-by-Side (in inches)

A B C D E F G

1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16

.10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4

3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 17-15/16 3-1/4

42” Side-by-Side (in inches)

A B C D E F G

1/4” Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16

.10” Spacer Panel 39 8-5/8 67 13-1/4 23-1/4

3/4” Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16 17-15/16 3-1/4

48” Side-by-Side (in inches)

A B C D E F G

1/4” Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16

.10” Spacer Panel 45 8-5/8 67 17-1/4 25-1/4

3/4” Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16 17-15/16 5-1/4

*Dispenser

Cutout Position

IMPORTANT NOTE: Maximum total weight for the assembled

panels:

• Fresh food door panel – 75 lbs.

• Freezer door panel – 53 lbs.

• Grille Panel – 18 lbs.

IMPORTANT NOTE – DISPENSER MODELS

The refrigerator is supplied with two dispenser trims,

one for framed panels and one for overlay panels. The

overlay dispenser trim is designed to fit a total panel

thickness of 1.100”.

• If the panel is less than 1.100” a noticeable gap may

be created around the dispenser trim.

• If the panel is more than 1.100” the dispenser trim

cannot be secured to the door.

See Dispenser Trim Fit Example, page 12.

.250” + .10” + .750” = 1.100” Total Panel Thickness

• The overlay panel must be constructed according to

the specifications shown to achieve the correct total

thickness.

• Alternative panel construction methods such as

securing a 3/4” panel to a 1/4” backer panel cannot

be used. Another method, routing a 3/4” thick panel

on all sides, cannot be used. These methods will not

result in the required 1.100” panel thickness.

3/4"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

Design Guide - Standard Installation

1/4" 1/2" 3/4" 1" 1-1/4"

3/4" Overlay

Panel

(Nominal Size)

Stainless Steel

1/4"

1/2"

3/4"

1-1/4"

1-1/2"

1-3/4"

2-1/4"

2-1/2"

2-3/4"

1/4"

1/2"

3/4"

Door

23-7/8" From

Rear of

Refrigerator

Case

Trim

Top View

130° DOOR SWING

Scale 1:1

IMPORTANT NOTE –

FOR DISPENSER MODELS:

Dispenser models are supplied with two

dispenser trims, one to fit framed panels

and one for overlay panels. Dispenser trim

fit to the custom panel depends on correct

panel thickness. Framed panels must be

1/4” nominal. Overlay panels should be

constructed as shown to accomplish a total

1.100” thickness. See pages 19 and 20 for

details.

Frameless Cabinets: The case trim overlaps

cabinets at the top and sides. Therefore,

frameless cabinets may require filler strips

to prevent interfeence with cabinet door

swing. The opening must allow for filler strips.

Inhaltsverzeichnis

Andere Monogram Kühlschrank Handbücher

Monogram

Monogram ZISS360DKSS Bedienungsanleitung

Monogram

Monogram ZFGP21HXASS Bedienungsanleitung

Monogram

Monogram ZIC30GNZII Bedienungsanleitung

Monogram

Monogram ZIP360NH Bedienungsanleitung

Monogram

Monogram ZIF181 Bedienungsanleitung

Monogram

Monogram ZIDS240HSS Bedienungsanleitung

Monogram

Monogram BIS42A Bedienungsanleitung

Monogram

Monogram ZIF360NHXH Bedienungsanleitung

Monogram

Monogram ZIBI240 Bedienungsanleitung

Monogram

Monogram ZIS360N Bedienungsanleitung

Monogram

Monogram ZFSB25D SS Bedienungsanleitung

Monogram

Monogram ZFSB25DXSS Bedienungsanleitung

Monogram

Monogram WX08X10002 Bedienungsanleitung

Monogram

Monogram ZIRS36N LH Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram ZIS36N Bedienungsanleitung

Monogram

Monogram ZISW480D Bedienungsanleitung

Monogram

Monogram Bottom-Freezer Built-In Bedienungsanleitung

Monogram

Monogram Monogram ZIC36N RH Bedienungsanleitung

Monogram

Monogram ZICP720 Bedienungsanleitung

Monogram

Monogram ZISS480DXASS Bedienungsanleitung

Monogram

Monogram BISB42EL Bedienungsanleitung

Monogram

Monogram ZIFI240HII Bedienungsanleitung

Monogram

Monogram 36 Ceramic Cooktop Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung