Monoprice 36373 Bedienungsanleitung

Commercial Audio

60-Watt 70V/100V Mixer Amplifier

P/N 36373

User's Manual

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these

safety warnings and guidelines. Please keep this manual in a safe place for future

reference.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks

or other containers with moisture on or near the device. If moisture does get in

or on the device, immediately unplug it from the power outlet and allow it to

fully dry before reapplying power.

Do not touch the device, the power cord, or any other connected cables with

wet hands.

Do not expose this device to excessively high temperatures. Do not place it in,

on, or near a heat source, such as a fireplace, stove, radiator, etc. Do not leave it

in direct sunlight.

This device ventilates excessive heat through the slots and openings in the case.

Do not block or cover these openings. Ensure that the device is in an open area

where it can get sufficient airflow to keep from overheating.

Do not place or install this device in an area where it can be exposed to

excessive amounts of dust, humidity, oil, smoke, or combustible vapors.

Use only in a well-ventilated area. Do not use in close, confined spaces.

Prior to operation, check the unit and power cord for physical damage. Do not

use if physical damage has occurred.

Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

This device uses a grounded power cord and requires a ground connection for

safe operation. Ensure that the power source has a proper ground connection.

Do not modify the plug or use a "cheater" plug to bypass the ground connection.

Unplug this device from the power source when not in use.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that

the power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

Ensure that power is turned off and disconnected before making any electrical

connections.

Remove the batteries from the controller if it will go unused for a lengthy period

of time.

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

This device has no user serviceable parts. Do not attempt to open, service, or

modify this device.

INTRODUCTION

Thank you for purchasing this Commercial Audio 60-Watt 70V/100V Mixer Amplifier!

This amplifier is designed to drive a conventional 4-ohm, 8-ohm, or 16-ohm speaker

system, as well as 70-volt and 100-volt constant voltage speaker systems. It features

one unbalanced 1/4" microphone input, one balanced XLR microphone input (which can

be switched to an unbalanced RCA line level input), and one additional unbalanced RCA

line level input. Enjoy background music in your facility by using the included

Bluetooth® receiver or the built-in FM tuner.

FEATURES

Compact public address amplifier

Supports 4-ohm, 8-ohm, and 16-ohm passive speakers

Supports 70-volt and 100-volt constant voltage speaker systems

Delivers 60-watts into a 4 ohm load

Built-in mp3 player, FM tuner, and Bluetooth® connection

Includes 1/4" unbalanced and XLR balanced microphone inputs

Supports phantom power for condenser microphones

Includes two line inputs and one line output

Features an EMC priority input

Includes short circuit, clipping, overload, and over temperature protection

circuits

Can accept 100 ~ 240 VAC, 50/60 Hz or 24 VDC, 4A input power

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your

ordering, purchasing, and delivery experience is second to none. If you have any

problem with your order, please give us an opportunity to make it right. You can

contact a Monoprice Customer Service representative through the Live Chat link on our

website www.monoprice.com or via email at su[email protected]. Check the

website for support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service

for a replacement.

1x Commercial audio public address amplifier

1x IR remote control

1x FM antenna

1x 4P 5.08mm wiring terminal

2x 2P 3.81mm wiring terminal

1x User's manual

PRODUCT OVERVIEW

Front Panel

1. Display: Displays input, track, and FM radio frequency information.

2. USB: USB port for use with a USB flash drive containing mp3 tracks to playback

with the built-in mp3 player. The USB port supports USB drives up to 128GB in

size.

3. Play/Pause: When in mp3 or Bluetooth® mode, momentarily press the button to

play, pause, and resume playback. When in FM radio mode, press the button to

scan for available radio stations.

4. Previous: When in USB and Bluetooth modes, momentarily press the button to

skip back to the previous track. When in FM radio mode, momentarily press the

button to go back to the previous radio station. In all modes, press and hold the

button to reduce the volume level.

5. Next: When in USB and Bluetooth modes, momentarily press the button to skip

forward to the next track. When in FM radio mode, momentarily press the

button to go to the next radio station. In all modes, press and hold the button to

increase the volume level.

6. Mode: Momentarily press the button to cycle through the Bluetooth, USB, AUX

Input, and FM radio modes.

7. MIC1 Priority: 1/4" TS jack for use with a dynamic microphone. This input has

priority over all other inputs, except the EMC input.

8. MIC1: Adjusts the volume of the MIC1 input.

9. MIC2/AUX2: Adjusts the volume of the MIC2/AUX2 input.

10. AUX1: Adjusts the volume of the AUX1 input.

11. BASS: Adjusts the volume of low frequencies.

12. TREBLE: Adjusts the volume of high frequencies.

13. MASTER: Adjusts the volume level of all inputs, except the EMC input.

14. ON/OFF: Power switch to turn the amplifier on or off.

15. Indicators: The POWER LED illuminates when power is applied. The PROT LED

illuminates when one of the protective circuits is activated. The 2, 4, 6, and 8

LEDs indicate the output level.

Rear Panel

1. Power Cord: Plug the power cord into a nearby AC power outlet. This amplifier

accepts 110 ~ 240 VAC, 50/60 Hz, 4A.

2. FM ANT: Connector for attaching the included FM antenna.

3. DC IN: Alternative power input for use with a 24 VDC, 4A power source.

4. AMPLIFIER OUT: Terminals for connecting passive or constant voltage speaker

systems.

5. AUX OUT: Line level output RCA jacks.

6. AUX1 IN: Line level input RCA jacks.

7. AUX2 IN: Line level input RCA jacks.

8. AUX2/MIC2: Switch to select either the AUX2 line level input or the MIC2 input.

When the switch is in the MIC2 position, the XLR jack is configured for use with a

dynamic microphone. When set to the PHANTOM position, the XLR jack is

configured to provide +48V phantom power for use with a condenser

microphone.

9. +48V: The LED indicator illuminates when the AUX2/MIC2 switch is set to the

PHANTOM position for use with a condenser microphone.

10. MIC2: XLR jack for connecting a balanced dynamic or condenser microphone.

11. VOL: Gain control for the AUX2/MIC2 input.

12. 100V: Terminals for accepting a 100V emergency signal input.

13. VOL: Gain control for the EMC input.

14. EMC IN: Secondary 350mV emergency input.

Remote Control

1. Mode: Press the Mode button to cycle through

the Bluetooth®, USB, AUX Input, and FM radio

modes.

2. Power: Press the Power button to turn the

amplifier on or off.

3. Play/Pause: When in mp3 or Bluetooth® mode,

momentarily press the button to play, pause,

and resume playback. When in FM radio mode,

press the button to scan for available radio stations.

4. EQ: Press the EQ button to cycle through Normal, Pop, Rock, and Jazz EQ effects.

5. Numbers: When in FM radio mode, use the number buttons to directly input an

FM frequency.

6. Mute: Press the Mute button to turn audio muting on or off.

7. Previous: When in USB and Bluetooth modes, momentarily press the button to

skip back to the previous track. When in FM radio mode, momentarily press the

button to go back to the previous radio station.

8. Next: When in USB and Bluetooth modes, momentarily press the button to skip

forward to the next track. When in FM radio mode, momentarily press the

button to go to the next radio station.

9. Volume -: Press the button to decrease the volume level.

10. Volume +: Press the button to increase the volume level.

11. Cycle: Toggles between the Play All (once) and Repeat All play modes.

12. SCAN: Not used.

OPERATING MODES

Mic1

The MIC1 input has priority over all other inputs, except the EMC input. When a signal is

detected, the amplifier automatically mutes all other inputs. When the signal is

removed, the amplifier will return to normal playback mode.

Bluetooth

To activate Bluetooth® mode, press the MODE button until the word BLUE is displayed

on screen. If no paired device is found, the word BLUE will flash, indicating that it is in

Bluetooth pairing mode. To pair your mobile device, open the device's Bluetooth

settings, then scan for nearby devices. Locate and select the MP36373 entry.

USB

When a USB flash drive is inserted into the USB port, the amplifier will automatically

switch to USB mode and will use the built-in mp3 player to playback audio tracks from

the USB drive.

AUX

To select the line level input, press the MODE switch until the word AUX appears on

screen.

In FM mode, press the Play/Pause button on the front panel or on the remote control to

scan for available stations. Press the Previous button on the front panel or on the

remote control to skip back to the previous station. Press the Next button on the front

panel or on the remote control to skip to the next station. Use the number buttons on

the remote control to directly tune to a specific frequency.

SPECIFICATIONS

Model

36373

Output Power

60 watts into 4 ohms

Speaker Outputs

4-ohm, 8-ohm, 16-ohm, 70V, 100V

Inputs

1/4" TS unbalanced MIC1, RCA line level AUX1,

RCA line level AUX2, XLR balanced MIC2, EMC

Input Priority

EMC > MIC1 > all others

MIC1 Input Sensitivity

5mV

MIC2 Input Sensitivity

5mV

AUX1 Input Sensitivity

350mV

AUX2 Input Sensitivity

350mV

EMC Input Sensitivity

350mV

MIC Frequency Response

180 Hz ~ 10 kHz ±3dB

AUX Frequency Response

70 Hz ~ 16 kHz ±3dB

Noise

< 5mV (4 ohm load)

Total Harmonic Distortion

< 1% @ 1kHz

Treble and Bass Adjustment

10dB ±2dB

Protection Circuits

Short circuit, clipping, overload, over

temperature

Input Power

110 ~ 240 VAC, 50/60 Hz, 4A OR 24 VDC, 4A

Bluetooth® Pairing ID

MP36373

Dimensions

9.7" x 7.8" x 2.6" (247 x 198 x 66 mm)

Weight

5.7 lbs. (2.6 kg)

Inhaltsverzeichnis

Andere Monoprice Verstärker Handbücher

Monoprice

Monoprice WolfPack HDTVNOM18800 Bedienungsanleitung

Monoprice

Monoprice 38360 Bedienungsanleitung

Monoprice

Monoprice HS-102 Bedienungsanleitung

Monoprice

Monoprice 11567 Bedienungsanleitung

Monoprice

Monoprice CasaTunes CT-250A Bedienungsanleitung

Monoprice

Monoprice INDIO 611710 Gebrauchsanweisung

Monoprice

Monoprice Monolith 11X Bedienungsanleitung

Monoprice

Monoprice 13194 Bedienungsanleitung

Monoprice

Monoprice MONOLITH 7 Bedienungsanleitung

Monoprice

Monoprice 31027 Bedienungsanleitung

Monoprice

Monoprice SWA-400 Bedienungsanleitung

Monoprice

Monoprice 16154 Bedienungsanleitung

Monoprice

Monoprice Monolith 7X Bedienungsanleitung

Monoprice

Monoprice VX-8202F Bedienungsanleitung

Monoprice

Monoprice 39261 Bedienungsanleitung

Monoprice

Monoprice Cat5 x1 Bedienungsanleitung

Monoprice

Monoprice 18802 Bedienungsanleitung

Monoprice

Monoprice MONOLITH 33306 Bedienungsanleitung

Monoprice

Monoprice 13194 Bedienungsanleitung

Monoprice

Monoprice 18803 Bedienungsanleitung

Monoprice

Monoprice MP-SP18 Bedienungsanleitung

Monoprice

Monoprice Monolith 24460 Bedienungsanleitung

Monoprice

Monoprice PID 11498 Bedienungsanleitung

Monoprice

Monoprice Monolith M5100X Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung