Monte Carlo Fan Company Drawing Room 5ED56 D-L Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach sales receipt to this card and retain as your proo o purchase

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To register your ixture, please visit our website www.montecarlo ans.com

5ED56XXD-L Series Fan

Total an weight with light kit

UL Model No. : AC-556LF5800OD

12.38kgs

27.24 lbs

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING

READ AND SAVE THESE INSTRUCTIONS

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! ead all instructions and safety information before installing your new fan. eview the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To educe The isk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and egulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not e-

move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, efrigeration and Air Conditioning Engineers (ASH AE) and the local code authorities.

CAUTION: To educe the isk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Note: Use only with light kits marked suitable for use in wet locations.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools equired for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Place canopy and then yoke cover over downrod

as shown. Then thread the lead wires and safe -

ty cable from fan through the downrod as

shown.

Before you begin installing the fan, S witch power off

at Service panel and lock service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent w arning device,

such as a tag, to the service panel.

Before installing this fan make sure the outlet

box is properly installed to the house structure.

To reduce the risk of fire, electric shock, or per -

sonal injury, mount to outlet bo x or supporting

system acceptable for fan support.

(Mounting must support at least 35 lbs.)

Use metal outlet box suitable for fan support

(must support 35 lbs). Before attaching fan to

outlet box, ensure the outlet bo x is securely

fastened by at least two points to a structur al

ceiling member ( a loose bo x will cause the fan

to wobble). Use only the screws provided

with the outlet box.

Remove keeper from pin. Pull pin out and

replace keeper, save for later.

Loosen the 2 set screws and nuts till y ou can

not feel them on inside of y oke.

Tighen set screws and nuts to secure

downrod in yoke.

Insert downrod into yoke on top of

fan body. Align the hole in the down -

rod with hole in the y oke. Insert pin

through the yoke and downrod until

the point appears on the other side.

Install the keeper.

Check the fan motor for shipping sta -

bilizer and remove if present.

Carefully lift fan assembly onto mounting br ack-

et. Rotate fan so that the notch on the ball

engages the ridge in the mounting br acket. This

will allow hands-free wiring.

Attach blade assembly to motor

using the motor screws and w ashers

provided. Tighten screws securely.

Remove 1 screw and loosen 2

screws.

Make wire connections to power source using

wire nuts provided. Make sure that no filiments

are outside of the wirenut. After making the

wire connections, the wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and ungrounded conductor on

the other side of the outlet bo x.

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house ma y

vary in color and ma y not include ground wire.

After wiring is conplete, gently push wires into

junction box with wire nuts pointing upw ard.

Refer to point 3 of safet y tips.

For control of fan and optional light from w all

location, follow diagram above. NOTE: A profes-

sional electrician is recommended for this t ype

of installation.

Light Switch

Fan Switch

Wall

Control

Attach blade brackets to blades using

the blade bracket screws and wash-

ers provided.

Loosen one and remove one preassem-

bled screw from mounting bracket.

Save screw. Lift canopy up, aligning its

keyhole slot with the preassembled

screw on mounting bracket and twist

clockwise to lock in place. Re-install the

removed screw and tighten all screws

securely.

For Canadian installation and for USA fan and light

kit combinations over 35 lbs, in both flush and

downrod modes the safety cable must be installed

into the house structure beams using 3” lag

screws, washers and lock washers provided. Make

sure that when the safety cable is fully extended

the lead wires are longer than the cable and no

stress is placed on the lead wires.

48+:If Installing The Secondary Support Safety

Cable in the U.S., Do Not Remove Knockouts In

The Outlet Box.

 Safety cable installation

!',+8='(1+

'-!)6+;

safety

cable

3” lag

screw

lock

washer

Install switch plate by placing over

the 2 screws and twisting into place.

Install screw removed and tighten all

3 screws securely.

Push plug from fan and plug from

switch plate together.Match the color

strips on the plugs.

Put plug from fan through hole in

switch plate.

Install glass and finial nut.

Plug white wire from fan to white

wire from light kit. Then plug blue

wire from fan to black wire from

light kit.

23 24

Loosen 2 screws and remove 1 screw

from light pan. Save screw for

later use.

Install 3 x 40 watt candelabra bulbs. Bulbs

included.

WARNING: Over lamping the fan will

result in the fan lights shutting down

until the proper wattage of bulbs are

installed.

Reset the lights by turning off the wall

switch, breaker,or by remote. Replace

bulbs with the correct wattage bulbs, turn

the power on.

Attach light fixture by aligning keyhole

slots on light fixture with screws on light

pan and twist clockwise till lock. Re-install

the screw removed in step 22. Tighten all

screws securely.

1.Check main and branch circuit fuses or circuit break ers.

2.Check line wire connections to fan and switch wire connections in switch housing.

3.Make sure that any shipping stabilizer has been removed from motor.

CAUTION: Make sure main power is turned off.

1.Check to make sure all screws in motor housing are snug (not o ver tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not r attling against each

other or against the interior w all of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.Some fan motors are sensitive to signals from Solid State v ariable speed controls. DO

NOT USE a Solid State variable speed control.

5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canop y engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor .

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade lev els are unequal. Check this lev el by

selecting a point on the ceiling abo ve the tip of one of the blades. Measure this distance

from blade tip to ceilng. K eeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade lev els are not equal, y ou can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a w asher

(not supplied) between the blade and blade holder at the screw closest to the motor . To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the w asher if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can

redistribute the weight and possibly result in smoother oper ation.

1.Check wire from fan to mak e sure it is connected to hot wire from house.

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

WARNING: Over lamping the fan will result in the fan lights shutting down

until the proper wattage of bulbs are installed.

Reset the lights by turning off the wall switch, breaker,or by remote. Replace bulbs with

the correct wattage bulbs, turn the power on.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not

start:

3. If fan wobbles:

4. If light does not

work:

Trouble Shooting

If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation,

or wiring. In some cases, these installation errors ma y be mistaken for defects. If you experience any faults,

please check this Trouble Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty

in installation, please call our Customer Service Center at the number printed on y our parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis -

connecting means to prevent power from being switched on accidentally. When the service dis -

connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Trouble Suggested Remedy

Jul.2013 Update for CUL regulation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company 3TAR56 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3BRYSM60D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MQ60XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LLR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CMR56 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DVR68 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5GIR54XXD-L Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company Rockland 4RKR60 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF42 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5ASPR56 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3CLMR56XXD Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MZR54 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CNR52XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company AC-552 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3SU54 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DOR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIC44XXXD-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3RZHR52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIO52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CLR66XXD-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCM52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42 Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung