Monoprice Adjustable Tilt/Flat Panel Bedienungsanleitung

(PID# 4174)

VESA Compliant: Up to 600x400

Max Weight: 165lbs

Installation Instruction

UNPACKING INSTRUCTIONS

•Carefully open the carton, remove the contents and lay them out on cardboard or other protective surface to avoid

damage.

•Check the contents against the supplied parts list on the next page to assure that all components were received

undamaged. Do not use any damaged or defective parts.

IMPORTANT SAFETY INFORMATION

Install and use this device with care. Please read this entire manual before attempting installation and carefully follow all

instructions contained herein. Use proper safety equipment during installation.

Please call a qualified installation contractor for help if you:

•Don’t understand the instructions in this manual or have any doubts about the safety of the installation.

•You are uncertain about the nature of your wall.

Note: The mounting components and hardware supplied in this package are not designed for installation to wall with

steel studs or to cinder block walls. If the hardware you need for your installation is not included, please consult your local

hardware store for proper mounting hardware for this application.

CAUTION!

WARNING

Tools Required 3/16″ Drill Bit 1/2″ Masonry Bit Wrench or Socket Set

Carpenter’s LevelStud Finder

Phillips Screwdriver

This TV mount must be securely attached to the vertical wall. If the mounta

is not properly installed it may fall, resulting in possible injury and/or

damage. Do not exceed maximum listed weight capacity. serious injury or

property damage may occur!

Adjustable Tilt/Flat Panel Wall Mount

Do not use this product for any purpose or in any configuration not explicitly specified in these instructions. We hereby

incorrect use of this product.

disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting or any

Step 1 Mounting the Wall Plate to the Wall

Diagram 1-A Diagram 1-B

Supplied Parts List

-a (1) left TV Rail-b (1) Right TV Rail-c

(4) M5x14mm Screw-d (4) M6x14mm Screw-e (4) M8x20mm Screw-f (4) M6x30mm Screw-g

(4) M8x30mm Screw-h (4) Washer-i

(6) D8 Washer-n

(8) small spacer-j (4) big spacer-k

（6）8mm Lag Bolt-l (6) Concrete Anchor - m

Brick, Solid Concrete and Concrete Block Mounting:

Use the Wall Plate (part a) as a template to mark 6 hole locations on the wall. Three in the top row of slots and three more in the

bottom row. Make sure these holes are level and there is at least 8” distance between any two holes. Pre-Drill these holes with a

10mm masonry bit to at least 90mm in depth. Insert a Concrete Anchor (part f) into each of these holes. Make sure the anchor is

seated completely flush with the concrete surface even if there is a layer of drywall or the other material in front. Attach the Wall Plate

to the wall using 6 Lag Bolts (part e) and 6 Lag Bolt Washers (part d), as shown in Diagram 1-B.

Wood Stud mounting:

The Wall Plate (part a) MUST be mounted to two wood studs. Use a stud finder to locate two adjacent studs. It is a good idea to verify

where the studs are located with an awl or thin nail as shown in Diagram 1-A. Pre-drill a 80mm deep hole at the desired height in each

stud using a 6mm drill bit. Make sure these holes are in the center of the studs and level with each other. Use the Wall Plate as a

template to mark the location of the second hole in each stud. Drill pilot holes at each of the marked locations. Attach the Wall Plate to

the wall using the 4 Lag Bolts (part e) and 4 Lag Bolt Washers (part d).

Step 2 Mounting the TV Rails to the back of your Flat Panel TV

Make sure the TV Rails (parts b & c) are mounted at an equal distance from the top of the TV and as close to the center as possible as

shown in diagram 2-A. The safety latches on the bottom of the arms should face outward from the television and the wing nuts should

point toward the top.. M4, M5 and M8 bolts are included. If other sizes are required, they are available at your local hardware store.

Plastic Spacers (parts j & k) are provided for use with (f g h) screws. Use these spacers for televisions with curved or recessed back

panels as shown in diagram 2-C. For flat back panels, no spacers are necessary as shown in diagram 2-B. Make sure you are using

the correct bolt size for your television.Some televisions have shallow threaded inserts. 4 extra spacers have been included to

offset shallow mounting holes if the bolts provided are too long. Never force a bolt in deeper than the mountingholes allow.Doing

so may damage your television. At the same time, make sure that the bolt tip is sunk deep enough into each hole to support the

television. Before hanging the television, tighten the wing nuts on both TV rails so that the mechanism does not move during

installation.

Step 3 Hang the TV onto the Wall Plate

Warning: Some TVs may require two people to lift! Monoprice is not responsible for personal injury or product damage.

First hook the Monitor Bracket (parts b & c) over the top of the wall plate (part a). Then, let the bottom of the monitor brackets rotated

to the bottom of the wall plate as shown in Diagram 3-A. Slide up the safety latches on the bottom of each rail so that it engages the

bottom lip of the wall plate and tighten the safety screws to lock the latch in place. Finally, loosen the wing nuts on the top of each rail

to freely adjust the tilt angle of your television. Once the desired position is determined, tighten the wing nut to hold the television in

position as shown in diagram 3-B.

Level with Top

Close to centered

2-A

or or

f/g/h

d/e/f

g/h

2-B 2-C

Wall

3-A

c3-B

Loosen wind

nuts on TV

Rails

Wall

Congratulations! You’re Finished.

Thanks for Choosing. Enjoy!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monoprice Rack & Stand Handbücher

Monoprice

Monoprice 16355 Bedienungsanleitung

Monoprice

Monoprice 13815 Bedienungsanleitung

Monoprice

Monoprice 34303 Bedienungsanleitung

Monoprice

Monoprice 9744 Bedienungsanleitung

Monoprice

Monoprice MHA-800 Bedienungsanleitung

Monoprice

Monoprice MLB-108B Bedienungsanleitung

Monoprice

Monoprice 34540 Bedienungsanleitung

Monoprice

Monoprice 34542 Bedienungsanleitung

Monoprice

Monoprice 21648 Bedienungsanleitung

Monoprice

Monoprice 34539 Bedienungsanleitung

Monoprice

Monoprice 27773 Bedienungsanleitung

Monoprice

Monoprice 9744 Bedienungsanleitung

Monoprice

Monoprice Commercial Series Bedienungsanleitung

Monoprice

Monoprice MLB-110B Bedienungsanleitung

Monoprice

Monoprice 44896 Bedienungsanleitung

Monoprice

Monoprice 39305 Bedienungsanleitung

Monoprice

Monoprice 16102 Bedienungsanleitung

Monoprice

Monoprice 5754 Bedienungsanleitung

Monoprice

Monoprice WorkStream 36083 Bedienungsanleitung

Monoprice

Monoprice 39497 Bedienungsanleitung

Monoprice

Monoprice 13816 Bedienungsanleitung

Monoprice

Monoprice 24588 Bedienungsanleitung

Monoprice

Monoprice 11410 Bedienungsanleitung

Monoprice

Monoprice PID 3874 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung