Morse 86 Bedienungsanleitung

OPERATOR’S MANUAL FOR MORSE MODEL 86 DRUM LIFTER

For handling 55 gallon steel or fiber drum between 22” and 23½”OD and heights between 23” and 38”.

Serial numbers 0502 to 1202 (MMYY)

A. IMPORTANT:

1. Review the Material Safety Data Sheet(s) for the material(s) in the drum(s) and take all necessary precautions.

Safety shoes, work gloves, hard hat and other personal protective devices are recommended.

2. Please read all instructions

thoroughly

before attempting to operate your new MORSE drum handler.

3.The model 86 has a maximum capacity rating of 1000 Lb.and is designed to lift and move drums of size and type noted above.

NOT

exceed this load rating. Exceeding this rating or handling drums other than those mentioned above is unsafe and could result

in equipment damage, excessive wear or awkward handling.

4.When loading, unloading, operating, or maintaining your MORSE drum handler, always use care and good judgment, have good

footing and a firm hold. Keep hands and loose clothing, etc. away from all moving parts. Never allow anyone to be below any part

of a raised drum handler or drum. Read operating instructions and review the pictures in the sales brochure before operation.

5.The Model 86 is a “Group 1 Structural and Mechanical” Below-the-Hook Lifting Device which is covered by the American National

Standard ANSI/ASME B30.20.The user should comply with all aspects of this standard.

B. ASSEMBLY INSTRUCTIONS

1.Prior to use, inspect all moving parts.Inspect cinch chain and ratchet /pawl assembly for proper operation.Perform necessary load

test, inspections, operator training, etc. as prescribed in the ANSI/ASME B30.20 standard.

C. OPERATING INSTRUCTIONS:

1. With the Model 86 on the floor, lower hoist and engage

hoist hook into the lifting eye.

2. Raise hoist to lift the 86 clear of the floor and move it to the

drum.

3. Position the 86 with the base at floor level and near or

against the base of drum.

4. Using a drum hand truck (ie. Morse Model 160), carefully

place the drum onto the base of the 86 so that the drum

rests into the saddle band (see Figure 1).

5. Drape the cinch chain (item 4) across the face of the drum

and engage a link into the slot on the ratchet and tighten

the cinch chain around the drum by turning the ratchet

handle clockwise.

6. Raise hoist and move drum to desired location.

7.To remove drum from the 86, release tension in the cinch

chain(item 4) byturning ratchethandle clockwiseto relieve

the force on the pawl (item 8), and lifting the pawl away

from the ratchet. Once the cinch chain is slack, remove the

link from the slot in the ratchet. Remove the drum from the

86 using a drum truck.

CAUTION:

DO NOT exceed weight capacity of 1000 Lb.

D. MAINTENANCE:

Periodically inspect all moving parts, framework, cinch chain, and contact areas for signs of wear, fatigue, or loosening. Perform

all inspections, load tests, and maintenance according to the ANSI/ASME B30.20 standard.

MORSE

MODEL86

MORSE

MODEL160

55GALLON

“POLY”DRUM

Figure1

MORSE MFG. CO., INC. • 727West Manlius Street • P.O. Box 518 • East Syracuse, NY 13057-0518

Phone: 315-437-8475 • Fax: 315-437-1029 • Email: service@MORSEmfgco.com • Website: www.MORSEmfgco.com

MODEL 86

DRUM LIFTER

TheSpecialist In Drum HandlingEquipment

Parts List and Diagram

Serial numbers 0502 to 1202 (MMYY)

ITEM QTY P/N DESCRIPTION

1 1 2645-P FRAME WELDMENT,86

2 1 82-P 3/8 -16 X2-1/4 HHCS GR 2 STL

3 1 1169-P 3/8 - 16 REVHEXLOC NUT

4 1 180-P CHAIN,CINCH,3/16 ALLOY33 LK

5 1 727-P RATCHET PLATE CPTW/ TAB 1/4"

6 1 1296-P 1/4 - 20 X7-½ HHCS GR 5 STL

7 1 1297-P 1/4 - 20 REVHEXLOC NUT

8 1 168-P PAWL, WITH DRILLED HOLE

9 1 169-P PAWL SPRING

10 1170-P 3/8" DIA X5/8" SHOULDER SCREW

MODEL 86

DRUM LIFTER

TheSpecialist In Drum HandlingEquipment

Website: www.MORSEmfgco.com

Inhaltsverzeichnis

Andere morse Hebesystem Handbücher

morse

morse 515-N-115 Bedienungsanleitung

morse

morse 82A-GT Series Bedienerhandbuch

morse

morse 185i/E Bedienungsanleitung

morse

morse 525-N Bedienungsanleitung

morse

morse 515M-T-114 Bedienungsanleitung

morse

morse 185A-HDSS Bedienungsanleitung

morse

morse PILOT 910 Bedienungsanleitung

morse

morse 400AM-60 Bedienungsanleitung

morse

morse 525-N-115 Bedienungsanleitung

morse

morse 82H-124 Bedienungsanleitung

morse

morse 185AM Bedienungsanleitung

morse

morse 510-120 Bedienungsanleitung

morse

morse 400AM-96-114 Bedienungsanleitung

morse

morse 525-N-115 Bedienungsanleitung

morse

morse 82A-120 Bedienungsanleitung

morse

morse 400A-96-114 Bedienungsanleitung

morse

morse 410M-124 Bedienungsanleitung

morse

morse 400A-96SS-127 Bedienungsanleitung

morse

morse 510M-124 Bedienungsanleitung

morse

morse 195AM-A Bedienungsanleitung

morse

morse 520-120 Bedienungsanleitung

morse

morse 195A-A Bedienungsanleitung

morse

morse PILOT 900 Bedienungsanleitung

morse

morse 91 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung

Ricon

Ricon Mirage F9T Bedienungsanleitung

morse 86 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken