Monte Carlo Fan Company 5OR52XXD Series Bedienungsanleitung

QUALITY CEILING FANS

Ceiling Fan Installation Instructions

For 5OR52XXD Series Fans

READ AND SAVE THESE INSTRUCTIONS

Total fan weight

with light kit

OWNER’S

MANUAL

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support and

use only the screws provided with the outlet box. (Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat-

ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such

as a tag, to the service panel.

10.

11.

12.

13.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

SAFETY TIPS

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally. When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Loosen the 2 set screws in yoke for

downrod to slip into yoke. Insert

downrod into yoke on top of the Fan

Body. Align the hole in the Downrod

with the hole in the Yoke. Insert the

Pin through the Yoke and Downrod

until the point appears on the other

side. Install the Keeper Pin

Tighten the 2 Set screws on the Yoke

once the downrod is in place. Check

motor for shipping stabilizers and

remove if present.

Tread leadwires and safety cable first

through the canopy disk, Canopy and last

the downrod.

4Canopy disk Downrod

Canopy

Yoke

Cross Pin

Keeper

Installation

Use metal outlet box suitable for fan support

and use only the screws provided with the out-

let box (must support 35 lbs). Before attaching

fan to outlet box, ensure the outlet box is

securely fastened by at least two points to a

structural ceiling member ( a loose box will

cause the fan to wobble). Use only the

screws provided with the outlet box.

For Canadian installation in both flush and down-

rod mode the safety cable must be installed into

the house structure beams using the 3” lag screws

provided. Make sure that when the safety cable is

fully extended the leadwires are longer than the

cable and no stress is placed on the leadwires.

Hang assembled fan from the mounting bracket

installed to ceiling in previous step. Make sure the

fan is hanging straight. Rotate fan until the tab on

the Mounting bracket engages the slot on the

Downrod Ball. This must be done to prevent the fan

body from rotating when the blades are in motion.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on

the other side of the outlet box.

CCaannaaddiiaannmmoouunnttiinnggoonnllyy

Safety Cable

Lag Screw

Make sure the studs protruding from the

bottom of the Mounting bracket are

installed with threads all the way through

the bracket.

Pass leadwires and safety cable

through the canopy.

Remove side covers from canopy expos-

ing 4 holes. 2 closed holes and 2 open

“L” shape holes.

FFlluusshhMMoouunnttIInnssttaallllaattiioonn

Lift Canopy allowing the 2 studs to

protrude through the canopy.

Next lift the canopy disk and install

knurled nuts as shown. Tighten the

knurled nuts securely. The canopy should

adjust for any irregularity in the ceiling or

Outlet box.

Connect black and blue wire from fan to Black or (Hot)

wire from house. Connect White wire from Fan to

White (Neutral) wire from house. Connect Ground

leads from mounting bracket and downrod to Ground

lead from house. Refer to Safety Tips section of

manual.

Canopy disk

House Fan

Blue

Black

White

Green

Black

White

Ground

Lag Screw

Washer

Lock Washer

Safety Cable

Go to Step 26

Install rubber pad between fan

body and canopy.

Remove every other screw as circled

and save for later use.

Place blade holders onto blades aligning holes in

blade holder with holes in blade. Make sure that the

side of the blade you select is facing downward.

Install 3 screws and fiber washers to back side of

blade as shown. Tighten screws securely. Repeat

this process 4 more times until all blades are assem-

bled.

Install blades to motor using the 10

motor screws provided. Tighten

screws securely.

26 27

Lift fan to mounting bracket, aligning the “L”

shape holes on the canopy with the screws on

the mounting bracket. Turn the fan clock-

wise to lock in position. Re-install the screws

removed in the previous step and tighten

securely.

Remove switch cap housing from fan.

Remove the plug from center of fit-

ter. Install switch cap housing to light

kit by turning clockwise to tighten.

Remove nut and save for next step.

Remove the all thread studs from the lower

part of the mounting bracket. Hang fan

from mounting bracket by the hands

free hook into a closed hole on the

edge of the Canopy. Note: For

Canadian mounting refer to Step #8.

Hands free hook

Take 4 screws from hardware pack

and insert 2 one on each side of

bracket to match the L slot screw

holes in canopy. Keep 2 screws for

later use.

Replace the 3 screws removed and

tighten securely. Check motor for

shipping stabilizers and remove if

present.

Place canopy over fan body

aligning holes.

Make wire connections to power source using wire nuts

provided. Make sure that no filiments are outside of

the wirenut. After making the wire connections, the

wires should be spread apart with the grounded con-

ductor and the equipment-grounding conductor on one

side of the outlet box and ungrounded conductor on

the other side of the outlet box.

Connect black and blue wire from fan to Black or (Hot)

wire from house. Connect White wire from Fan to

White (Neutral) wire from house. Connect Ground

leads from mounting bracket and downrod to Ground

lead from house. Refer to Safety Tips section of

manual.

House Fan

Blue

Black

White

Green

Black

White

Ground

Install keeper nut over lead wires.

Tighten keeper nut onto threaded

pipe from the light kit.

Install 3 x 60 watt Candelabra base

bulbs.

Locate blue and white wire from the fan

marked “For light kit”. Connect blue from fan

to black from light and white from fan to white

from light by pushing connectors together.

Install finial cap and finial nut to

glass and tighten finial nut.

Attach switch cap to fan by lining up

2 slot ear holes and 1 screw hole and

twisting cap. Then tighten the 3

screws.

Install rubber washer and hex nut to

glass tighten nut.

Remove finial nut, finial cap, hex nut,

and washer from fitter.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate

when switch is in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor (see installation

step #13).

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glass-

ware are finger tight. Check to be sure light bulb is tight in socket and not touching glass

shade(s). If vibration persists from glass, remove glass and install a 1/4" wide rubber band

on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.

5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State variable speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball. (See illus-

tration in Step #6 of Downrod Mount installation).

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the washer if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Customer Service Center

740 S.W. Loop 820, Suite 110

Fort Worth, Texas 76115

1-800-519-4092

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3JVR44 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SCR60BR3 Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Colony 5COM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5BR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MAVR60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3ELR44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Hicks 3HCKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AKR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EM60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5AB52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3VMR52XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MQ60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ED56WAD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Jovie 3JVR58 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 4TK52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ASPR70 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5SRR54XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 4MDR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 8ATR44 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO44 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR72 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MGMR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3AMR60BSD Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung