Monogram ZIDI240 Bedienungsanleitung

Double-Drawer Built-In

Refrigerator

ZIDI240

ZIDS240

Design Guide

With Installation Instructions

If you have questions,call 800.626.2000 or visit our website at: www.monogram.com

Installation

Instructions

Safety Information

BEFORE YOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT –Save these instructions

for local inspector’s use.

IMPORTANT –Observe all governing

codes and ordinances.

Note to Installer – Be sure to leave these

instructions with the Consumer.

Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

WARNING –This appliance must be

properly grounded. See the section below.

AVERTISSEMENT –

Cet appareil doit être correctement mis à la terre.

Consulter la section au-dessous.

If you received a damaged Double-Drawer

Refrigerator, you should immediately contact your

dealer or builder.

Skill Level – Installation requires basic mechanical

skills. Proper installation is the responsibility of the

installer. Product failure due to improper installation

is not covered under the GE Appliance Warranty.

WARNING:

• Double-Drawer Refrigerators are designed to be

built-in only. They cannot be used free-standing.

• Use this appliance only for its intended purpose.

• Immediately repair or replace electrical service

cords that become frayed or damaged.

• Unplug the unit before cleaning or making repairs.

• Repairs should be made by a qualified service

technician.

AVERTISSEMENT :

• Les réfrigérateurs à deux tiroirs sont conçus pour

être encastrés uniquement. Ils ne peuvent pas être

séparés.

• Il ne faut utiliser cet appareil que pour l’usage

pour lequel il a été construit.

• Il faut réparer ou remplacer immédiatement tout

cordon d’alimentation électrique effiloché ou

endommagé.

• Débrancher le bar ou le réfrigérateur a vin avant

le nettoyage ou toute intervention.

• Les réparations doivent être faites par un technicien

qualifié.

For Monogram local service in your area, call

1.800.444.1845

For Monogram service in Canada, call

1.888.880.3030

For Monogram Parts and Accessories, call

1.800.626.2002.

www. monogram.com

GROUNDING THE DOUBLE-DRAWER

REFRIGERATOR

IMPORTANT – Please read carefully.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST

BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with

a three-prong (grounding) plug which mates with a

standard three-prong (grounding) wall receptacle to

minimize the possibility of electric shock hazard from

this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT

OR REMOVE THE THIRD

(GROUND) PRONG

FROM THE POWER CORD.

DO NOT USE AN ADAPTER

PLUG TO CONNECT THE

REFRIGERATOR TO A

2-PRONG OUTLET.

DO NOT USE AN EXTENSION

CORD WITH THIS APPLIANCE.

CONTENTS

Important Information

Tools, Hardware ......................................3

Parts Required ..........................................3

Caring for Your Stainless Steel ..............3

Design Guide (for ZIDS240)

The Installation Space ............................4

Product Clearances ................................4

Side-by-Side Installations ......................4

Design Guide (for ZIDI240)

The Installation Space ............................5

Product Clearances ................................5

Side-by-Side Installations ......................5

Installation Instructions

Step 1, Remove Packaging ....................6

Step 2, Install Custom 3/4″

Drawer Panels and Handles

(ZIDI240 model only) ............................6, 7

Step 3, Level ..............................................7

Step 4, Connect Power............................8

Step 5, Slide Product into Cutout ..........8

Step 6, Set Temperature Controls..........8

Important Information

ZIDI240 MODEL ONLY

PARTS REQUIRED

• Custom handles

• Overlay panels

• Spacer panels

• Backer panels

• Screws

PARTS SUPPLIED

• Drawer side trims

• Optional black or

stainless steel toekick

TOOLS REQUIRED

• Adjustable wrench

• Carpenter’s glue (ZIDI240 model only)

• Screwdriver (ZIDI240 model only)

CARING FOR YOUR STAINLESS

STEEL

• Before installation or first use, we strongly advise

you polish the stainless steel exterior and handles

with a commercially available stainless steel cleaner

such as Stainless Steel Magic™. To preserve and

protect the fine finish we also strongly advise that

you apply stainless steel cleaner monthly.

Design Guide

THE INSTALLATION SPACE

IMPORTANT: Double-Drawer Refrigerators are

designed to be built-in only. They cannot be used

free-standing.

The cutout depth should be 24″

NOTE: The unit is designed to be flush with the

surrounding cabinets.

Additional Specifications

• A 120 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install a

properly grounded 3-prong electrical receptacle

recessed into the back wall as shown. Electrical must be

located on rear wall as shown. NOTE: GFCI (ground

fault circuit interrupter) is not recommended.

PRODUCT CLEARANCES

When installed

in a corner:

Allow 2-1⁄2″min. clearance between Double-Drawer

and adjacent cabinet, wall or other appliances.

Allow 22″min. clearance from the front for drawer

opening.

NOTE: Clearances are based on the noted 2-1⁄8″

handle standoff depth.

• Test the drawer openings. Carefully open and close

the drawers. The drawers should not rub or catch

on adjacent cabinetry. Notify the installer if the

drawers make contact with cabinetry.

Choose the location:

• These products may be closed in on the top and

three sides as long as the front is unobstructed for

air circulation and proper access to the drawers.

• Do not install these products where the temperature

will go below 55°F (13°C) or above 90°F (32°C).

• These products are not designed to be stacked one

over the other.

SIDE-BY-SIDE INSTALLATIONS –

Stainless Steel Models Only

For a complete refreshment center, install a Double-Drawer

Refrigerator beside a Beverage Center, Wine Chiller/

Wine Reserve, Fresh-Food Refrigerator or Bar Refrigerator

with Icemaker.

• A side-by-side installation requires at least a 47-1/2″wide

opening. No trim kits required.

• Products must operate from separate, properly grounded

receptacles.

34-1/2"-35"

24"

47-1/2" Min.

1-1/2"

10-1/2"

10-1/2" 14"

15"

Locate

Outlet

23-3/4"

34-1/2"

23-3/4"

25-7/8"

Including

Handles

Locate

Outlet

34-1/2"-35"

24"

23-3/4" Min.

1-1/2"

Max.

8-1/2"

9" Max.

10-1/2"

1-1/2"

NOTE:

Handle and

handle standoff

depth is 2-1/8″

FOR MODEL ZIDS240 WITH STAINLESS STEEL DRAWERS AND HANDLES

Clearance for Door

Opening 2-1/2" min.

Countertop

Double-Drawer

22" min.

Design Guide

THE INSTALLATION SPACE

IMPORTANT: Double-Drawer Refrigerators are

designed to be built-in only. They cannot be used

free-standing.

The cutout depth should be 24″

The cutout dimensions shown allow for full drawer

extension.

NOTE: The drawers should be flush with the

surrounding cabinets.

Additional Specifications

• A 120 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall as shown. Electrical must be

located on rear wall as shown. NOTE: GFCI (ground

fault circuit interrupter) is not recommended.

PRODUCT CLEARANCES

When installed

in a corner:

Allow 2-1⁄2″min. clearance between Double-Drawer and

adjacent cabinet, wall or other appliances. Allow 23-1⁄8″

min. clearance from the front for drawer opening.

NOTE: Custom handle clearances may vary depending

on the standoff of the custom handles.

• Test the drawer openings. Carefully open and close

the drawers. The drawers should not rub or catch on

adjacent cabinetry. Notify the installer if the drawers

make contact with cabinetry. NOTE: When installing

custom panels and handles, use above clearances as a

general guide but adjust according to the installation.

Choose the location:

• These products may be closed in on the top and

three sides as long as the front is unobstructed for

air circulation and proper access to the drawers.

• Do not install these products where the temperature

will go below 55°F (13°C) or above 90°F (32°C).

• These products are not designed to be stacked one

over the other.

Black or Stainless Steel Toekick Options

• These products are shipped with two toekicks,

a stainless steel and a black toekick. For shipping

purposes, one of the toekicks will be secured to the

back of the unit and the second will be installed,

in place, on the unit. Keep the unused toekick,

and other unused or removed parts, for future use.

23-3/4"

24-7/8"

34-1/2"

Locate

Outlet

34-1/2"-35"

24"

23-3/4" Min.

1-1/2"

Max.

8-1/2"

9" Max.

10-1/2"

1-1/2"

NOTE: Handles

not supplied.*

FOR MODEL ZIDI240 WITH CUSTOM DRAWER PANELS AND HANDLES

Clearance for Door

Opening 2-1/2" min.

Countertop

Double-Drawer

23-1/8" min.

*Custom handle clearances may vary depending on the standoff of the

custom handles.

SIDE-BY-SIDE INSTALLATIONS –

Custom Panel Models Only

For a complete refreshment center, install a Double-Drawer

Refrigerator beside a Beverage Center or Wine Chiller/

Wine Reserve.

• A side-by-side installation requires at least a 47-1/2″wide

opening. No trim kits required.

• Products must operate from separate, properly grounded

receptacles.

34-1/2"-35"

24"

47-1/2" Min.

1-1/2"

10-1/2"

10-1/2" 14"

15"

Locate

Outlet

*NOTE: Additional clearances

may be required.

STEP 2 INSTALL CUSTOM 3/4″

DRAWER PANELS AND

HANDLES (ZIDI240 model only)

3/4″Overlay Panel Dimensions

Model ZIDI240 requires field-

installed overlay drawer panels.

• The overlay panels must be

secured to 1/4″thick backer

panels that slide into the trims.

A .10″thick spacer panel must

be placed between the overlay

and backer panels.

• Custom handles of your choice,

supplied by your cabinet maker,

must be installed on these overlay panels. Countersink

all screws into the backer panels. Screws cannot

protrude from the backer panels.

IMPORTANT NOTE: Maximum total weight for

custom drawer panels are 25 pounds (12-1/2 pounds

maximum each drawer).

Assemble overlay panels with

glue and screws.

• Center spacer panel on the

backer panel, left to right

and top to bottom. Secure

the panels with glue.

• Center the spacer/backer

panel on the overlay panel. Secure with glue and

screws. Countersink all screws into the backer panel.

3/4″Overlay Panel Dimensions (in inches)

A (Width) B (Height)

1/4″Backer 23-3/16″14-11/16″

0.10″Spacer 22-1/2″14-3/16″

3/4″Overlay 23-5/8″15-1/16″

STEP 1 REMOVE PACKAGING

• Remove corner blocks and foam drawer stops.

• Remove all packing material, tape and protective

plastic coverings.

CAUTION: Small objects are a choke

hazard for children. Remove and discard any parts

not used.

ATTENTION : Les petits objets

peuvent étrangler les enfants. Il faut jeter toutes

les piéces qui ne sont pas utilisées.

Overlay

Panel

1/4"

Backer

Panel

Drawer

.10 Inch

Spacer

Spacer Panel

Backer Panel

Overlay Panel

STEP 2 INSTALL CUSTOM 3/4″

DRAWER PANELS AND

HANDLES (CONT.)

(ZIDI240 model only)

Install custom drawer panels and handles:

• Open drawers.

• Remove 2 screws holding each trim; lift trims off.

Retain screws.

• Custom handles of your choice, supplied by your

cabinet maker, must be installed onto the overlay

panels before they are slid into the trims.

Countersink all screws into the backer panels.

Screws cannot protrude from the backer panels.

• Slide overlay panels into the trims.

Installation Instructions

Handle

Custom

Drawer Panel

Screws Must

Be Countersunk

Into Panel

12-1/2 lbs. max.

*Maintain a 1/4″min. gap between

top and bottom drawer panels.

STEP 2 INSTALL CUSTOM 3/4″

DRAWER PANELS AND

HANDLES (CONT.)

(ZIDI240 model only)

• Reinstall the side trims using the trim screws

removed earlier.

• Place the brushed decorative covers over the side

trim to hide the screw heads. Ensure side trim is

aligned top to bottom and front to back. Snap into

place.

NOTE: For shipping purposes the brushed decorative

cover will be secured to the front of the unit.

Installation Instructions

STEP 3 LEVEL

Use an adjustable wrench to turn and raise or lower

the leveling legs.

• Measure floor to countertop height inside the

opening. Adjust leveling legs until the product is

approximately 1/8″less than countertop height.

INSTALLATION TIP:

Measure floor to underside of countertop inside

the opening.

• If the room floor is higher than the floor inside

the opening, adjust the rear leveling legs to

approximately 1/8″less than the opening height.

Screw front leveling legs all the way in to shorten

the height at the front. This will allow you to slightly

tip the unit into the opening. Once the unit is in

the correct position, the front legs can be adjusted

to level the product.

Turn Right to Lower

Turn Left to Raise

Pub. No. 31-51545-1

Part No. 197D5893P003

02-04 JR

Printed in Slovenia

NOTE: While performing installations described in this book,

safety glasses or goggles should be worn.

For Monogram®local service in your area, call

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor

at General Electric. Therefore, materials, appearance

and specifications are subject to change without notice.

STEP 5 SLIDE PRODUCT INTO

THE CUTOUT

CAUTION: Do not push against the

drawer panels with your knees. Do not push or lift

the unit by the drawer handles. Damage may occur!

ATTENTION : Ne poussez jamais les

panneaux de tiroir avec vos genoux. Ne poussez

jamais votre appareil ou ne le soulevez jamais par

les poignées de tiroir. Vous pouvez l'endommager.

• Open one of the drawers and gently push the unit

back into the opening with your hands against the

sides. Be careful not to entangle power cord.

• Check again to be sure the unit is level. Adjust the

leveling legs until the unit is resting firmly against

the bottom of the counter to prevent rocking or

movement during operation.

• If alignment with adjacent cabinetry is an issue,

use a shim to secure the unit against the underside

of the countertop.

STEP 4 CONNECT POWER

• Connect power cord plug to a properly grounded

receptacle.

• Check to make sure power is on by opening a

drawer to see if interior light turns on.

• The interior fan runs all the time except when a

drawer is open.

See the Owner’s Manual for further explanation of

the fan.

STEP 6 SET TEMPERATURE

CONTROLS

• The temperature controls are preset. Refer to

the Owner’s Manual for more information. Allow

12–24 hours for the temperature to stabilize.

NOTE: The Double-Drawer Refrigerator operates

very quietly. You may not notice the unit running,

and when first installed, the fans and motor may not

come on immediately – this is normal. If the display

is lit and the light is working, the unit is operating.

Installation Instructions

Andere Handbücher für ZIDI240

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monogram Kühlschrank Handbücher

Monogram

Monogram 224D3094P002 Bedienungsanleitung

Monogram

Monogram Monogram ZISW36DRC Bedienungsanleitung

Monogram

Monogram ZICS360NHLH Bedienungsanleitung

Monogram

Monogram ZFSB25DXSS Bedienungsanleitung

Monogram

Monogram ZKST300N Leitfaden

Monogram

Monogram ZIC36NMALH Bedienungsanleitung

Monogram

Monogram Monogram ZISB480DR Benutzerhandbuch

Monogram

Monogram ZISP480DHSS Bedienungsanleitung

Monogram

Monogram ZISS420DHSS Gebrauchsanweisung

Monogram

Monogram ZIFS360 Bedienungsanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ZIRNPKII Bedienungsanleitung

Monogram

Monogram ZIBI240 Bedienungsanleitung

Monogram

Monogram Monogram ZIBI240PII Benutzerhandbuch

Monogram

Monogram 36 Ceramic Cooktop Bedienungsanleitung

Monogram

Monogram ZIR360NNRH Bedienungsanleitung

Monogram

Monogram ZISB360DH Bedienungsanleitung

Monogram

Monogram ZISS480DXASS Bedienungsanleitung

Monogram

Monogram ZISB42E Bedienungsanleitung

Monogram

Monogram GE RPWFE Bedienungsanleitung

Monogram

Monogram ZIDI240 Leitfaden

Monogram

Monogram Side-by-Side Stainless Steel Free-Standing Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram ZIPP360NHSS Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung