Monogram ZIP360NH Bedienungsanleitung

Product Specication Revised 5/15

Monogram®36" Built-In French-door Bottom-freezer

SECTION 1

ZIP360NH

SECTION 2

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

FLUSH INSET INSTALLATION

STANDARD INSTALLATION

OVERALL DIMENSIONS

AFTER PANEL INSTALL

Product Specication Revised 5/15

Monogram®36" Built-In French-door Bottom-freezer

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An individual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

SPECIFICATIONS

Overall Width 38" (96.5 cm)

Overall Height 84 1/2" (214.6 cm)

Overall Depth 25 7/8" (49.5 cm)

Door Clearance 19 1/2" (49.5 cm)

Cutout Width 39" (99.1 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Electrical Requirements 115 V AC, 60 Hz

20 amp circuit

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 663 lb (300.7 kg)

ZIP360NH

38" (96.5)

10 13/16"

(27.5)

7/16"

(1.1)

20 5/8" (52.4)

25 7/8" (65.7)

*84 1/2"

(214.6)

*73 5/16"

(186.2)

*4"

(10.2) SIDE VIEWFRONT VIEW

*83 1/2"

(212.1)

35" (89.0)

Case width

ZIP360NH

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan

access is maintained, but pan removal is restricted.

**8"

(20.3)

19 1/2"

(49.5)

TOP VIEW

*115° Door swing

**8"

(20.3)

*26 3/8"

(70.0)

7/16"

(1.1)

†Doors can be adjusted to

90° door swing

†Allow 4" (10.2) min

distance to adjacent

wall from cutout

†Allow 4" (10.2) min

distance to adjacent

wall from cutout

FLUSH INSET INSTALLATION

Product Specication Revised 3/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area

ZIP360NH

FLUSH INSTALLATION

ZIP360NH

39" (99.1) Flush inset width

37 1/2" (95.3)

Width between cleats

(15.2)

4 1/16"

(11.0)

(17.8)

10"

(25.4)

3/4" (1.9)

Width of side cleats

5 1/4" (13.3)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

3 1/2"

(8.9)

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

FRONT VIEWSIDE VIEW

TOP VIEW

WATER

3 1/2"

(8.9)

Finished cleats

Case Trim

3/4" Panel

Case

Door

85"

(215.9) 85"

(215.9)

FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION

ANTI-TIP BRACKET

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

The information below applies to all

installation constructions:

• A wall bracket, bolts and toggles will

be supplied with the unit.

• The bolts will be used to attach bracket

to wall in 4 locations. Two of the

locations must penetrate the center

of the wall studs.

• The toggles are used for stability in

drywall and when metal studs are

encountered. Lag bolts are used in

wood studs.

• In installation opening, measure

81 1/2" from oor and draw a

horizontal line.

• Locate and mark the wall studs on

horizontal line. Verify at least two

studs have their centerlines within the

center 32.5" of installation opening to

ensure 2 wall studs are penetrated.

• The bracket will be centered left to

right in opening with bottom of

bracket on the horizontal line.

• When unit is placed in opening, the

bracket tabs will align with openings

in back of the unit. The unit will be

secured to the bracket using supplied

“L” bolts.

See Installation Instructions for

detailed instructions.

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

centered

within the

cutout

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

Product Specication Revised 5/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

3/4" RAISED FRESH FOOD DOOR PANELS ROUTING

FLUSH INSET 3/4" PANEL DIMENSIONS

ZIP360NH

Grille Panel

Fresh

Food

Panel

Fresh

Food

Panel

Freezer Drawer Panel

E E

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed 1/2" or 3/4" custom door, drawer

and grille panels are required. For 3/4"

raised panels, routing is required. The router

depth is 1/4" all the way around the panel’s

backs. Additional panel width reductions

are required per the diagrams shown. This

will create “picture frame’ routing allowing

the panels to slide into the attached door,

drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 30 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

Door Handles

Door handles not included. Custom handles

supplied by your cabinet maker may be used.

ZKHFD2H: European tubular stainless steel

handles designed to t 3/4" panels. Kit

includes three handles.

FLUSH INSET INSTALLATION

A B C D E

38" 10 13/16" 46 7/16" 22 3/8" 18 3/4"

PANEL DIMENSIONS

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

3/4"

11/32"

1/4"

3/16"

1/4" 7/16"

DETAIL TOP

DETAIL BOTTOM

HINGE SIDE HANDLE SIDE

2 1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

3/16"

WARNING:

Door Trim Pinch Point Hazard

Improper installation can lead to a

nger pinch point hazard between the

side door trim and the cabinets when

operating the door, especially with

children. To minimize this risk you must

follow the installation instructions for

cabinet dimensions, trim assembly and

door stop angle.

Product Specication Revised 5/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

3/4" RAISED GRILLE PANEL ROUTING

3/4" RAISED FREEZER DRAWER PANEL ROUTING

ZIP360NH

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed 1/2" or 3/4" custom door, drawer

and grille panels are required. For 3/4"

raised panels, routing is required. The router

depth is 1/4" all the way around the panel’s

backs. Additional panel width reductions

are required per the diagrams shown. This

will create “picture frame’ routing allowing

the panels to slide into the attached door,

drawer and grille trims.

Maximum total panel weight:

• Fresh food door panels – 30 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

Door Handles

Door handles not included. Custom handles

supplied by your cabinet maker may be used.

ZKHFD2H: European tubular stainless steel

handles designed to t 3/4" panels. Kit

includes three handles.

FLUSH INSET INSTALLATION

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

3/4"

11/32"

1/4"

1/4" 1/2"

DETAIL TOP

DETAIL BOTTOM

1/4"

DETAIL TOP

DETAIL BOTTOM

ROUTER DEPTH 1/4"

1 11/16"

2 1/16" 2 1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

DETAIL

LEFT SIDE

DETAIL RIGHT

SIDE

2 1/16" 2 1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

DETAIL

LEFT SIDE

DETAIL RIGHT

SIDE

FLUSH INSTALLATION

ZIP360NH

39" (99.1) Flush inset width

37 1/2" (95.3)

Width between cleats

(15.2)

4 1/16"

(11.0)

(17.8)

10"

(25.4)

3/4" (1.9)

Width of side cleats

5 3/8" (13.7)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 13/16" (52.9)

Depth to cleat

3 1/2"

(8.9)

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

FRONT VIEWSIDE VIEW

TOP VIEW

WATER

3 1/2"

(8.9)

Finished cleats

Case Trim

1/2" Panel

Case

Door

85"

(215.9) 85"

(215.9)

Product Specication Revised 3/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area

ZIP360NH

FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET INSTALLATION

ANTI-TIP BRACKET

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

The information below applies to all

installation constructions:

• A wall bracket, bolts and toggles will

be supplied with the unit.

• The bolts will be used to attach bracket

to wall in 4 locations. Two of the

locations must penetrate the center

of the wall studs.

• The toggles are used for stability in

drywall and when metal studs are

encountered. Lag bolts are used in

wood studs.

• In installation opening, measure

81 1/2" from oor and draw a

horizontal line.

• Locate and mark the wall studs on

horizontal line. Verify at least two

studs have their centerlines within the

center 32.5" of installation opening to

ensure 2 wall studs are penetrated.

• The bracket will be centered left to

right in opening with bottom of

bracket on the horizontal line.

• When unit is placed in opening, the

bracket tabs will align with openings

in back of the unit. The unit will be

secured to the bracket using supplied

“L” bolts.

See Installation Instructions for

detailed instructions.

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

centered

within the

cutout

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

Product Specication Revised 5/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

FLUSH INSET1/2" PANEL DIMENSIONS

ZIP360NH

Grille Panel

Fresh

Food

Panel

Fresh

Food

Panel

Freezer Drawer Panel

E E

The 1/2" overlay panel must be secured to

a .10" spacer panel and a 1/4" thick backer

panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer

panel, left to right and top to bottom. Secure

the panels with glue.

• Refer to the chart for locating the backer

panel to the overlay panel. Secure the

overlay panel to the backer panel with glue

and screws. Screws must be countersunk

into the backer panel.

Maximum total panel weight:

• Fresh food door panel – 30 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs.

FLUSH INSET INSTALLATION

PANEL DIMENSIONS

A B C D E

1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16 21 7/8" 16 1/2"

.10" Space Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2" 15"

1/2" Overlay Panel 38" 10 13/16" 46 7/16" 22 3/8" 18 3/4"

A B C D

Fresh Food Door Panels 2 1/16" 3/16" 3/16" 3/16"

Freezer Drawer Panel 2 1/16" 2 1/16" 1/4" 1/4"

Grille Panel 2 1/16" 2 1/16" 1 11/16" 1/4"

PANEL DIMENSIONS

1/4" BACKER ASSEMBLY DIMENSIONS

Hinge Side

Backer with

Overlay Panel

Assembly

Fresh Food

Back

Fresh Food

Back

1/2"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

Freezer Drawer

A B

Grille Back

WARNING:

Door Trim Pinch Point Hazard

Improper installation can lead to a

nger pinch point hazard between the

side door trim and the cabinets when

operating the door, especially with

children. To minimize this risk you must

follow the installation instructions for

cabinet dimensions, trim assembly and

door stop angle.

OVERALL DIMENSIONS

AFTER PANEL INSTALL

Product Specication Revised 5/15

Monogram®36" Built-In French-door Bottom-freezer

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

*Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An individual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

ZIP360NH

STANDARD INSTALLATION

SPECIFICATIONS

Overall Width 36" (91.4 cm)

Overall Height 84" (213.4 cm)

Overall Depth 25 3/8" (64.5 cm)

Door Clearance 18 3/16" (46.2 cm)

Cutout Width 35 1/2" (90.2 cm)

Cutout Height 84" (213.4 cm)

Cutout Depth 24" (61 cm)

Electrical Requirements 115 V AC, 60 Hz

20 amp circuit

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 614 lb

*84"

(213.4)

FRONT VIEW

*73 1/4"

(186.1)

*26 7/16"

(67.1)

1/2"

(1.3)

9/16"

(1.4)

9 7/8"

(25.1)

46 5/16"

(117.7)

36" (91.4)

25 3/8" (64.5)

23 13/16" (60.5)

*4 1/8"

(10.5) SIDE VIEW

1 5/8"

(4.1)

*83 1/2"

(212.1)

**11 13/16"

(30.0)

**11 13/16"

(30.0)

18 3/16"

(46.2)

TOP VIEW

(SHOWING DOOR SWING)

35" (89.0)

Case width

ZIP360NZ

**130° Door swing

†Doors can be adjusted to

90° door swing

†Allow 4" (10.2) min

distance to adjacent

wall from cutout

†Allow 4" (10.2) min

distance to adjacent

wall from cutout

Product Specication Revised 3/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

STANDARD INSTALLATION 3/4" PANELS

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area

ZIP360NH

STANDARD INSTALLATION

STANDARD_INSTALLATION

ZIP360NH

24" (61)

1 9/16"

(3.97)

3 1/8"

(7.93) 35 1/2" (90.2)

2 5/16"

(5.874)

7/16" (1.1)

Trim overlap

3 1/2"

(8.9)

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

*84"

(213.4)

*Trim will overlap

additional 7/16"

(15.24)

10"

(25.4)

ELEC.

SIDE VIEW FRONT VIEW

TOP VIEW

(12.7)

WATERW

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

The information below applies to all

installation constructions:

• A wall bracket, bolts and toggles will

be supplied with the unit.

• The bolts will be used to attach

bracket to wall in 4 locations. Two

of the locations must penetrate the

center of the wall studs.

• The toggles are used for stability in

drywall and when metal studs are

encountered. Lag bolts are used in

wood studs.

• In installation opening, measure

81 1/2" from oor and draw a

horizontal line.

• Locate and mark the wall studs on

horizontal line. Verify at least two

studs have their centerlines within the

center 32.5" of installation opening to

ensure 2 wall studs are penetrated.

• The bracket will be centered left

to right in opening with bottom of

bracket on the horizontal line.

• When unit is placed in opening, the

bracket tabs will align with openings

in back of the unit. The unit will be

secured to the bracket using supplied

“L” bolts.

See Installation Instructions for

detailed instructions.

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

centered

within the

cutout

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

ANTI-TIP BRACKET

Grille Panel

Fresh

Food

Panel

Fresh

Food

Panel

Freezer Drawer Panel

E E

Door

1/4" Framed Panel

Supplied Handles

Trim

A B C D E

1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"

PANEL ASSEMBLY CROSS SECTION

PANEL DIMENSIONS

Product Specication Revised 3/15

Monogram®36" Built-In French-door Bottom-freezer

NOTES

Trimmed refrigerators are designed to be

customized with decorative panels Field-

installed custom door and grille panels

are required.

1/4" Framed Panels:

For 1/4" thick custom panels ordered from

your cabinet maker. The decorative panels

slide into this trim.

Maximum total panel weight:

• Fresh food door panel – 30 lbs.

• Freezer drawer panel – 28 lbs.

• Grille panel – 11 lbs

Door Handles:

The supplied handles accommodate both

framed or overlay panels. Custom handles

of your choice, supplied by your cabinet

maker, can also be installed.

STANDARD 1/4" FRAMED PANEL DIMENSIONS

ZIP360NH

STANDARD INSTALLATION

Andere Handbücher für ZIP360NH

Inhaltsverzeichnis

Andere Monogram Kühlschrank Handbücher

Monogram

Monogram Monogram ZIBI240PII Bedienungsanleitung

Monogram

Monogram 21 Bedienungsanleitung

Monogram

Monogram ZIDS240HSS Bedienungsanleitung

Monogram

Monogram 36 Ceramic Cooktop Bedienungsanleitung

Monogram

Monogram ZIPP360NHSS Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram Bottom-Freezer Built-In Refrigerators Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram ZIBI240HII Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram ZlS360N Bedienungsanleitung

Monogram

Monogram ZISP480DHSS Bedienungsanleitung

Monogram

Monogram WX08X10002 Bedienungsanleitung

Monogram

Monogram ZFSB25D SS Bedienungsanleitung

Monogram

Monogram Built-in refrigerators Bedienungsanleitung

Monogram

Monogram Monogram ZFSB25DSS Bedienungsanleitung

Monogram

Monogram 224D3735P001 Bedienungsanleitung

Monogram

Monogram ZDOD240HSS Bedienungsanleitung

Monogram

Monogram ZICP360NHRH Bedienungsanleitung

Monogram

Monogram 36 Ceramic Cooktop Bedienungsanleitung

Monogram

Monogram ZICP720 Bedienungsanleitung

Monogram

Monogram ZWE23 Bedienungsanleitung

Monogram

Monogram ZICS360NXLH Kurzanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung