Monte Carlo Fan Company 3LRR66 Service-Handbuch

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proo o purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your ixture, please visit our website www.montecarlo ans.com

3LRRXXD Series Fan

Total an weight with light kit

UL Model No. : 3LRR66/52

10.6 kgs

23.4 lbs

Shown with 66”

blades

Shown with 52” blades

Energy Star approved with

52” blades

WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G

READ A D SAVE THESE I STRUCTIO S

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RYK manufac-

tured by Rhine Electronic Co., Ltd.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

ever place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Cutomer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlo ans.com

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting

means to prevent power from being switched on ac-

cidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warn-

ing device, such as a tag, to the service panel.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per-

sonal injury, mount to outlet box or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Remove cotter pin from downrod, and

save for later use.

Place canopy over downrod.

Loosen the 2 set screws until the do

not protude into the inside of the

yoke.

Use metal outlet box suitable for fan support and

use only the screws provided with the outlet

box (must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet box is securely fas-

tened by at least two points to a structural ceiling

member ( a loose box will cause the fan to wobble).

Remove the two outlet box screws provided with

the box, aligning the holes of the mounting bracket

with the holes of the outlet box. Re-install the 2

outlet box screws securely.

Place yoke cover over downrod.

Thread the leadwires and safety

cable through the downrod.

Insert downrod into the yoke on top

of fan body. Align the hole in the

downrod with the hole in the yoke.

Insert cotter pin through yoke and

downrod until point appears on the

other side

Make sure the studs protruding from the

bottom of the Mounting bracket are in-

stalled with threads all the way through

the bracket.

Tighten the 2 set screws on the yoke,

once the down rod is in place.

Hang assembled fan from the mounting bracket in-

stalled to ceiling in previous step. Make sure the fan

is hanging straight. Rotate fan until the tab on the

Mounting bracket engages the slot on the Downrod

Ball. This must be done to prevent the fan body from

rotating when the blades are in motion.

Install keeper pin.

Set dip switches on the Remote Transmitter and Remote

Receiver to the same settings. This must be done so the

units will communcate properly. If you have other fans

you can set to control from one transmitter by setting both

receivers the same as the transmitter. If you have more

than one fan with remote. You can set the dip switches to

different positiosns to have seperate control.

Remote Transmitter Dip swtiches

Remote Receiver Dip switches

Install remote receiver into the

mounting bracket.

Make wiring connections as indicated above.

White from fan to white from remote marked

N. Blue from fan to blue from remote marked

light. Black from fan to Black from remote

marked L. White from house to white from re-

mote marked AC N . Black from house to Black

from remote marked AC L. Connect all green

ground wires to Grounded wire from House.

Ready for wiring.

For Canadian installation and for USA fan and

light kit combinations over 35 lbs, in both flush

and downrod mode the safety cable must be in-

stalled into the house structure beams using the

3” lag screws,washers, and lock washers. pro-

vided. Make sure that when the safety cable is

fully extended the leadwires are longer than the

cable and no stress is placed on the leadwires.

17 Safety cable installation

Safety Cable

Lag Screw

safety

cable

3” lag

screw

lock

washer

Connect white wire from fan to White

wire from light fixture. Connect blue

wire from fan to Black wire from light

fixture.

Lift canopy and install knurled nuts as

shown. Tighten the knurled nuts securely.

The canopy should adjust for any irregu-

larity in the ceiling or utlet box.

Check for shipping stabilizers and remove

if present. Attach blades using screws in

hardware pack. Blades sold seperately.

Tighten screws securely. Repeat 2 more

times.

Loosen 2 screws are remove one screw.

Keep removed screw for later use.

Alighn keyslot holes of light kit plate and

twist to lock clockwise. Install screw re-

moved in step 22 and tighten all screws

securely.

Remove battery cover. Install 12V battery into

wall remote. Duracell MN21 / Eveready A23 / GP

23A all 12V.Attach cover of remote by placing

over buttons and snap the battery cover in place.

Place face plate over battery compartment and

buttons. Place remote over 2 pins on front cover.

Attach cover of remote by placing over 4 pins

and snapping into place. Install wall control unit to outlet box

using machine screws provided.

2726 HAND HELD INSTALL WALL M UNT INSTALL

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of the

wirenut. After making the wire connections, the wires

should be spread apart with the grounded conductor

and the equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on the other

side of the outlet box. The splices, after being made,

should be turned upward and pushed carefully up into

the outlet box.

Attach front cover to wall control with

screws provided. Snap battery cover

in place.

Attach blanking plate by locating dim-

ples in light fixture with grooves in

the blanking plate and twist clock-

wise.

For fan without

bulb, go to step

29.

For fan with

bulb, go to step

Attach the GU24 18W CFL bulb and

secure by twisting clockwise. Bulb in-

cluded.

WA NING: USE MAXIMUM GU24 18

WATTS LISTED SBCFL(SELF-BALLASTED

C MPACT FLU RESCENT LAMP) NLY, N T

USING SBCFL WILL VERHEAT THE UNIT

AND CAUSE DAMAGE T THE UNIT R THE

FAN WHICH THE UNIT IS INSTALLED T -

GETHER.

Attach the glass by locating dimples in

light fixture with groves in the glass

and twist clockwise until tight.

WA NING: This fixture is not dimmable. Use only with on/off switch.

Do not use in conjunction fan/light remote controls or light dimmers.

emote Control Transmitter Features:

FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for

high. To turn fan off press square”.

LIGHT ON/OFF To turn light on, press light button once quickly. To turn off

press once quickly while light is on.

FO WA D/ EVE SE Depress rev button allow a few seconds for remote to

change rotation direction with fan running.

HIGH SPEED

MEDIUM SPEED

LW SPEED

FAN FF SETTING

(Turns fan off only)

FAN REVERSE (Press

once to change direc-

tion of the fan) Fan

must be running to

reverse.

LIGHT N/ FF SETTING

(Press to turn on/off light)

LED LIGHT

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when

switch is in the middle.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each other or

against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State variable speed controls.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this

period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and

junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting

a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to

ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-

ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-

lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and

blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade holder at the two screws farthest from the motor. Reverse the position

of the washer if blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute

the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

WA NING: USE MAXIMUM GU24 18 WATTS LISTED SBCFL(SELF-BALLASTED COMPACT FLUO ES-

CENT LAMP) ONLY, NOT USING SBCFL WILL OVE HEAT THE UNIT AND CAUSE DAMAGE TO THE

UNIT O THE FAN WHICH THE UNIT IS INSTALLED TOGETHE .

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

User Servicing Instructions

WA NING: Before attempting to replace the fuse make sure the main power is turned off

to the fan. (Fuse is inside the canopy on the blue wire to remote receiver, push and twist

the cap to open the fuse case) Push and twist to reassemble fuse.

isk of fire. eplace fuse only with 3 amp, 125 volt fuse.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TR UBLE SH TING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Cus-

tomer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Jan.27.10 revise - Add ES logo, ES approved with 52” blades

Feb.2012 New format

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company Launceton 56 4LNCR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ROZR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AVLCR54XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ARR58XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LD52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5KBR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EXR60XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BGR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ASPR70 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VMR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DI52ES D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DH52 series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CMR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ERAR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MAR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5FNR60 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AMR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SY52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Rockland 4RKR60 D Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung