Motorline professional KFM Gebrauchs- und Pflegehandbuch

V5.1

REV. 02/2022

KFM EN

USER’S AND INSTALLER’S MANUAL

A B

11B

10B

10A

10B

10A

10B

11A

ENEN

. CONTENT . SAFETY INSTRUCTIONS

INDEX

This product is certified in accordance with European

Community (EC) safety standards.

This product complies with Directive 2011/65/EU of the

European Parliament and of the Council, of 8 June 2011, on

the restriction of the use of certain hazardous substances in

electrical and electronic equipment.

(Applicable in countries with recycling systems).

This marking on the product or literature indicates that the

product and electronic accessories (eg. Charger, USB cable,

electronic material, controls, etc.) should not be disposed

of as other household waste at the end of its useful life. To

avoid possible harm to the environment or human health

resulting from the uncontrolled disposal of waste, separate

these items from other types of waste and recycle them

responsibly to promote the sustainable reuse of material

resources. Home users should contact the dealer where they

purchased this product or the National Environment Agency

for details on where and how they can take these items

for environmentally safe recycling. Business users should

contact their vendor and check the terms and conditions

of the purchase agreement. This product and its electronic

accessories should not be mixed with other commercial

waste.

This marking indicates that the product and electronic

accessories (eg. charger, USB cable, electronic material,

controls, etc.) are susceptible to electric shock by direct or

indirect contact with electricity. Be cautious when handling

theproductandobserveallsafetyproceduresinthismanual.

ATTENTION:

INSIDE PACKAGE

DIMENSIONS

CONNECTION SCHEME

PREPARATION

PROGRAMMING THE MOTOR COURSE

TECHNICAL SPECIFICATIONS

. SAFETY INSTRUCTIONS

. PACKAGE

. AUTOMATION

. INSTALLATION

. PROGRAMMING

INSTRUCTIONS FOR FINAL CONSUMERS

V MOTOR

INSTRUCTIONS FOR FINAL TECHNICIANS

. TROUBLESHOOTING

. COMPONENTS TEST

PROGRAMMING REMOTE CONTROLS

DELETE REMOTE CONTROLS

FORCE ADJUSTMENTS

SLOWDOWNTIME TIME SETTING

STOP SPEED/DECELERATION RAMP SETTING

SLOWDOWN SPEED SETTING

REVERSE MOTOR DIRECTION

FOLLOW ME

ENABLE/DISABLE PHOTOCELLS

AUXILIARY LIGHT CONNECTOR

ENABLE/DISABLE AUTOMATIC CLOSE

HUMAN PRESENT

OPERATING LOGIC

PREFLASHING LIGHT

ERROR CODES

ENGINE'S INSTALLATION IN THE RAIL

INSTALLATION OF SUPPORTS

A B

ENEN

. SAFETY INSTRUCTIONS

GENERAL WARNINGS

•This manual contains very important safety and usage information.

very important. Read all instructions carefully before beginning the

installation/usage procedures and keep this manual in a safe place

that it can be consulted whenever necessary.

•This product is intended for use only as described in this manual. Any

other enforcement or operation that is not mentioned is expressly

prohibited, as it may damage the product and put people at risk

causing serious injuries.

•Thismanual is intendedfirstly for specialized technicians, anddoesnot

invalidate the user’s responsibility to read the “User Norms” section in

order to ensure the correct functioning of the product.

•The installation and repair of this product may be done by qualified

and specialized technicians, to assure every procedure are carried

out in accordance with applicable rules and norms. Nonprofessional

and inexperienced users are expressly prohibited of taking any action,

unless explicitly requested by specialized technicians to do so.

•Installations must be frequently inspected for unbalance and the

wear signals of the cables, springs, hinges, wheels, supports and other

mechanical assembly parts.

•Do not use the product if it is necessary repair or adjustment is

required.

•When performing maintenance, cleaning and replacement of parts,

the product must be disconnected from power supply. Also including

any operation that requires opening the product cover.

•The use, cleaning and maintenance of this product may be carried

out by any persons aged eight years old and over and persons whose

physical,sensorialormentalcapacitiesarelower,orbypersonswithout

any knowledge of the product, provided that these are supervision

and instructions given by persons with experienced in terms of usage

of the product in a safe manner and who understands the risks and

dangers involved.

•Children shouldn’t play with the product or opening devices to avoid

the motorized door or gate from being triggered involuntarily.

WARNINGS FOR TECHNICIANS

•Before beginning the installation procedures, make sure that you have

all the devices and materials necessary to complete the installation

of the product.

•You should note your Protection Index (IP) and operating temperature

to ensure that is suitable for the installation site.

•Provide the manual of the product to the user and let them know how

to handle it in an emergency.

•If the automatism is installed on a gate with a pedestrian door, a door

locking mechanism must be installed while the gate is in motion.

•Do not install the product “upside down” or supported by elements do

not support its weight. If necessary, add brackets at strategic points

to ensure the safety of the automatism.

•Do not install the product in explosive site.

•Safety devices must protect the possible crushing, cutting, transport

and danger areas of the motorized door or gate.

•Verify that the elements to be automated (gates, door, windows,

blinds, etc.) are in perfect function, aligned and level. Also verify if the

necessary mechanical stops are in the appropriate places.

•The central must beinstalled onasafe place ofany fluid(rain, moisture,

etc.), dust and pests.

•You must route the various electrical cables through protective tubes,

to protect them against mechanical exertions, essentially on the

power supply cable. Please note that all the cables must enter the

central from the bottom.

•If the automatism is to be installed at a height of more than 2,5m from

the ground or other level of access, the minimum safety and health

A B

ENEN

. SAFETY INSTRUCTIONS

requirements for the use of work equipment workers at the work of

Directive 2009/104/CE of European Parliament and of the Council of 16

September 2009.

•Attach the permanent label for the manual release as close as possible

to the release mechanism.

•Disconnect means, such as a switch or circuit breaker on the electrical

panel, must be provided on the product’s fixed power supply leads in

accordance with the installation rules.

•If the product to be installed requires power supply of 230Vac or 110Vac,

ensure that connection is to an electrical panel with ground connection.

•The product is only powered by low voltage satefy with central (only at

24V motors)

WARNINGS FOR USERS

•Keep this manual in a safe place to be consulted whenever necessary.

•If the product has contact with fluids without being prepared, it must

immediately disconnect from the power supply to avoid short circuits,

and consult a specialized technician.

•Ensure that technician has provided you the product manual and

informed you how to handle the product in an emergency.

•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,

turn off the power and do not use it until all safety conditions have

been met.

•In the event of tripping of circuits breakers of fuse failure, locate the

malfunctionandsolveit before resetting thecircuitbreaker or replacing

the fuse. If the malfunction is not repairable by consult this manual,

contact a technician.

•Keep the operation area of the motorized gate free while the gate in in

motion, and do not create strength to the gate movement.

•Do not perform any operation on mechanical elements or hinges if the

product is in motion.

RESPONSABILITY

•Supplier disclaims any liability if:

•Product failure or deformation result from improper installation

use or maintenance!

•Safety norms are not followed in the installation, use and

maintenance of the product.

•Instructions in this manual are not followed.

•Damaged is caused by unauthorized modifications

•In these cases, the warranty is voided.

MOTORLINE ELECTROCELOS SA.

Travessa do Sobreiro, nº29

4755-474 Rio Côvo (Santa Eugénia)

Barcelos, Portugal

SYMBOLS LEGEND:

• Important safety

notices

• Useful information

• Programming

information

• Potentiometer

information

• Connectors

information

• Buttons

information

A B

226mm

205mm

81mm

140mm193mm

70mm

2000/3000mm

68mm

xmm

504mm

458mm

ENEN

. PACKAGE . AUTOMATION

INSIDE PACKAGE DIMENSIONS

TECHNICAL SPECIFICATIONS

Elements in the package of 1 motor:

01 • 01 Motoreducer

02 • 01 Motor's control board

03 • 02 4-Channel remote controls

04 • 01 Rail

05 • 04 Rail supports A

06 • 04 Rail supports B

07 • 02 Gate trolley ﬁxing supports

08 • 01 Trolley with unlocker

09 • Mounting accessories

10 • 01 User's manual

Kit components:

KFM and rail dimensions are the following:

Kit package:

Fig. 1

Fig. 3

Fig. 2

This automation can be applied to both folding gates and to sectioned gates.

• Motor 24Vdc

• Power Supply 220/110Vac 10% 50/60Hz

• Operating temperature -25°C to 55°C

• Relative humidity ≤90%

• Opening and closing force 2000N

• Frequency 433.92Mhz

• Code type Rolling Code

• Flashing lamp LED

• Courtesy light time 3 minutes

• Noise LpA <= 50dB (A)

• Working frequency Intensive

• Protection grade IP20

• Maximum weight supported by the rail 500kg



GND Open Stop CloseAlarm 24V PE GND PB

SET

CODE

DOWN

F~ ~

1 2

+-COM NC/

1 2 3 4

V

V

. INSTALLATION

CONNECTION SCHEME

1 • Motor

2 • Encoder (GND)

3 • LED (+)

4 • Motor

5 • Encoder (+5V)

6 • LED (-)

7 • Encoder (Signal)

PB • Pushbutton

PE • Photocells

GND • Common

+24V • 24V Power supply

DExternal buttons connections

(on the box door)

ETransformer

FBattery

EXTERIOR BUTTONS

TRANSFORMER

BATTERY

MOTOR

PUSHBUTTON

PHOTOCELL

Do not change the position of the wires!

See menu 8 to invert the motor direc-

tion.

Do not connect to the control

board when it is on.

A B

1500mm 200mm

Fig. 4

Fig. 6

Fig. 8

Fig. 5

Fig. 7

Fig. 9

Fig. 10

Fig. 11

Fig. 12

ENEN

. INSTALLATION . INSTALLATION

ENGINE'S INSTALLATION IN THE RAIL ENGINE'S INSTALLATION IN THE RAIL

The recommended space to be used between the

rail supports is 1500mm, counting from the center

of the holes of each support.

1• To adjust the mounting bracket installation po-

sition, turn the adjusting nuts as shown in ﬁgure

12.

Use the screws that are inside the as-

sembly accessory bag.

Fig. 12

1• Remove the automation cover and loosen the

screws.

3• Place the motor in the rail by inserting the ou-

tput shaft into the rail's hexagon ﬁtting.

5• Adjust the chain tension by tightening or loo-

sening the nut.

2• Turn the automation over and open it by pulling

the casing up.

4• Close the automation by reassembling the co-

ver and the casing.

6• When ﬁnished, insert the ﬁxation screws.

7• Tighten the motor ﬁxation screws to the plate.

INSTALLATION OF SUPPORTS

A B

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

Fig. 14 Fig. 15

Fig. 16

Fig. 22

Fig. 18

Fig. 24

Fig. 21

Fig. 17

Fig. 23

Fig. 19 Fig. 20

Fig. 13

ENEN

. PROGRAMMING

PREPARATION

. PROGRAMMING

1• When turning on the power, the courtesy light will

be active for a few seconds and the display will show

a value ranging from "9" to "0". Then, the automation

enter in stand-by mode.

2• At the end the display will show the signs " " or

"-" signs. The automation is ready to be programmed.

In the diagram below you can see the automation control board, as well as the legend of the buttons to

be used for programming.

Display

CODE Button

UP Button

DOWN Button

SET Button

Keep the trolley locked, pull and push the door manually. Make sure the trolley is connected

to the power supply.

PROGRAMMING THE MOTOR COURSE

1• Press and hold the SET button

until menu 1 appears.

1• Click on the CODE button. The

display will show" ".

2• Then press and hold the UP

button. The display will ﬂash with

"".

2• Click on a button of the trans-

mitter and then click on the but-

ton of the remote control again.

The display will show " " ﬂashing.

3• When the door fully opens,

click the SET button and th " "

will appear.

3• When the conﬁguration is

complete, the function shown

in the ﬁgure will appear on the

display.

6• When the conﬁguration is

complete, the function " " will

appear on the display.

4• Press and hold the DOWN but-

ton. The display will be ﬂashing as

shown in the ﬁgure.

5• When the door closes, click

SET. The door will automatically

open and close to set forces and

sensitivities.

PROGRAMMING REMOTE CONTROLS

To avoid coding errors, it is recommended not to exceed the maximum limit of 20 stored

codes.

A B

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

Fig. 25 Fig. 27

Fig. 26

Fig. 28 Fig. 30Fig. 29

Fig. 33Fig. 32

Fig. 35

Fig. 31

Fig. 34 Fig. 36

ENEN

. PROGRAMMING . PROGRAMMING

DELETE REMOTE CONTROLS

STOP SPEED/DECELERATION RAMP SETTING

1• When the control board rea-

ches the maximum limit of 20

codes stored, the "F" function

ﬂashes.

2• Press and hold the CODE but-

ton for 8 seconds " " will appear

on the display.

3• The "C" function will ﬂash.

All codes have been eliminated.

1• Press and hold the SET button

until the menu 3 appears. Click

SET again to enter the menu.

2• The current force value is dis-

played. By default the value is

"5". Click UP to increase or DOWN

to decrease.

3• Click SET to conﬁrm the se-

lected value. Force values range

from "1" to "9".

FORCE ADJUSTMENTS

SLOWDOWNTIME TIME SETTING

After completing this conﬁguration, for safety, you should verify that the the conﬁgured force

is correct. If "b" appears, you must program the motor course again, with the desired force.

1• Press and hold the SET button

until the menu 5 appears. Click

SET to enter.

1• Press and hold the SET button

until the menu 6 appears. Click SET

to enter.

2• Click UP/DOWN to change the

value between "1" and "6" (each

value represents a 5% variation

of the slowdown time).

2• Click UP/DOWN to change the

value between "4" and "7" (each

value represents a 10% change in

total speed).

3• Click on SET to conﬁrm the

value you have set and then "-"

starts ﬂashing while the course

is fully recognized. This action

occurs whenever you change the

value of this parameter.

3• Click on SET to conﬁrm the

value you have set and then "-"

starts ﬂashing while the course

is fully recognized. This action

occurs whenever you change the

value of this parameter.

The higher the selected value, the greater the slowdown distance.

The lower the selected value, the lower the stopping speed.

A B

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

SET

CODE

DOWN

Fig. 39

Fig. 42

Fig. 38

Fig. 41

Fig. 37

Fig. 40

Fig. 43 Fig. 45Fig. 44

Fig. 46 Fig. 48

Fig. 47

ENEN

. PROGRAMMING. PROGRAMMING

"FOLLOW ME"

0 = Invalid function;

1 to A = 1 to 10 seconds;

This function only works when using automatic closing and photocells.

1• Press and hold the SET button

until menu 9 appears. Clic SET to

enter.

2• Click UP/DOWN to change the

value between "0" and "A". 3• Click SET to conﬁrm the value

you set.

If you do not use photocells, make sure the display is showing "¦ ¦." in order to keep this

function inactive. When the photocell function is active and you try to close the door, the

display will show "" ﬂashing, if they are obstructed.

1• Press and hold the DOWN but-

ton until "¦ ¦." appears. Click SET to

enter the menu.

2• To enable the photocells select

"H." (UP button). To disable photo-

cells, select "¦ ¦."(DOWN button).

3• Click SET to conﬁrm the selec-

ted value and exit.

ENABLE/DISABLE PHOTOCELLS

REVERSE MOTOR DIRECTION

1• Press and hold the SET button

until menu 8 appears. Click SET to

enter.

4• Reprogram menu 1 and 2.

2• If the motor movement direc-

tion does not match what you

want, change between (0 or 1).

3• Click SET to conﬁrm the value

you set.

SLOWDOWN SPEED SETTING

1• Press and hold the SET button

until the menu 7 appears. Click

SET to enter.

2• Click UP/DOWN to change the

value between "0" and "9". Se-

lect the appropriate deceleration

time.

3• Click on SET to conﬁrm the

value you have set and then "-"

starts ﬂashing while the course

is fully recognized. This action

occurs whenever you change the

value of this parameter.

The lower the selected value, the shorter the deceleration time.

The higher the selected value, the longer the deceleration time, working smoother.

Inhaltsverzeichnis

Andere Motorline professional Toröffner Handbücher

Motorline professional

Motorline professional KAPV100 Bedienungsanleitung

Motorline professional

Motorline professional J400 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional BRAVO500-50 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional MC52 Bedienungsanleitung

Motorline professional

Motorline professional MC62 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional WING400 Bedienungsanleitung

Motorline professional

Motorline professional PERGOLA Bedienungs- und Installationshandbuch

Motorline professional

Motorline professional LINCE 400 Bedienungsanleitung

Motorline professional

Motorline professional TELICA Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional SUBWING 700 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional LINCE Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional MF2020 Betriebsanleitung

Motorline professional

Motorline professional LINCE300 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional LINCE Series Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional KVM205 Bedienungsanleitung

Motorline professional

Motorline professional KVM205 Bedienungsanleitung

Motorline professional

Motorline professional LINCE 300 Bedienungsanleitung

Motorline professional

Motorline professional KVM105 Bedienungs- und Installationshandbuch

Motorline professional

Motorline professional JAG400 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional LINCE Series Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional SPIN Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional TEC100 Bedienungs- und Installationshandbuch

Motorline professional

Motorline professional PERSA 400 Gebrauchs- und Pflegehandbuch

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beliebte Toröffner Handbücher anderer Marken

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung

Comunello Automation

Comunello Automation ABACUS 220 Bedienungsanleitung

CAME

CAME FA40230CB Bedienungsanleitung

Mighty Mule

Mighty Mule 200 E-Z GATE OPENER UL325 SERIES Bedienungsanleitung

Riello Elettronica

Riello Elettronica CARDIN ACE FAST Handbuch