Monogram Zis420nh Bedienungsanleitung

SECTION 1

Product Speciﬁcation Created 1/15

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

SECTION 2

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

FLUSH INSET INSTALLATION

STANDARD INSTALLATION

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

SPECIFICATIONS

Overall Width 44" (111.8 cm)†

Overall Height 84 1/2" (214.6 cm) †

Overall Depth 26" (66.0 cm) †

Door Clearance 26 5/8" (67.6 cm)

Cutout Width 45" (114.3 cm)

Cutout Height 85" (215.9 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 725 lb (328.9 kg)

FLUSH INSET INSTALLATION

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An individual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

44" (111.8)

84 1/2"

(214.6)

72 5/8"

(184.5)

68 5/8"

(174.3)

ZIS420NH

FRONT VIEW

11 11/16"

(29.7)

20 5/8" (52.4)

26" (66.0)

*4"

(10.2) SIDE VIEW

*83 1/2"

(212.1)

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan

access is maintained, but pan removal is restricted.

41" (104.2)

Case width

**13"

(33.0)

**19"

(48.3)

** Allow 4" (10.2) min

clearance to a wall

for 90˚ door swing

26 5/8"

(67.6)

** Allow 4" (10.2) min

clearance to a wall

for 90˚ door swing

TOP VIEW

*115° Door swing

Doors can be adjusted to

90° door swing

* Shipping height. Use leveling legs and wheels for maximum 1" height

adjustment from shipping height. Nominal installation height is 84".

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Product Speciﬁcation Created 1/15

OVERALL DIMENSIONS

AFTER PANEL INSTALL

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area.

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

Determine your installation

construction and required anti-tip

conﬁguration:

CCut a 1" x 4" block 35” long.

Measure and

mark under the sofﬁt,

5 1/4" from the front edge of the

cabinet. Secure the wood block

under the sofﬁt. From the bottom of

the block to the ﬁnished ﬂoor should

measure 84".

DWooden Wall Studs and No Sofﬁt

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of

opening at 84" or your installation

height from the ﬂoor.

See Installation Instructions for

detailed instructions.

NOTES

FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION

FLUSH INSTALLATION

ZISB420DH

45" (114.3) Flush inset width

43 1/2" (110.5)

Width between cleats

(17.8)

3/4" (1.9)

Width of side cleats

5 1/4" (13.3)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

WATER

3 1/2"

(8.9)

Finished cleats

Case Trim

3/4" Panel

Case

Door

19"

(48.3)

(12.7)

(15.2) E

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

85"

(215.9) 85"

(215.9)

ANTI-TIP BRACKET

FRONT VIEW SIDE VIEW

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16" (1.1)

Trim overlap

3 1/2"

(8.9)

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

(15.2)

(12.7)

ZISB480DX

SIDE VIEW INSTALLED

UNDER SOFFIT

SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

*84"

(213.4)

*Or installation

height from floor

2" x 4"

Cut to 35" Length

Screws mounted

into vertical wall

studs

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Product Speciﬁcation Created 1/15

AMounting the junction box in this

location will also allow for front

accessibility through access panel.

BWater supply area.

WARNING:

The refrigerator is top heavy and must

be secured to prevent the possibility of

tipping forward. Failure to do so may

result in death or serious injury.

The information below is for cabinet

design only. When installing the anti-

tip system you must use the product

installation instructions.

Determine your installation

construction and required anti-tip

conﬁguration:

CCut a 1" x 4" block 35” long. Measure

and mark under the sofﬁt,

5 3/8" from the front edge of the

cabinet. Secure the wood block

under the sofﬁt. From the bottom of

the block to the ﬁnished ﬂoor should

measure 84".

DWooden Wall Studs and No Sofﬁt

• Cut a 2" x 4" block and secure to

brackets provided.

• Secure brackets to back wall of

opening at 84" or your installation

height from the ﬂoor.

See Installation Instructions for

detailed instructions.

NOTES

FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET INSTALLATION

FLUSH INSTALLATION

ZISB420DH

45" (114.3) Flush inset width

43 1/2" (110.5)

Width between cleats

(17.8)

3/4" (1.9)

Width of side cleats

5 3/8" (13.7)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 13/16" (52.9)

Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

WATER

3 1/2"

(8.9)

Finished cleats

Case Trim

1/2" Panel

Case

Door

19"

(48.3)

(12.7)

(15.2) E

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

85"

(215.9) 85"

(215.9)

ANTI-TIP BRACKET

FRONT VIEW SIDE VIEW

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16" (1.1)

Trim overlap

3 1/2"

(8.9)

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

(15.2)

(12.7)

ZISB480DX

SIDE VIEW INSTALLED

UNDER SOFFIT

SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

*84"

(213.4)

*Or installation

height from floor

2" x 4"

Cut to 35" Length

Screws mounted

into vertical wall

studs

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Product Speciﬁcation Created 1/15

A B C D E

44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

PANEL DIMENSIONS

FLUSH INSET 3/4" PANEL DIMENSIONS FLUSH INSET INSTALLATION

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Grille Panel

Freezer

Panel

Fresh

Food

Panel

D E

3/4" RAISED DOOR PANEL ROUTING

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

HINGE

SIDE

HANDLE

SIDE

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

3/4"

11/32"

1/4"

3/32"

1/4" 11/32"

DETAIL TOP

DETAIL BOTTOM

2 1/16" 3/16"

ROUTER DEPTH 1/4"

DETAIL HINGE

SIDE

DETAIL HANDLE

SIDE

Product Speciﬁcation Created 1/15

NOTES

Trimmed refrigerators are designed

to be customized with decorative panels.

Field-installed 1/2" or 3/4" custom door

and grille panels are required. For 3/4"

raised door and grille panels, routing is

required. The router depth is 1/4" all the

way around the panel’s backs. Additional

panel width reductions are required per

the diagrams shown. This will create

“picture frame” routing allowing the

panels to slide into the attached door and

grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Door Handles

Door handle not included. A custom

handle supplied by your cabinet maker

may be used.

ZKHPSS1: Professional tubular stainless

steel handle designed to ﬁt 3/4" panels.

Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel

handle designed to ﬁt 3/4" panels. Kit

includes one handle – 64 1/4" long.

NOTES

Trimmed refrigerators are designed

to be customized with decorative

panels. Field-installed 1/2" or 3/4"

custom door and grille panels are

required. For 3/4" raised door and grille

panels, routing is required. The router

depth is 1/4" all the way around the

panel’s backs. Additional panel width

reductions are required per the diagrams

shown. This will create “picture frame”

routing allowing the panels to slide into

the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

Door Handles

Door handle not included. A custom

handle supplied by your cabinet maker

may be used.

ZKHPSS1: Professional tubular stainless

steel handle designed to ﬁt 3/4" panels.

Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel

handle designed to ﬁt 3/4" panels. Kit

includes one handle – 64 1/4" long.

FLUSH INSET INSTALLATION

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

3/4" RAISED GRILLE PANEL ROUTING

Front

NOTE: Routed areas should be

finished as they may be visible

when assembled.

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

Back

TOP

FrontBack

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

3/16"

DETAIL TOP

DETAIL BOTTOM

ROUTER DEPTH 1/4"

2 1/16" 2 1/16"

ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"

DETAIL

LEFT SIDE

DETAIL RIGHT

SIDE

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

LEFT

SIDE

RIGHT

SIDE

Front

Back

Product Speciﬁcation Created 1/15

A B C D E

1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

.10" Space Panel 39" 8 5/8" 67" 13 9/16" 23 9/16"

1/2" Overlay Panel 44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

A B C D

Fresh Food Panel 2 1/16" 1/16" 1/8" 1/8"

Freezer Panel 2 1/16" 1/16" 1/8" 1/8"

Grille Panel 2 1/16" 2 1/16" 1 15/32" 7/32"

PANEL DIMENSIONS

FLUSH INSET 1/2" PANEL DIMENSIONS

The 1/2" overlay panel must be secured to

a .10" spacer panel and a 1/4" thick backer

panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer

panel, left to right and top to bottom.

Secure the panels with glue.

• Refer to the chart for locating the backer

panel to the overlay panel. Secure the

overlay panel to the backer panel with glue

and screws. Screws must be countersunk

into the backer panel.

Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs.

FLUSH INSET INSTALLATION

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Grille Panel

Freezer

Panel

Fresh

Food

Panel

D E

NOTES

1/4" BACKER ASSEMBLY ROUTING DIMENSIONS

Freezer

Back

Hinge Side

Fresh Food

Back

Backer with

Overlay Panel

Assembly

AAB B

1/2"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

A B

Grille Back

Product Speciﬁcation Created 1/15

OVERALL DIMENSIONS

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

STANDARD INSTALLATION

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An individual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

SPECIFICATIONS

Overall Width 42" (106.7 cm)

Overall Height 84" (213.36 cm)

Overall Depth 25 3/8" (64.453 cm)

Door Clearance 26 5/8" (67.6 cm)

Cutout Width 41 1/2" (105.4 cm)

Cutout Height 83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

Cutout Depth 24" (61 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 725 lb (328.9 kg)

*84"

(213.4)

42" (106.7)

25 1/2" (64.8)

23 7/8" (60.7)

1 3/4"

(4.4)

*72 1/4"

(183.5)

*3 1/2"

(8.9)

*83 1/2"

(212.1)

68 1/2"

(174.0)

*3 3/4"

(9.5)

41" (104.2)

Case width

26 5/8"

(67.6)

ZIS420NX

TOP VIEW

SIDE VIEWFRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

** Allow 13" (33.0) min

clearance for 130˚

door swing

** Allow 19" (48.3) min

clearance for 130˚

door swing

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

full 130° door swings for pan removal. If the 90° door stop position is used, pan access is

maintained, but pan removal is restricted.

*84"

(213.4)

42" (106.7)

25 1/2" (64.8)

23 7/8" (60.7)

1 3/4"

(4.4)

*72 1/4"

(183.5)

*3 1/2"

(8.9)

*83 1/2"

(212.1)

68 1/2"

(174.0)

*3 3/4"

(9.5)

41" (104.2)

Case width

26 5/8"

(67.6)

ZIS420NX

TOP VIEW

SIDE VIEWFRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

** Allow 13" (33.0) min

clearance for 130˚

door swing

** Allow 19" (48.3) min

clearance for 130˚

door swing

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

** Allow 4" (10.2) min

clearance to a wall for 90˚

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

full 130° door swings for pan removal. If the 90° door stop position is used, pan access is

maintained, but pan removal is restricted.

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Product Speciﬁcation Created 1/15

STANDARD INSTALLATION

ZISB420DH

24" (61)

1 9/16"

(3.97)

3 1/8"

(7.93) 41 1/2" (105.4)

7/16" (1.1)

Trim overlap

3 1/2"

(8.9)

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

*84 1/2"

(214.6)

*Trim will overlap

additional 7/16"

SIDE VIEW FRONT VIEW

TOP VIEW

(12.7)

WATERW

18" (45.7)

(15.24)

(12.7)

NOTES

STANDARD INSTALLATION STANDARD INSTALLATION

ANTI-TIP BRACKET

FRONT VIEW SIDE VIEW

24" (61.0)

1 1/2"

(3.8)

3 1/4"

(8.3)

7/16"

(1.1)

Trim overlap

3 1/2"

(8.9)

WATER

47 1/2" (120.7)

20" (50.8)

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

(15.2)

(12.7)

ZISB480DX

SIDE VIEW INSTALLED

UNDER SOFFIT

SOFFIT

SIDE VIEW INSTALLED

WITH WOODEN WALL STUDS

AND NO SOFFIT

*84"

(213.4)

*Or installation

height from floor

2" x 4"

Cut to 35" Length

Screws mounted

into vertical wall

studs

FRONT VIEW INSTALLED

WITH METAL WALL STUDS

AND NO SOFFIT

Top Case Trim

3/4"

Min.

Side View Top

Case Trim

Install Screws

Through Trim and Into

3/4" Min. Wood Brace

The refrigerator

will project

forward, slightly

beyond adjacent

cabinetry.

AMounting the junction

box in this location will

also allow for front

accessibility through

access panel.

BWater supply area.

WARNING:

The refrigerator is top

heavy and must be secured

to prevent the possibility of

tipping forward. Failure to

do so may result in death

or serious injury.

The information below is

for cabinet design only.

When installing the anti-

tip system you must use

the product installation

instructions.

Determine your installation

construction and required

anti-tip conﬁguration:

CInstalled Under Sofﬁt

After installing unit into

installation opening,

raise grille panel and

screw metal case sides to

adjacent cabinet. When

installed under a sofﬁt, the

sofﬁt cannot exceed 24"

deep. The top case trim

overlaps the bottom of the

sofﬁt.

DWooden Wall Studs and

No Sofﬁt

• Cut a 2" x 4" block and

secure to brackets

provided.

• Secure brackets to back

wall of opening at 84" or

your installation height

from the ﬂoor.

EMetal Wall Studs and

No Sofﬁt

This method requires

securely fastened cabinets

on both sides and a 3/4"

minimum wood brace

above unit, with it’s front

surface 24" from back wall.

• After installing unit into

opening, raise grille panel

and attach metal case

top trim to 3/4" minimum

wood brace.

• The brace spanning

the enclosure must be

securely fastened to

cabinets on both sides.

See Installation

Instructions for detailed

instructions.

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Product Speciﬁcation Created 1/15

CUSTOM SIDE PANELS

2 9/16"

(6.5)

*3" - 4"

(7.6 - 10.2)

*Depending

on installation

height

1 7/8"

(4.8)

24" (61.0)

3/16"

(.5)

*84”

(213.4)

*Depending

on installation

*84"

(213.4)

*Depending

on installation

height

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

NOTES

STANDARD INSTALLATION

FSide panels must be used whenever

the sides of the refrigerator will be

exposed. The 1/4" side panels will

slip into the side case trim. Secure

the panels to the refrigerator with

stick-on hook and loop fastener

strips. Order the side panels from

the cabinet manufacturer.

ZIS420NHMonogram®42" Built-In Side-by-Side Refrigerator

Product Speciﬁcation Created 1/15

Inhaltsverzeichnis

Andere Monogram Kühlschrank Handbücher

Monogram

Monogram ZISB360DH Bedienungsanleitung

Monogram

Monogram ZISB42DY Bedienungsanleitung

Monogram

Monogram ZWE23 Bedienungsanleitung

Monogram

Monogram ZIDI240 Bedienungsanleitung

Monogram

Monogram Side-by-Side Stainless Steel Free-Standing Bedienungsanleitung

Monogram

Monogram ZIS42 Bedienungsanleitung

Monogram

Monogram 224D3094P002 Bedienungsanleitung

Monogram

Monogram ZDOD240 Bedienungsanleitung

Monogram

Monogram Side-by-Side36" Bedienungsanleitung

Monogram

Monogram Double-Door Bedienungsanleitung

Monogram

Monogram Monogram ZFSB26DRSS Benutzerhandbuch

Monogram

Monogram ZDOG240 Bedienungsanleitung

Monogram

Monogram Monogram ZIBI240PII Bedienungsanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ZISW36DY Bedienungsanleitung

Monogram

Monogram ZIFI240 Bedienungsanleitung

Monogram

Monogram ZFGB21HZBSS Bedienungsanleitung

Monogram

Monogram ZICS360NRFRH Bedienungsanleitung

Monogram

Monogram ZICP360NHRH Bedienungsanleitung

Monogram

Monogram ZICS36N RH Bedienungsanleitung

Monogram

Monogram ZDOD240 Bedienungsanleitung

Monogram

Monogram ZIR300NPKII Bedienungsanleitung

Monogram

Monogram ZIF360NHXH Bedienungsanleitung

Monogram

Monogram ZISB420DH Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Monogram zis420nh Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken