Monoprice 13259 Bedienungsanleitung

–

SAFETY WARNINGS AND GUIDELINES

This speaker system is intended for indoor use only.

Do not expose these speakers to water or moisture of any kind. Do not place

drinks or other containers with moisture on or near them. If moisture does get in

or on the speakers, immediately unplug them from the power source and allow

them to fully dry before reapplying power.

If operating these speakers in a humid environment, ensure that no condensation

occurs. Condensation could cause damage to the speaker cone and could cause

a short in the amplifier, which in turn could cause fire or severe electric shock.

Do not expose this device to excessively high temperatures. Do not place it in,

on, or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it

in direct sunlight.

Use only in a well-ventilated area. Do not use in close, confined spaces. Ensure

that there is at least 12 inches of space around the main speaker to allow for

adequate ventilation.

Unplug the speakers from the power source if they will go unused for a long

period of time.

Prior to operation, check the unit and power cord for physical damage. Do not

use if physical damage has occurred.

The power supply for these speakers accepts a wide range of input voltages,

from 100 to 240 VAC, 50 or 60 Hz. Ensure that your power source is within these

limits. If not, consult a professional electrician or your power company for a

resolution.

Do not allow the power cord to be crimped, pinched, stepped on, etc. Ensure that

the power cord does not present a tripping hazard.

These speakers have no user serviceable parts. Do not attempt to open, service,

or modify them.

Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or

detergents. For stubborn deposits, moisten the cloth with warm water.

Do not subject the speakers to extreme force, shock, or fluctuations in

temperature or humidity.

Remove the battery if the remote control will go unused for a long period of time.

The remote control for this device contains a Lithium battery. Dispose of the

battery only in accordance with local, state, or federal regulations for electronic

waste.

INTRODUCTION

Thank you for purchasing this Bluetooth Bookshelf Speaker System!

This powered speaker system features a Bluetooth radio for streaming from mobile

devices, as well as a pair of stereo auxiliary inputs with RCA connectors. It includes a

high-quality Digital-to-Analog Converter (DAC), which allows you to connect it to a

computer as a USB audio device. Each of the four drivers is powered by a dedicated

50-watt (RMS) power amplifier, ensuring that each driver gets all the power it needs. A

wireless infrared remote control is included.

FEATURES

Built-in Digital-to-Analog Converter (DAC) for use as a USB audio device

Built-in Bluetooth v3.0 radio for streaming from mobile devices

Two sets of line level stereo AUX inputs

Separate 50 watt (RMS) power amplifier for each driver (200 watts total)

Includes infrared remote control

Adjustable bass and treble controls with ±6dB range

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your

ordering, purchasing, and delivery experience is second to none. If you have any

problem with your order, please give us an opportunity to make it right. You can contact

a Monoprice Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun:

9am-6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service

for a replacement.

1x Main (left) speaker

1x Slave (right) speaker

1x AC power adapter

1x Infrared remote control with installed CR2025 battery

1x Slave speaker cable

1x Stereo RCA cable

1x USB 2.0 cable

1x User's Manual

PRODUCT OVERVIEW

Speakers (Front)

1. Main (Left) Speaker: The main

speaker contains the amplifiers and

Bluetooth radio.

2. Slave (Right) Speaker: The slave

speaker is powered and controlled by

the main speaker.

3. Tweeters: One per speaker.

4. Woofers: One per speaker.

5. Status LED: The LED illuminates in various colors to indicate the selected input

and operating mode:

Solid Blue: Bluetooth input selected and actively connected to a device

Blinking Blue: The system is in Bluetooth pairing mode

Solid Green: PC mode (USB) input selected

Solid Magenta: AUX 1 input selected

Solid Yellow: AUX 2 input selected

6. Remote Control Infrared Receiver: Aim the included infrared remote control at

the main (left) speaker.

Speakers (Rear)

7. Slave (Right) Speaker Input: Plug the

included slave speaker cable into this

input on the slave (right) speaker.

8. STANDBY (Power) Button: Press this

button to power the system ON or OFF.

9. AUX-IN 1 Left/Right RCA Input Jacks

(strong signal): Connect a line level

audio source device to these RCA inputs

using the included stereo RCA cable. This

is a low sensitivity input and is intended

for use with modern audio equipment with

2000mV maximum signal strength, such

as CD players and DVD players.

10.AUX-IN 2 Left/Right RCA Input Jacks

(weak signal): Connect a line level audio

source device to these RCA inputs using

the included stereo RCA cable. This is a

high sensitivity input and is intended for

use with devices with an 800mV

maximum signal strength, such as the

headphone output of a mobile phone or

television set.

11.USB PC Input: Use the included USB 2.0 cable to connect to a computer to

use the speakers as a USB audio device.

12.DC 24V Power Input Jack: Plug the included AC adapter into this power jack.

13.Slave (Right) Speaker Output: Plug the included slave speaker cable into this

output on the main (left) speaker.

14.RESET Button: The Reset button is recessed below the surface of the panel, so

that it cannot be accidentally activated. Use a paper clip, toothpick, or other

small, blunt object to press the recessed button. If the system "locks up" or is

otherwise unresponsive, press the Reset button to restore it to the factory default

settings.

Remote Control

1. Infrared Transmitter: Aim the included infrared remote control at the main (left)

speaker.

2. MUTE Button: Press the Mute button to toggle the mute function on/off.

3. Play/Pause ( ) Button: When using the Bluetooth input, press this button to

pause or resume playback.

4. Previous ( ) and Next ( ) Buttons: When

using the Bluetooth input, press the button to

skip back to the beginning of the current track. If

already at the beginning of the track, press to

skip back to the beginning of the previous track.

Press the button to skip forward to the beginning

of the next track.

5. TRE+ and TRE- Buttons: Use these buttons to

adjust the high frequency response. Press the TRE+

button to increase the high frequency response and

the TRE- button to decrease the high frequency

response. The high frequency response can be

adjusted up to ±6dB.

6. AUX 2 Button: Press the AUX 2 button to select the

AUX 2 input. Due to the different sensitivities of the

various inputs, the volume should be decreased to

minimum or the mute function toggled on before

switching inputs. The status LED glows yellow.

7. BT Button: Press the BT button to select the Bluetooth radio input. Due to the

different sensitivities of the various inputs, the volume should be decreased to

minimum or the mute function toggled on before switching inputs. The status

LED glows blue.

8. STANDBY Button: Press the Standby button to power the system ON or OFF.

9. VOL+ and VOL- Buttons: Use these buttons to adjust the output volume level of

the speaker system.

10.BASS+ and BASS- Buttons: Use these buttons to adjust the low frequency

response. Press the BASS+ button to increase the low frequency response and

the BASS-button to decrease the low frequency response. The low frequency

response can be adjusted up to ±6dB.

11.AUX 1 Button: Press the AUX 1 button to select the AUX 1 input. Due to the

different sensitivities of the various inputs, the volume should be decreased to

minimum or the mute function toggled on before switching inputs. The status

LED glows magenta.

12.PC Button: Press the PC button to select the USB input. Due to the different

sensitivities of the various inputs, the volume should be decreased to minimum or

the mute function toggled on before switching inputs. The status LED glows

green.

13.NORMAL Button: Press the Normal button to reset any adjustments made to

the bass and treble (low and high frequency response) settings.

14.Battery Compartment (underside): The battery compartment is on the

underside at the base of the remote control.

REMOTE CONTROL BATTERY

The included remote control ships with a CR2025 Lithium battery pre-installed in the

battery compartment. A plastic film is used to prevent contact, so that the battery is not

drained during storage and shipping.

Prior to first use, grasp the plastic tab protruding from the battery compartment and pull

it out to remove the protective film, allowing the remote control to operate.

When the remaining battery capacity is low, the remote control becomes unresponsive

or responds intermittently. Perform the following steps to replace the battery:

1. Pull the battery compartment cover to remove it.

2. Replace the existing CR2025 battery with a new one. Pay close attention to the

polarity markings to ensure that it is inserted properly.

3. Push the battery compartment cover to close it.

CONNECTION DIAGRAM

The following diagram illustrates a typical configuration.

Notes:

The AUX 1 input is a low sensitivity input intended for use with devices with a

2000mV maximum signal strength, such as a CD or DVD player.

The AUX 2 input is a high sensitivity input intended for use with devices with an

800mV maximum signal strength, such as the headphone output of a mobile

phone or television set.

USB AUDIO

This speaker system features a built-in DAC and a USB input, allowing you to use it as

a USB audio device connected to a computer. Perform the following steps to configure

Windows for use with this speaker system:

1. Press the Standby button on the rear panel or on the remote control to power the

speaker system on.

2. Power on your computer and log in.

3. Using the included USB 2.0 cable, plug the USB B end into the USB PC port

on the rear panel of the main speaker.

4. Plug the USB A end into an available USB port on your computer.

5. Press the PC button on the remote control to select the USB input. The status

LED on the main speaker will illuminate green.

6. Newer versions of Windows will automatically detect the speaker system and will

set it as the default output speaker. If it does not, perform the following steps,

depending on your version of Windows.

Windows XP

a. Open Windows Control Panel.

b. Double-click the Sounds, Speech, and Audio Devices icon.

c. Double-click the Sounds and Audio Devices icon.

d. Select the Audio tab.

e. In the Sound Playback section, use the drop down list box to select the MP

Bookshelf entry for the Default device.

f. Click the OK button to save your changes.

Windows Vista and Windows 7

a. Open Windows Control Panel.

b. Click the Hardware and Sound entry.

c. Click the Sound entry.

d. Locate and double-click the MP Bookshelf entry from the list of displayed

devices.

e. Click the Set Default button to make the highlighted audio playback device the

default. A white check mark on a green background indicates the default audio

device.

f. Click the OK button to save your changes.

BLUETOOTH PAIRING

This speaker system contains a Bluetooth radio, allowing you to stream audio from your

mobile device. Perform the following steps to pair your device with the speaker system:

1. Power the speaker system ON by pressing the STANDBY button on the rear of

the main speaker or on the remote control.

2. Press the BT button on the remote control to select the Bluetooth input. The

system will automatically go into Bluetooth pairing mode. The status LED on the

main speaker will begin to blink.

3. Open the Bluetooth settings on your mobile device and initiate a search for

nearby Bluetooth devices.

4. From the list of discovered devices, select the MP Bookshelf entry. If prompted

for a passcode, input 0000 (four zeroes).

5. Once the connection is established, the status LED will cease flashing and will

change to solid blue.

Notes:

If the speaker system is already paired with an active device, pressing the BT

button in step 2 will cause the system to automatically reconnect with the

previously paired device.

To delete an existing pairing, press and hold the BT button on the remote for

about 3 seconds.

TECHNICAL SUPPORT

Monoprice is pleased to provide free, live, online technical support to assist you with

any questions you may have about installation, setup, troubleshooting, or product

recommendations. If you ever need assistance with your new product, please come

online to talk to one of our friendly and knowledgeable Tech Support Associates.

Technical support is available through the online chat button on our website

www.monoprice.com during regular business hours, 7 days a week. You can also get

assistance through email by sending a message to [email protected]

SPECIFICATIONS

Frequency Response

30Hz ~ 20kHz

Crossover Frequency

3.15kHz

SPL (1W@1m)

87dB ±3dB

THD (@1kHz)

0.25%

Signal-to-Noise Ratio

62dB (A-weighted)

Low Frequency Amplifiers

2x 50W (RMS)

High Frequency Amplifiers

2x 50W (RMS)

Treble Adjustment Range

±6dB

Bass Adjustment Range

±6dB

AUX1 Nominal Input Strength

2000mV (RMS)

AUX2 Nominal Input Strength

800mV (RMS)

Bluetooth Version

v3.0

Supported Bluetooth Profiles

A2DP, AVRCP

Built-in DAC

44.1 ~ 96 kHz DAC

Remote Control Battery Type

CR2025 3V Lithium battery

Main (Left) Speaker Dimensions

11.8" x 11.4" x 7.9" (300 x 290 x 200 mm)

Slave (Right) Speaker Dimensions

11.8" x 10.2" x 7.9" (300 x 260 x 200 mm)

Weight (Total)

28.5 lbs. (12.9 kg)

Inhaltsverzeichnis

Andere Monoprice Sprecher Handbücher

Monoprice

Monoprice PID 11427 Bedienungsanleitung

Monoprice

Monoprice Soundstage 3 Bedienungsanleitung

Monoprice

Monoprice SB-200 Bedienungsanleitung

Monoprice

Monoprice PID11180 Bedienungsanleitung

Monoprice

Monoprice Harmony Capsule 300 Bedienungsanleitung

Monoprice

Monoprice 13706 Bedienungsanleitung

Monoprice

Monoprice 14890 Bedienungsanleitung

Monoprice

Monoprice Harmony XL Bedienungsanleitung

Monoprice

Monoprice 24431 Bedienungsanleitung

Monoprice

Monoprice MS-03 Bedienungsanleitung

Monoprice

Monoprice NB-BT Bedienungsanleitung

Monoprice

Monoprice Pro Audio Series Bedienungsanleitung

Monoprice

Monoprice 34576 Bedienungsanleitung

Monoprice

Monoprice Soundstage 3 Bedienungsanleitung

Monoprice

Monoprice 43247 Bedienungsanleitung

Monoprice

Monoprice 18586 Bedienungsanleitung

Monoprice

Monoprice Pro Audio Series Bedienungsanleitung

Monoprice

Monoprice 13193 Bedienungsanleitung

Monoprice

Monoprice 43249 Bedienungsanleitung

Monoprice

Monoprice 44884 Bedienungsanleitung

Monoprice

Monoprice 605650 Bedienungsanleitung

Monoprice

Monoprice 16220 Bedienungsanleitung

Monoprice

Monoprice 13264 Bedienungsanleitung

Monoprice

Monoprice 36377 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung