Monte Carlo Fan Company Jovie 3JVR58 Series Gebrauchsanweisung

Total fan weight

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

Attach sales receipt to this card and retain as yourproof of purchase

To register your fixture, please visit our website www.montecarlofans.com

3JVR58XXX Series Fan

cETL Model NO. : 3JVR58XX

6.56 kg

14.43 lbs

Owner’s Guide and Installation Manual

Cautions and Warnings

Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with applicable codes and standards (ANSI/NFPA 70), including

ﬁre-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side

of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed

carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to

prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the ﬂoor

to the trailing edge of the blade.

WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of 15.9 kg (35 lbs)

or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts

In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to the building structure (or the

ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert

foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of ﬁre or electric shock, this fan should only be used with fan speed control part no. JY1126R manufactured by Satellite

Electronic (Zhongshan) Ltd.

WARNING: To reduce the risk of ﬁre or electric shock, do not use this fan with any other solid state fan speed control device, or variable speed control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airﬂow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment

manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

CAUTION: The light source is designed for this speciﬁc application and can overheat if serviced by untrained personnel. If any servicing is required, the

product should be returned to an authorized service facility for examination or repair.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

1 2 3

4 5 6

OFF

Before you begin installing the fan, Switch

power off at Service panel and lock

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a warning device, such

as a tag, to the service panel.

Use AC 120V/60HZ power supply

only.

Before installing this fan make sure the

outlet box is properly installed to the

house structure. To reduce the risk of

ﬁre, electric shock, or personal injury,

mount to outlet box or supporting system

acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan

support and use only the screws provided

with the outlet box (must support 35

lbs). Before attaching fan to outlet box,

ensure the outlet box is securely fastened

by at least two points to a structural

ceiling member ( a loose box will cause

the fan to wobble).

Install the mounting bracket onto the

outlet box.

Partially loosen the two screws on the

outlet box, attach the mounting bracket

onto the outlet box by sliding it over the

two screws as shown in the illustration.

Have the mounting bracket in position

and tighten the set screws.

Install a blade bracket onto blade with a

blade bottom plate using set screws

provided. Repeat this process for

remaining blades.

Put motor assembly on a suitable area of

paper pulp.

Remove the set screws (the bigger

screws) of blade bracket with rubber

washer from motor. Do not remove the

other screws (the smaller screws).

Install the blade assembly to motor using

the set screws with rubber washers that

are removed in the last installation step.

Tighten screws securely. Repeat this

process for remaining blade assemblies.

Set screw

Blade bracket Blade

Blade bottom plate

Mounting bracket

Set screw

with washer

Set screw

with washer

7 8

10 11 12

Remove the set screws from yoke. Keep

the screws.

Place the top housing over lead wires,

safety cable and the yoke. Replace the

set screws and tighten all the screws.

Partially loosen downrod set screws from

yoke at top of motor assembly.

Remove preassembled cross pin and

keeper pin from downrod. Keep parts.

Place downrod over canopy, canopy

bottom cap and yoke cover.

Connect the extension lead wires to the

lead wires from motor. Make sure the

quick connectors are clasped ﬁrmly.

Thread lead wires and safety cable from

motor assembly through downrod.

Note: Make sure the plugs connections

won’t be pulled apart.

Slip downrod into motor housing yoke,

aligning holes and install cross pin and

keeper pin.

Insert cross pin through yoke and downrod

until point appears on the other side, and

insert keeper pin on cross pin.

Pull the downrod up tight against the

cross pin, and then evenly tighten the

downrod set screws on motor housing

yoke.

Place yoke cover on top housing of fan.

Warning: Cross pin and keeper pin must

be installed securely, failure to install them

will result in serious injury.

Install ball end of downrod into mounting

bracket opening. Align (engage) slot on

ball with tab on mounting bracket.

Warning: Failure to align slot on ball with

tab may result in serious injury.

Important: If using the angle mount,

make sure open end of mounting bracket

is installed facing the higher point of the

ceiling and make sure the ceiling angle is

not steeper than 20º. Longer downrod

may be necessary allowing the fan blades

to rotate without obstructions.

Safety cable must be installed into the

house structure using 3” lag screws,

washers, and lock washers provided,

required for outdoor applications and in

Canada (All fans installed in Canada), and

for USA fan and light kit combinations

over 35lbs.

Make sure that when the safety cable is

fully extended the lead wires are longer

than the cable and no stress is placed on

the lead wires.

Note: If Installing The Secondary Support

Safety Cable in the U.S., Do Not Remove

Knockouts In The Outlet Box.

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Keeper pin

Cross pin

Top

housing

Yoke

Downrod

Cross pin

Keeper pin

Tab

Slot

Tighten the screws

Canopy

Downrod

Canopy bottom

cap

Yoke cover

Extension lead wire

14 15

Make wiring connections using wire connectors provided as indicated above.

Brown wire from fan to Brown wire from receiver marked Motor U.

Gray wire from fan to Gray wire from receiver marked Motor V.

Blue wire from fan to Blue wire from receiver marked Motor W.

White (Neutral) wire from house to White wire from remote marked AC IN N.

Black (Live) wire from house to Black wire from remote marked AC IN L.

Connect all green grounded wires to Grounded wire from House.

Make sure that no ﬁlaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices after being

made should be turned upward and pushed carefully up into the outlet box.

Caution: The installation has to be complete before operate the fan. Receiver has to be used on the fan and cannot be bypassed.

Blue

Brown Grey

Black

Receiver

Ground/Green

Wall switch

Power source

White

Partially loosen one and remove one

preassembled step screw from mounting

bracket (Do not remove the other set

screws). Save the screw.

Lift canopy up, aligning its keyhole slot

with the preassembled step screw on

mounting bracket and twist clockwise to

lock in place. Reinstall the other step

screw and tighten the screws securely.

Attach canopy bottom cap onto canopy

by aligning its holes with the step screws

on mounting bracket and ﬁx it with the

magnet embraced in the cap.

Canopy bottom

cap

Step screw