Monte Carlo Fan Company 5WF42 Series Gebrauchsanweisung

Owner’s Guide and Installation Manual

Attach ale receipt to thi card and retain a your proof of purcha e

DATE OF PURCHASE:

MODEL NUMBER:

RETAILER NAME:

RETAILER ADDRESS:

To regi ter your fixture, plea e vi it our web ite www.montecarlofan .com

5WF42XX Series Fan

Total fan weight

UL Model No. : AC-542OD

5.69kgs

12.52 lbs

WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G

READ A D SAVE THESE I STRUCTIO S

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA

70-1999), including fire-rated construction.

Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be

turned upward and pushed carefully up into the outlet box.

WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Be cautious! ead all instructions and safety information before installing your new fan. eview the accompanying assembly diagrams.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor to the trailing edge of the blade.

WARNING: To educe The isk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of

15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.

CAUTION: For Compliance with Local Codes and egulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not e-

move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to

the building structure (or the ceiling joist).

WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do

not insert foreign object between rotating blades.

Attach the mounting bracket using only the hardware supplied with the outlet box.

WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.

WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed

control.

If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

Never place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating

equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, efrigeration and Air Conditioning Engineers (ASH AE) and the local code authorities.

CAUTION: To educe the isk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.

All set screws must be checked and tightened where necessary before installation.

Note: Suitable for use in wet locations when installed in a GFCI protected branch circuit.

Note: Use only with light kits marked suitable for use in wet locations.

Customer Service

800-969-3347

Customer Service Center

7400 Linder Ave.

Skokie, IL 60077

www.montecarlofans.com

Tools equired for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,

Stepladder and Wire Strippers.

Before you begin installing the fan, Switch power off

at Service panel and lock service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warn-

ing device, such as a tag, to the service panel.

Before installing this fan make sure the outlet box is

properly installed to the house structure. To reduce

the risk of fire, electric shock, or personal injury,

mount to outlet box or supporting system acceptable

for fan support. (Mounting must support at least 35

lbs.)

Use metal outlet box suitable for fan support (must

support 35 lbs). Before attaching fan to outlet box,

ensure the outlet box is securley fastened by at

least two points to a structural ceiling member ( a

loose box will cause the fan to wabble). Use only

the screws provided with the outlet box.

Loosen set screws with locking nuts and

remove keeper from pin and then pin from

yoke for downrod (see inset).

Install downrod with canopy and yoke covers

into yoke. Align hole in downrod and yoke,

push pin through and replace keeper. Tighten

set screws and locking nuts (see inset).

Install downrod to canopy and then install yoke

cover to downrod. Thread wires and safety

cable through downrod

Hang assembled fan from the mounting bracket

installed to ceiling in previous steps. Make sure the

fan is hanging straight. Rotate fan until the tab on

the Mounting bracket engages the slot on the

Downrod Ball. This must be done to prevent the fan

body from rotating when the blades are in motion.

Check the motor for plastic shipping sta-

bilizer tabs and remove them if they are

present.

For Canadian installation and for USA fan and light

kit ombinations over 35 lbs, in both flush and

downrod modes the safety able must be installed

into the house stru ture beams using 3” lag

s rews, washers and lo k washers provided. Make

sure that when the safety able is fully extended

the lead wires are longer than the able and no

stress is pla ed on the lead wires.

Note:If Installing The Se ondary Support Safety

Cable in the U.S., Do Not Remove Kno kouts In

The Outlet Box.

9Safety able installation

Safety Cable

Lag Screw

safety

able

3” lag

s rew

lo k

washer

Make wire connections to power source using wire

nuts provided. Make sure that no filiments are out-

side of the wirenut. After making the wire connec-

tions, the wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet box and

ungrounded conductor on the other side of the outlet

box.

Attach blade brackets to blades

using the blade bracket screws

and washers provided.

The screws, washers, and motor

pads are pre-installed to the blade

holders. Attach blade assembly to

motor and tighten screws securely.

For pullchain controls, follow diagram above.

Make sure that all exposed wiring is secured

inside wire nuts. Note: Wires from house may

vary in color and may not include ground wire.

After wiring is conplete, gently push wires into

junction box with wire nuts pointing upward.

10 House Fan

Black

White

Green

Black

White

Green(downrod)

Green(Bracket)

Blue

Loosen one and remove one pre-

assembled screw from mounting

bracket. Save screw. Lift canopy up,

aligning its keyhole slot with the pre-

assembled screw on mounting

bracket and twist clockwise to lock in

place. Re-install the removed screw

and tighten all screws securely.

1.Check main and branch circuit fuses or circuit breakers.

2.Check line wire connections to fan and switch wire connections in switch housing.

CAUTION: Make sure main power is turned off.

3.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate

when switch is in the middle.

4.Make sure that shipping stabilizer tabs have been removed from motor.

1.Check to make sure all screws in motor housing are snug (not over tightened).

2.Check to make sure the screws which attach the fan blade holder to the motor are tight.

3.Check to make sure wire nut connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before entering switch housing.

4.If using an optional Ceiling Fan Light Kit, check to be sure the screws securing the glass-

ware are finger tight. Check to be sure light bulb is tight in socket and not touching glass

shade(s). If vibration persists from glass, remove glass and install a 1/4" wide rubber band

on glass neck to act as an insulator. Replace glass and tighten screws against rubber band.

5.Some fan motors are sensitive to signals from Solid State variable speed controls. DO

NOT USE a Solid State variable speed control.

6.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear

after this period.

1.Make sure that the ridge of the canopy engages the notch in the downrod ball.

2.Check that all blades are screwed firmly into blade holders.

3.Check that all blade holders are tightened securely to motor.

4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box

and junction box is mounted firmly to ceiling joist.

5.Most fan wobble problems are caused when blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip of one of the blades. Measure this distance

from blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is

positioned for measurement. Repeat for each blade. If all blade levels are not equal, you can

adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer

(not supplied) between the blade and blade holder at the screw closest to the motor. To

adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at

the two screws farthest from the motor. Reverse the position of the washer if blades mount

from top of blade.

6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can

redistribute the weight and possibly result in smoother operation.

1.Check blue wire from fan to make sure it is connected to hot wire from house

2.Check for loose or disconnected wires in fan switch housing.

3.Check for loose or disconnected wires in light kit.

4.Check for faulty light bulbs.

CAUTION: Make sure main power is turned off before entering switch housing.

2. If fan sounds noisy:

1. If fan does not start:

3. If fan wobbles:

4. If light does not work:

TROUBLE SHOOTING

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In

some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble

Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our

Customer Service Center at the

number printed on your parts list insert sheet.

Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

Trouble Suggested Remedy

Jul.2013 Update for CUL regulation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Monte Carlo Fan Company Lüfter Handbücher

Monte Carlo Fan Company

Monte Carlo Fan Company Haven 5HVO52BKD Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HVO52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3LD48 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5MFR52 D Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5WF52 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5RDR Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DS34XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5HS42XX Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LD52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5DIC44XXXD-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CY60XX Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5EPR60BRD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Cupra 3CPR60 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 3TSR52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LNR52 D-L Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3MNLR56 Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CSR60AGD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company Loft 96 6LFR96 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company TRAVERSE 5TV52 D-V1 Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5LCR52 Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 3IKDR52 D Series Gebrauchsanweisung

Monte Carlo Fan Company

Monte Carlo Fan Company 5TV52XXD Series Bedienungsanleitung

Monte Carlo Fan Company

Monte Carlo Fan Company 5CXR52 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung