Monte Carlo Fan Company 3IKR44 Series Gebrauchsanweisung

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3IKR44XXXD Series Fan

CUL Model NO. : 3IKR44XXD

6.25 kg

13.75 lbs

Owner’s Guide and Installation Manual

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing, servicing or cleaning the fan unit, switch the power off at the service panel and lock the service panel to prevent

the power from being switched back on accidentally. If the service panel cannot be locked to prevent the power from being switched on accidentally,

securely fasten a warning sign to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To reduce the risk of ﬁre, electric shock, or personal injury, mount to outlet box marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or

less” and use mounting screws provided with the outlet box.

CAUTION: Comply with local codes and regulations. If installing the secondary support safety cable in the U.S., do not remove knockouts in the outlet

box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure or the ceiling joist.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. MR181A-3 manufactured by Satellite

Electronic (Zhongshan) Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, FOLLOW THESE INSTRUCTIONS.

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble).

Remove the 2 set screws corresponding

the round holes in the canopy and loosen

the other 2 set screws. Keep the screws.

Remove the mounting plate by turning

counterclockwise.

Place the decorative ring over the

canopy.

Install the mounting bracket onto the

outlet box.

Partially loosen the two screws on the

outlet box, attach the mounting bracket

onto the outlet box by sliding it over the

two screws as shown in the illustration.

Outlet box

Mounting plate

Motor assembly

Mounting plate

Decorative ring

Motor assembly

7 8 9

10 11

Have the mounting bracket in position

and tighten the set screws.

To prepare the fan for wiring, hang fan

onto mounting bracket by sliding the

canopy over the mounting bracket hook

(Use one of non-slotted holes on the

rim of the canopy).

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 3” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

Make wiring connections using wire connectors provided as indicated above. White from

fan to White from remote marked to motor N. Black from fan to Black from remote marked

to motor L. Blue from fan to Blue from remote marked FOR LIGHT. White (Neutral) from

house to White from remote marked AC IN N. Black (Live) from house to Black from

remote marked AC IN L. Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Fix the receiver with the clip on the mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded

conductor and the equipment-grounding conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet box. The splices after being

made should be turned upward and pushed carefully up into the outlet box.

Caution: The installation has to be complete before operate the fan.

Lift fan to mounting bracket, aligning the

“L” shape holes on canopy with the

screws on the mounting bracket. Turn the

fan clockwise to lock in position. Install

the other 2 canopy mounting set screws

that are removed in the installation step 4

and tighten all screws securely.

Install decorative ring. Align the head of

set screws on the canopy with the groove

in the decorative ring and twist clockwise

till tight.

Lag screw

Safety cable

Washer

Lock washer

Wall switch White

White

Black

Blue

Power source

Green/Ground

Receiver

SAFETY CABLE INSTALLATION

Hook

12 13 14

1615

Insert blade into the slot on the ﬂywheel.

Install blade by the screws and washers

provided, aligning each of the holes as

shown and tighten all screws securely.

Repeat this process for remaining blades.

Place the lead wires from fan over the

central hole of light pan.

Aligning the keyhole slots on the light pan

with the preassembled screws on the

plate. Twist clockwise till lock. Reinstall

the screw which was just removed.

Tighten all screws securely.

Loosen 2 and remove 1 preassembled

screws from light pan. Keep screw.

Attach glass by locating dimples in light

pan with grooves on the glass and twist

clockwise until tight.

Connect white wire from fan to white wire

from LED light ﬁxture and then connect

blue (or black) wire from fan to black (or

blue) wire from LED light ﬁxture. Be sure

plugs connection clasped together ﬁrmly.

Attach LED light ﬁxture onto the light pan,

aligning the keyhole slots on the LED light

ﬁxture with the preassembled screws on

the light pan. Twist clockwise till lock.

Reinstall the screw which was just

removed. Tighten all screws securely.

This light kit includes 2700 (Warm white),

3000 (Soft white) and 4000K (Daylight)

correlated color temperatures (CCT). Get

desired CCT by operating the converted

switch.

Attach light shade by locating dimples in

light pan with grooves on the light shade

and twist clockwise until tight.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Blade

Washer

Set screw Light pan

Light shade

Flywheel

Plate on motor

Color temperature

converted switch

light ﬁxture

Setting the reverse switch in the left hand

side will result in downward airﬂow and

setting the switch in the right hand side

will result in upward airﬂow.

Note: Reverse switch must be set either

way completely. If the reverse switch is

set in the middle position, fan will not

operate.

Reverse switch

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install batteries.

Replace the cover. This remote uses 2 1.5V/AAA batteries.

Note: If not using for long periods of time, remove the batteries to prevent damage to

remote controller, and store the remote controller away from excess heat or humidity.

The batteries will weaken with age and should be replaced before they leak or corrode as

this will damage the controller. Dispose of the used batteries properly. Always keep

batteries out of the reach of children.

Dimming, Non Dimming Setting (Only available for fans with light)

In the dimming mold, it is a light dimming selection and it is to be used with dimmable

luminaries. The remote controller is set with dimming function at factory.

In ON/OFF (non-dimming mold), it is for light ON/OFF only (non-dimming function).

The remote control buttons control the fan speed as follows:

1 = low speed 2 = medium speed 3 = medium high speed

4 = high speed

This button turns the fan off.

Light button- Press this button to turn light on or off.

Light button- Press this button to desired brightness, dim to bright.

Light button- Press this button to desired brightness, bright to dim.

Breeze-

Press the Breeze button, the Fan will operate randomly among 1st - 4th speed until the breeze mode is

canceled.

Breeze mode can be erased by pressing either the power or speed control buttons.

Note

: This remote controller has auto resume function, the fan and light will maintain the last setting if

turned off with exception of the Breeze mold.

Battery cover

DIM (D)

ON/OFF (O)

SET

Universal Mode and Learning Mode

Your remote controller has two options: “Universal Mode” (mark “0”) and “Learning Mode” (mark “1”).

If choosing “Universal Mode,” simply move the switch to the LOWER position (mark “0”). Your fan with

the remote controller is ready to use.

Note: If using Universal Mode, your fan can be controlled with other remote controllers with the same

setting.

To control the fan with a speciﬁc remote controller, choose “Learning Mode” by moving the switch to

the UPPER position (mark “1”) and then follow the Learn Mode steps below.

Learn Mode

Important: Turn the power on for ONLY the speciﬁc fan you wish to pair with the remote controller.

Make sure to turn the power off for all other fans with which you use the same remote controller.

Restore power to your fan, press and hold the “SET” button to pair the transmitter and receiver. You

must press the ‘SET” button within 60 seconds of restoring power to the fan.

Note

: Fan will at ﬁrst operate at minimum speed and light will blink (if your fan has a light) after you’ve

chosen Learn Mode.

Note

: If the power is already on, you must turn the power off and then back on for the remote control

setting.

Note

: If you reset the controller to Universal Mode (mark “0”) and later want to pair the controller

again to a speciﬁc fan, you have to repeat the Learn Mode steps.

Wall mount cradle

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS. (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

User Tips

1. If your fan is operating automatically after installation, it is still using the factory setting. Follow the settings for Learn Mode

above to reset.

2. If the fan or light isn’t working, reset power (turn the power off then turn the power back on) and follow the Universal Mode or

Learn Mode remote control settings.

3. If two or more fans in the same remote signal range are on the same power supply, they cannot be operated separately by

remote control. Use a separate power supply for each fan, such as an individual wall switch, and restrict the power supply to

only the fan which you are pairing with its transmitter in order to use the remote controller.

Install Transmitter wall mount cradle with 2 screws provided.

Useful tips:

The remote transmitter can be removed by pressing it

upward from the lower half.

The remote transmitter can be held on magnetic metal

materials by a magnet built in the transmitter.

Troubleshooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

and lock the service panel to prevent the power from being switched back on accidentally. If the service panel

cannot be locked to prevent the power from being switched on accidentally, securely fasten a warning sign to the

service panel.

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

1. Check to make sure all screws in motor housing are snug (not over tightened).

2. Check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4. Check to be sure lightbulb is tight in socket and not touching the glass shade.

5. Some fan motors are sensitive to signals from Solid State variable speed controls.

6. Allow "break-in" period of 24 hours. Most noises associated with a new fan will

disappear after this period.

1. If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2. Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4. Check that all blade holders are tightened securely to motor.

5. Most fan wobble problems are caused when blade levels are unequal. Check this level

by selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceiling. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6. If blade wobble is still noticeable, interchanging two adjacent blades can redistribute the

weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamically

balance your fan with balancing kit provided.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty lightbulb and make sure bulb is tight in socket.

5. Remove light kit and check the plug connections if they are present.

6. If this fan uses a remote controller, make sure dip switches are in the correct setting

and make sure the battery works.

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Nov.2021

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5CQM44RZW Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4AAR13XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLCR54XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 6LFR62 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AKR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VTR52D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WS52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR52XX Fan Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3DLR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLNSM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ALR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VLR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Orbis 3OBSR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AXR52XX3-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CZ52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4GIR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54XX Technisches Dokument

Monte Carlo Fan Company

Monte Carlo Fan Company 5HM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VYR56XXD Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung