Monte Carlo Fan Company 3AMR60 D Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Total fan weight with light

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3AMR60XXXD Series Fan

cETL Model NO. : 3AMR60(X)

6.6 kgs

14.52 lbs

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA

70), including ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the ﬂoor to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the

building structure (or the ceiling joist).

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With a general use, isolating Wall Control/Switch.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. DC8 manufactured by

Carewell Electric Technology (Zhongshan) Co.,Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable

speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is

required, the product should be returned to an authorized service facility for examination or repair.

All set screws must be checked, and re-tightened where necessary, before installation.

Note: Suitable for use in damp locations.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35 lbs).

Before attaching fan to outlet box, ensure

the outlet box is securely fastened by at

least two points to a structural ceiling

member (a loose box will cause the fan to

wobble). Remove the two outlet box

screws provided with the box, aligning

the holes of the mounting bracket with

the holes of the outlet box. Reinstall the 2

outlet box screws securely.

Remove the set screws from Yoke. Keep

screws.

Remove the top housing. Insert blades (the 3 blades with a label

“This side up”) into the top slots on

ﬂywheel.

Note: Make sure the side with a label

“This side up” is installed upward.

Mounting bracket

Set screw

Yoke

Top housing

Top slot

Bottom slot

Blade

This side up

Top housing

7 8 9

10 11 12

Align the holes on blade with the screw

holes on the bracket inside fan housing

and partially install the blades with set

screws provided.

Note: The screw holes on the bracket

are not vertical, install the set screws

align with the screw holes as shown in

illustration.

Make sure to tighten the set screws

after top and bottom blades are

assembled together.

Flip the fan body with blades over and

insert the other blades (the blades with

inserted nuts) into the other slots on the

fan housing.

Note: The inserted nuts here should

be downward, face to the blades

installed in the last installation step.

Align the holes on blade with the screw

holes on the bracket inside fan housing

and install the blades with set screws

provided. Tighten the set screws

securely.

Note: The screw holes on the bracket

are not vertical, install the set screws

align with the screw holes as shown in

illustration.

Flip the fan body with blades over again.

Assembly the top and bottom blades with

set screws and washers provided.

Helpful hint: Make small adjustment by

moving the blades a little, and moving

bottom bade upward may help to align

the holes and screw holes.

Note: Make sure to tighten the set

screws of top blades with the

bracket.

Replace the top housing on the yoke.

Install it with the set screws remove in

installation step 4.

Remove preassembled keeper pin and

cross pin from downrod.

Bracket

Keeper pin

Cross pin

Downrod

Inserted nut

15~20°

13 14 15

16 17 18

Place downrod over canopy, canopy

bottom cap and yoke cover.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Thread lead wires and safety cable from

motor assembly through downrod.

Helpful hint: For easy assembling of the

cross pin on the next installation step.

After slip downrod into the motor yoke,

carefully insert a Phillips screwdriver through

the yoke and downrod (don’t damage the

lead wires) as a guide and then push the

cross pin and pull the screwdriver in the

meantime as shown in the inset.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and keeper

pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the cross

pin, and then evenly tighten the downrod set

screws on motor housing yoke.

Place Yoke cover on motor assembly.

Warning: Cross pin and keeper pin must be

installed securely, failure to install them will

result in serious injury.

For Canadian installation and for USA fan

and light kit combinations over 35 lbs, in

both ﬂush and downrod modes the safety

cable must be installed into the house

structure beams using 1.5” lag screws,

washers and lock washers provided.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper

than 20º.

Canopy

Downrod

Yoke cover

Canopy bottom

cap

Canopy

Yoke cover

Safety

cable

Yoke

Keeper pin

Cross pin

Downrod

Yoke cover

Set screws

Canopy

Canopy bottom cap

Tab

Downrod

Slot

Canopy bottom cap

Yoke

Cross

Screwdriver

Lead wire

Downrod

Set screw

Yoke

21 23

Make wiring connections using wire connectors provided as indicated above.

Red from fan to Red from remote marked Motor 1.

Purple from fan to Purple from remote marked Motor 2.

Gray from fan to Gray from remote marked Motor 3.

Blue from fan to Blue from remote marked FOR LIGHT.

White from fan to White from remote marked FOR LIGHT.

White (Neutral) from house to White from remote marked AC IN N.

Black (Live) from house to Black from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded

conductor and the equipment-grounding conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet box. The splices after being made should

be turned upward and pushed carefully up into the outlet box.

Lift canopy up, aligning its keyhole slot

with the preassembled screw on

mounting bracket and twist

counterclockwise to lock in place.

Reinstall the screw removed in step 20

and tighten all screws securely.

Attach canopy bottom cap onto canopy

by aligning its notch with the screws on

mounting bracket and twist clockwise till

tight.

Loosen 2 and remove 1 preassembled

screw from the plate on motor. Save

screw for later use.

Place light pan over the lead wires and

attach it onto the plate on motor, aligning

the keyhole slots on the light pan with the

preassembled screws on the plate. Twist

clockwise till lock.

Partially loosen one and remove one

preassembled screw from mounting

bracket. Save screw.

Blue (For Light)

White (For Light)

Red (Motor 1)

Purple (Motor 2)

Gray (Motor 3)

Black (AC IN L)

White (AC IN N)

Green/Ground

Wall Switch

Ground/Green

Black (Live)

White (Neutral)

Power source

Receiver

Plate on motor Light pan

24 25

27 28

Reinstall the screw removed in step 22.

Tighten all screws securely.

Connect white wire from fan to white wire

from LED light ﬁxture and then connect

black (or blue) wire from fan to blue (or

black) wire from LED light kit.

Note: If you don’t want to install the fan

with LED light, go to step 29 for blanking

plate installation.

Remove 3 preassembled screw from the

light pan. Save screws for later use.

Attach LED light ﬁxture onto the light pan,

aligning the holes on the LED light kit with

the screw holes on light pan. Reinstall the

screws removed in step 25. Tighten all

screws securely.

Attach lexan shade by locating dimples in

light pan with slot on the lexan shade and

twist clockwise until tight.

Attach blanking plate by locating dimples

in light pan with grooves on the blanking

plate and twist clockwise until tight.

Note: Do not install LED light kit if

use blanking plate.

Blanking plate

Light pan

Install LED Light Kit

Install Blanking Plate

LED light fixture

Lexan shade

REMOTE CONTROL SETTING and OPERATION

Universal Mode and Learning Mode

There are “Universal Mode” and “Learning Mode” with the remote controller.

If choosing “Universal Mode”, simply place dip (code) switch at UPPER

position. Your fan with the remote controller is ready to use.

Note: If using universal mode, your fan can be controlled with other remote

transmitters with the same setting.

To control the fan with speciﬁc remote transmitter, choose “Learning Mode”

by placing the dip (code) switch at LOWER position and then make learn

function setting as below.

Learn function setting, Restore power source to your fan, press and hold

the “LEARN” button for at least 3 seconds. You must press the “LEARN”

button within 60 seconds of restoring power to the fan.

Note: If the power is on already, you must turn the power off for 10 seconds

at least, and then turn the power back for remote control learn function

setting.

Note: If the fan is installed with light, light will twinkle 2 times. The remote

control setting process is complete and your fan is ready for use. For fans

without light, check operation using remote transmitter.

Note: If you want to control the fan with another transmitter, make the same

setting. A fan can be controlled by 2 transmitters maximum.

Transmitter Operation

Remove the battery cover from the remote control transmitter and install

battery, battery provided. Replace the cover.

Note: Use 2 1.5V/AAA battery.

Note: If not using for long period of time, remove battery to prevent damage

to remote transmitter, and store the remote transmitter away from excess

heat or humidity.

DIM

LEARN

L.CODE

COMMON

CODE

L.CODE

COMMON

CODE

DIM

Universal Mold

Learning Mold

Dimming / Non Dimming Setting

The “DIM” selection is the light dimmable selection and the light will cycle

from bright to dim to bright until button is released. The “ON” selection is the

light ON/OFF only (non dimming function). Light will maintain last setting if

turned off.

Note: The remote controller is set with dimming function at factory,

Note: If the remote receiver has been wired with fan, turn power off by wall

switch before switch “DIM” and “ON/OFF” selection.

Dimming/

Non dimming

LEARN

Learn

The receiver provides the following protective functions

Lock protection- The DC motor has a build-in safety feature against blade or motor obstruction during operation. If

something obstructs the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation

after about 60 seconds of interruption. Please remove obstacles and reset. To reset it by turn the fan off by remote

transmitter and then turn the fan on, Or you may turn power off for 15 seconds then turn power back, and then turn

the fan on,

Over load protection (current limit)- The device will limits the maximum current output from the receiver/drive when the

fan or light load was increased abnormally.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT

CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

The buttons on the remote control transmitter control the fan speed and light as follows.

Fan speed

1 = minimum speed 2 = low speed

3 = medium low speed 4 = medium speed

5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/Reverse button- This button is to control direction of fan rotation. Press once

to change direction of the fan rotation. Fan must be running to reverse.

Light button- Press this button to turn light on or off. To dim light (

Setting at “DIM”

position

), hold down the button, the light will cycle from bright to dim to bright until button

is released.

Note

: This remote controller has auto resume function, the fan and light (If the fan with

light) will maintain the last setting if power is turned off.

Tips for end users

1. If your fan is operated automatically after installation and power on, it is because your fan is still memorize the previous

setting at factory.

2. If fan or light isn’t working, reset power (turn the power off for at least 10 seconds and then turn the power back) and redo

the learn function setting.

3. It is not available to separately operate the learn setting for more than one fan in the same room (in the area where remote

signal can reach to) if they share the same power supply. Separate power supplies (like as using individual wall switches for each

fan and turn power off for the fan while you are making learn function for other fan) is required if you want to separately control

more than one fan in same room.

4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal

performance of this fan and it will take for few seconds to run this operation.

Install Transmitter wall mount cradle with 2 screws provided.

Wall mount cradle installation

Trouble Shooting

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,

installation, please call our Customer Service Center at the

number printed on your parts list insert sheet.

Warning

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be

locked, securely fasten a prominent warning device, such as a tag, to the service panel.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION

either way. Fan will not operate when switch is in the middle.

4.If this fan uses remote controller, make sure dip switches are setting properly and make

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION

4.Check to be sure light bulb is tight in socket and not touching the glass shade.

5.Some fan motors are sensitive to signals from Solid State variable speed controls.

6.Allow "break-in" periodof 24 hours. Most noisesassociated with a new fan will disappear

after this period.

1.If this is a downrod mount fan, make sure the ridge on mounting bracket engages the

notch in the downrod ball.

2.Make sure that canopy, mounting bracket or mounting plate are tightened securely to

4.Check that all blade holders are tightened securely to motor.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade

is positioned for measurement. Repeat for each blade. If all blade levels are not equal,

you can adjust blade levels by the following procedure. To adjust a blade tip down, insert

a washer (not supplied) between the blade and blade holder at the screw closest to the

motor. To adjust a blade tip up, insert washer (not supplied) between the blade and blade

holder at the two screws farthest from the motor. Reverse the position of the washer if

blades mount from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

If the above steps do not eliminate the wobble problem, you will need to dynamic balance

your fan with balancing kit provided.

1.Check blue wire from fan to make sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulb and make sure bulb is tight in socket.

5.Remove light kit and check the plug connections if they are present.

6.If this fan uses remote controller, make sure dip switches are setting properly and make

CAUTION: Make sure main power is turned off before entering switch housing and/or

canopy.

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. If fan does not start:

Trouble Suggested Remedy

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 5MMR54 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DS44 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GP60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR99XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ATR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Discus Trio Max 3DIR58 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DH52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PAR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5PPR54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DS52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5VSR60XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Hicks 3HCKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Rockland 4RKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CZ52XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4TSR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Melody 3MER56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCM52XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DCR60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSM60 Series Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung