Monoprice 14890 Bedienungsanleitung

SAFETY WARNINGS AND GUIDELINES

Turn off and unplug all equipment prior to making electrical connections, including

speaker wire connections.

Reduce the volume level prior to making any change to the audio input source, e.g.,

changing radio stations or changing CDs.

When using this speaker as part of a constant voltage speaker system, ensure that

the amplifier power is at least 20% higher than the total power settings of the

connected speakers.

Most speaker damage is caused by clipping, which is heard as distortion. If you hear

distortion, reduce the volume level until the audio is no longer distorted.

Take care to ensure that the speaker wire connections are properly polarized.

Inverted polarization can result in unnatural or attenuated sound, especially in the

bass frequencies.

Do not use chemical cleaners or solvents to clean this speaker. Use only a soft, dry

cloth. Moisten the cloth with warm water for particularly stubborn deposits.

The speaker has a steel safety wire with a loop running through the wire bundle.

Ensure that the safety wire is securely attached to a truss or beam inside the ceiling,

which is capable of supporting the weight of the speaker.

INTRODUCTION

Thank you for purchasing this Pendant Speaker!

This public address speaker is designed to be suspended from a ceiling in a manner similar

to a suspended light fixture. It features a built-in step-down transformer with three taps,

allowing it to be used as part of a 70V or 100V constant voltage speaker array.

FEATURES

Built-in step-down transformer with three taps for use in a 70V or 100V constant

voltage speaker array

6-inch main driver

150Hz ~ 14kHz frequency response

92dB sound pressure level

Steel safety wire supports the weight of the speaker

PACKAGE CONTENTS

1x Pendant speaker

1x User's manual

CONSTANT VOLTAGE VS 8-OHM SPEAKER SYSTEMS

A constant voltage speaker system differs from a traditional 8-ohm speaker system in that

it uses a step-up transformer at the audio source to raise the voltage and lower the current

on the transmission line. At the speaker end, a step-down transformer converts the signal

back to a normal speaker level voltage. This reduces power loss during transmission, which

allows for the use of longer speaker wire runs using smaller gauge wire.

Additionally, a constant voltage speaker system allows for the use of multiple speakers on

each channel, without the need for complicated impedance calculations and

configurations. In a constant voltage system, all speakers on a given channel are connected

in parallel and the complicated impedance calculations are replaced by simple wattage

calculations.

For example, if you want to connect two speakers per channel in a traditional 8-ohm

speaker system, you must either connect them in series, which results in an overall 16-ohm

impedance, or in parallel, which results in an overall 4-ohm impedance. In the first case, the

16-ohms impedance effectively halves the output power of your amplifier, resulting in

lower overall volume levels. In the latter case, the 4-ohms impedance means that your

amplifier will have to work harder and must be rated as stable at 4 ohms. Adding a third

speaker to the mix would complicate it further, producing either a 24-ohm or 2.67-ohm

overall impedance. Note that very few amplifiers are stable under 2-ohm loads, so that is

usually not an option.

On the other hand, with a constant voltage system, you consider first the RMS output

wattage of the amplifier. This should be reduced by 20% to compensate for insertion loss.

For example, if using a 100-watt amplifier, the total load from speakers should not exceed

80 watts.

Each individual speaker on a given channel is set to a value such that the total does not

exceed the rated power, less 20%. You do not need to worry about making the total as

close as possible to the limit; just ensure that the total does not exceed the limit.

If all speakers are set to the same wattage value, they will all have the same volume level.

If one speaker is set to a higher wattage value, it will be louder than the others, while a

speaker set to a smaller value will be quieter than the others. This allows you to

compensate for the environment in which the speaker is placed. For example, a speaker

placed outside would need to be louder than a speaker placed in a small room.

SPEAKER WIRING

Most constant voltage speaker installations will consist of

multiple speakers per channel, with all speakers connected in

parallel, as shown in the diagram to the right.

To wire speakers in parallel, connect the first speaker to the

amplifier as normal. Connect the positive terminal on the first

speaker to the positive terminal of the second speaker, and

the negative terminal on the first speaker to the negative

terminal on the second. Repeat for each additional speaker in

the array

INSTALLATION

Perform the following steps to install this speaker.

1. Determine the desired mounting location for the speaker.

2. Using a 1/4" drill bit, drill a hole through the ceiling for the speaker/safety wire cable

bundle to pass through.

3. Feed the cable through the hole in the ceiling.

4. While supporting the speaker at the desired height, take out the slack from the

cable within the ceiling and secure the safety wire to a beam, truss, or other solid

support.

5. Multiply the rated RMS power output of your amplifier by 0.8 to determine the

maximum total wattage for the speaker array.

Example: If you are using the 14886 120-watt PA amplifier, the maximum wattage of

the connected speaker array is 120 x 0.8 = 96 watts.

6. Determine which transformer tap to use on this speaker. The following table

indicates the wattage values for each of the three taps in 70V and 100V systems.

Transformer Taps

Green

Yellow

Red

70V Array

1.85 watts

3.75 watts

7.5 watts

100V Array

3.75 watts

7.5 watts

15 watts

7. Run speaker wire from the amplifier to the speaker installation location.

Important Safety Warning! You must use in-wall rated speaker wire for residential

installations or plenum rated speaker wire for commercial installations.

8. Connect the positive lead of the speaker wire to the Green, Yellow, or Red lead on

the speaker, then connect the negative lead to the Blue lead on the speaker. Use

electrician's tape, wire nuts, or heat shrink tubing to protect and isolate the

electrical connections. Similarly, the unused taps should be have their exposed

conductors taped or otherwise protected from accidental contact.

9. Connect the speaker wire to the speaker output terminals on the amplifier, taking

care to maintain proper polarity.

Congratulations, your pendant PA speaker is installed and ready for use!

TROUBLESHOOTING

Q1: The sound from one of the speakers is muddy, with attenuated bass response.

A1: Double check the polarity of the speaker wire connections.

Q2: The sound from one of the speakers is louder or quieter than the other speakers in a

constant voltage system.

A2: Check the wattage settings of the affected speaker. If it is higher than that of the

other speakers, it will be louder. Similarly, if it is set to a lower value, it will be quieter

than the other speakers. To get the same volume level, set the switch to the same

wattage setting as is used on the other speakers.

Q3: The sound from all the speakers is scratchy, harsh, or fuzzy sounding.

A3: You are hearing audible distortion, which can cause damage to both the speakers and

the amplifier. Reduce the volume level until distortion can no longer be heard in any

part of the audio signal.

SPECIFICATIONS

Model

14890

Woofer Size

6-inches

Input

70V or 100V

70V Power Taps

1.85, 3.75, or 7.5 watts

100V Power Taps

3.75, 7.5, or 15 watts

Transformer Impedance

2.6k, 1.3k, or 670 ohms

Frequency Response

150Hz ~ 14kHz

SPL (1 watt@1 meter)

92dB

Safety Wire Length

About 50"

Dimensions

ø6.8" x 9.8" (ø172 x 250 mm)

Weight

5.7 lbs. (2.6kg)

REGULATORY COMPLIANCE

Notice for FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired

operation.

Modifying the equipment without authorization may result in the equipment no longer

complying with FCC requirements for Class B digital devices. In that event, your right to

use the equipment may be limited by FCC regulations, and you may be required to correct

any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Notice for Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Inhaltsverzeichnis

Andere Monoprice Sprecher Handbücher

Monoprice

Monoprice 34576 Bedienungsanleitung

Monoprice

Monoprice Pro Audio Series Bedienungsanleitung

Monoprice

Monoprice Soundstage 3 Bedienungsanleitung

Monoprice

Monoprice 14889 Bedienungsanleitung

Monoprice

Monoprice MP True Bedienungsanleitung

Monoprice

Monoprice Pro Audio Series Bedienungsanleitung

Monoprice

Monoprice 13706 Bedienungsanleitung

Monoprice

Monoprice PID11180 Bedienungsanleitung

Monoprice

Monoprice SB-200 Bedienungsanleitung

Monoprice

Monoprice NB-BT Bedienungsanleitung

Monoprice

Monoprice 36379 Bedienungsanleitung

Monoprice

Monoprice PID 11427 Bedienungsanleitung

Monoprice

Monoprice 10951 Bedienungsanleitung

Monoprice

Monoprice DT-4BT Bedienungsanleitung

Monoprice

Monoprice SSVC-6.1 Bedienungsanleitung

Monoprice

Monoprice 13264 Bedienungsanleitung

Monoprice

Monoprice MM-5 Bedienungsanleitung

Monoprice

Monoprice 14446 Bedienungsanleitung

Monoprice

Monoprice 43247 Bedienungsanleitung

Monoprice

Monoprice 10920 Bedienungsanleitung

Monoprice

Monoprice 10800 Bedienungsanleitung

Monoprice

Monoprice Harmony XL Bedienungsanleitung

Monoprice

Monoprice 33828 Bedienungsanleitung

Monoprice

Monoprice 44884 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung