Monoprice 27771 Bedienungsanleitung
User’s Manual
P/N 27771
Gaming Monitor
To assure the product to work in best status
Please read the user manual carefully before operation and
keep it well for use
27”
TABLE OF CONTENTS
A. INSTRUCTIONS
1. Safety Warnings and Guidelines
4. Package Contents
5. Installation
6. The Main Parts and Terminals
B.KEYPAD FUNCTION
8. Keypad Function
9. Quick Enter Keypad
C. MENU ADJUSTMENT
D. OTHERS
11. The Remote Control
15. Trouble Shooting
13. Product Specification
12. The LED Indicator
01
2. Features
3. Viewing Angle Adjustment
7. Setup
14. Compatible Video Resolutions
10. OSD Menu Map
SAFETY WARNINGS AND GUIDELINES
02
Please read this entire manual before using this device, paying extra
attention to these safety warnings and guidelines. Please keep this
manual in a safe place for future reference.
• Do not place the monitor on an unstable surface where it could fall
and cause either personal injury or damage to the monitor and/or
other equipment.
• Do not expose the monitor to water or moisture of any kind. Do not
place objects containing moisture, such as a glass or vase, where it
could tip over and spill into or onto the monitor.
• If the monitor is exposed to water or moisture, immediately unplug
it from its power source and allow it to completely dry out before
reapplying power.
• Do not block the ventilation holes in the monitor's casing. Do not
place the monitor in a confined space with inadequate ventilation.
• Do not place the monitor near a heat source, such as a fireplace,
heating vent, radiator, etc. Do not leave it in direct sunlight.
• The power supply for this monitor uses a NEMA 5-15 three prong,
grounded plug. Do not use a "cheater" plug or otherwise bypass the
grounding pin.
• The power supply for this monitor accepts a wide range of input
voltages, from 100 to 240 VAC, 50 or 60 Hz. Ensure that your power
source is within these limits. If not, consult a professional electrician
or your power company for a resolution.
• Unplug the monitor if it will go unused for a long period of time.
• This monitor has no user serviceable parts. Do not open the case or
otherwise attempt to modify this monitor.
• Clean using a soft, dry cloth only. Do not use chemical cleaners,
solvents, or detergents. For stubborn deposits, moisten the cloth
with warm water.
• Do not leave a single image on the display for a long period of time.
Doing so could cause "burn-in" of the image. It is recommended to
use a variable desktop background and to use a screen saver to
prevent "burn-in". Alternatively, ensure that the monitor is powered
off for at least 2 hours out of every 12.
03
FEATURES
• 3840 x 2160 maximum resolution
• 16:9 aspect ratio
• HDMI®, and DisplayPort video inputs
• +13°/0° tilt range using included stand
• 5ms response time
VIEWING ANGLE ADJUSTMENT
The included monitor stand supports tilt adjustment from -0° (down)
to +13° (up). To adjust the angle, grasp the bezel at both the top and
bottom of the monitor and move it as desired. Use soft cloth gloves or
a soft, dry cloth to grasp the monitor without touching the screen.
13°
Package Contents
1x Monitor
1x Stand Base
1x HDMI 2.0 Cable
1x AC Power Adapter
1x AC Power Cord
1x remote control 2x battery
04
1x User's Manual
6x Screws for Stand Base
User’s Manual
P/N 27771
Gaming Monitor
To assure the product to work in best status
Please read the user manual carefully before operation and
keep it well for use
27”
Installation
05
QUICK START GUIDE
Put the monitor face down on a stable and smooth surface, pay attention
not to damage or scratch the front glass / screen. It’s better putting a
soft piece of cloth on the table beforehand to protect the monitor. Make
sure the monitor is unplugged before starting installation.
SETTING UP THE MONITOR
1. Put the monitor face down on a stable and smooth surface; make sure
you have enough space to operate safely
2. Make sure you have the base kit with all his parts (7 screws / 3 stand
parts) to set up the monitor correctly.
Display The base kit
3. Secure the bracket and stand with the included screwdriver and screws as
per the below picture.
06
4. Put the base kit on the back side of the display as per the below picture.
Fix the stand kit to the back side of the monitor as per the above picture.
Screw without force.
5. Make sure the stand and base are firmly attached.
6. Make sure both monitor and computer are unplugged.
7. Plug power cord and signal cable (HDMI or DP) to the monitor.
8. Plug the computer and monitor power cord to the power supply.
9. Turn on the monitor and computer.
NOTE / CAUTION
After turning on computer and monitor if no image is displaying make sure you
have chosen the right signal cable.
Please make sure to earth the power cord.
Speaker Hole VESA hole
100mm x 100mm I/O Port
Keypad
Back
07
LED Indicator/IR
signal receiver Base Screen
Front
The Main Parts and Terminals
08
V- V+
HDMI : HDMI 2.0 version, maximum resolution 3840 x 2160 @60Hz.
DP: Display Port 1.2 version, maximum resolution 3840x2160@60Hz.
DC IN : 12V Please use only the power DC adaptor and power cord included
in Package.
Please refer to the below picture for the definition of the DC port
The Main Parts and Terminals
SETUP
1. If you will be using the desk stand, use a Phillips screwdriver and the
four included Screws to attach the Stand Base to the stand.
2. Using the included DisplayPort cable, plug one end into the Display
Port input on the monitor, then plug the other end into the Display
Port output on your computer.
3. Plug the DC barrel connector on the included AC Power Adapter into
the DC IN connector on the monitor.
4. Plug the C13 included AC Power Cord into the AC Power Adapter,
then plug the other end into a nearby AC power outlet.
DC INHDMI 2 HDMI 1DP 2 DP 1
AUDIO
OUT
AUDIO OUT : To be use when using HDMI or DP signal to get audio on
earphone or speakers.
09
Keypad on the front panel
Select Input Source：
1. Press the “Select”button, the main menu will
display on the screen.
2. Press the ▲ and ▼ to select a applicable input
source, and press the “V-” button or wait for 3
seconds to perform the selection.
OSD Menu
OSD Menu
MENU
SELECT
V.+
V.-
▲
▼
HDMI 1
HDMI 2
DP 1
DP 2
Control Button Functions
MENU : Activates the menu, Selects the highlighted function.
SELECT: Select input source.
V.+： Increases Volume/Select sub-menu rightward.
V.- : Decrease Volume/Select sub-menu leftward.
▲ ：Moves highlight up, select the sub-menu .
▼ ：Moves highlight down, select the sub-menu .
：Turns monitor on/off.
Quick Enter function
▲ ： Press to adjust the aspect ratio.
▼ ： Press to display the Cross hair target .
Keypad
Inhaltsverzeichnis
Andere Monoprice Monitor Handbücher
Monoprice
Monoprice 6960 Bedienungsanleitung
Monoprice
Monoprice Zero-G 31004 Bedienungsanleitung
Monoprice
Monoprice CrystalPro 37922 Bedienungsanleitung
Monoprice
Monoprice DARK MATTER 44710 Bedienungsanleitung
Monoprice
Monoprice 43021 Bedienungsanleitung
Monoprice
Monoprice Crystal Pro 44029 Bedienungsanleitung
Monoprice
Monoprice Dark Matter 40778 Bedienungsanleitung
Monoprice
Monoprice Dark Matter H3C2R-HQ Bedienungsanleitung
Monoprice
Monoprice 16384 Bedienungsanleitung
Monoprice
Monoprice 38577 Bedienungsanleitung
Monoprice
Monoprice DARK MATTER 45548 Bedienungsanleitung
Monoprice
Monoprice 24657 Bedienungsanleitung
Monoprice
Monoprice 31006 Bedienungsanleitung
Monoprice
Monoprice 31005 Bedienungsanleitung
Monoprice
Monoprice 27772 Bedienungsanleitung
Monoprice
Monoprice 43021 Bedienungsanleitung
Monoprice
Monoprice Dark Matter 44632 Bedienungsanleitung
Monoprice
Monoprice 37924 Bedienungsanleitung
Monoprice
Monoprice 10707 Bedienungsanleitung
Monoprice
Monoprice 34in CrystalPro Curved 1000R VA Panel Bedienungsanleitung
