Motorola MaraTrac Advanced Control Head Bedienungsanleitung

Motorola

MaraTrac

Advanced Control Head

Operating Instructions

To Receive:

Turn the control head ON/OFF switch to ON. A tone(s) sounds to indicate the radio

condition (see TONE TABLE). The display indicates the receive mode. Ad ust the

volume with the Vol up/down rocker button. The B SY indicator lights when the

channel has activity.

To Transmit:

Scroll to the desired mode using the Mode up/down rocker button. Press and hold

the PTT button; when the red XMIT indicator comes on, speak into the microphone

in a normal voice. If a tone sounds when you press the PTT button, the system is

alerting you to a certain condition (see TONE TABLE).

TONE TABLE

Tone Cause What To Do

1 High-Pitched Beep at Power-Up

Radio Passed Self-Test No Action Necessary

Series of High-Pitched Beeps

at Power-Up

Radio Did NOT Pass

Self-Test

Radio Requires Service;

Notify Service Personnel

1 Low-Pitched Beep Tone Invalid Selection Select Another Button

1 High-Pitched Beep "CHIRP" Valid Selection No Action Necessary

Low Constant Tone When

Pressing PTT *

Transmitting MDC Data Wait for Tone to Complete

Before Talking

Low Constant Tone Upon

Pressing PTT

Blank Transmit Frequency Selected Mode is Receive-Only

Low Constant Tone While

Transmitting

Time-Out Timer Has Expired

Transmission Terminated;

Release PTT

* Optional tone dependent on radio programming

Talk-around:

Use the Direct button for talk-around operation. When the Dir indicator is not lit, the

programmed transmit frequency and squelch information are used. By momentarily

pressing Dir (indicator lights), talk-around is enabled and the receive frequency and

squelch code are used for talk-around transmit frequency information. To turn talk-

around off, momentarily press Dir again.

Multiple PL Codes:

Momentarily press the MPL button to turn on multiple PL feature. The MPL indicator

lights and the selected code is momentarily displayed. When MPL is active, the

selected code overrides the mode-slaved Tx and Rx squelch codes. To turn MPL

off, momentarily press MPL again. To change the selected MPL code, press and

hold the MPL button until a "chirp" sounds and the MPL indicator flashes to indicate

you are in the MPL "configuration" mode. Use the Mode up/down rocker button to

scroll to the desired MPL code. The new displayed MPL code pair becomes

Motorola

MaraTrac

Advanced Control Head

Operating Instructions

immediately active (even before exiting the configuration mode). To exit the

configuration mode, press either the MPL or the Home button.

Monitor VHF/ HF:

The system defaults to coded-squelch operation on power-up. To change to carrier

squelch, momentarily press the Mon button; a single "chirp" sounds and the Mon

indicator lights up. Return to coded-squelch by momentarily pressing Mon again. To

un-squelch the radio, press and hold Mon until a second "chirp" sounds. Ad ust the

volume with the Vol up/down rocker button. Momentarily press Mon again to return

to coded squelch operation.

Low Band Radio with Adjustable Squelch:

The ad ustable squelch control feature allows the operator to ad ust the squelch

threshold, via a squelch control knob located on the control head.

• Coded-Squelch Operation

The radio defaults to coded squelch operation upon powering up. To change to

ad ustable carrier squelch, if Private-Line

(PL) or Digital Private-Line

(DPL) is

programmed, momentarily press the Mon button; a single "chirp" sounds and the

Mon indicator lights. Return to coded squelch by momentarily pressing Mon again.

To un-squelch the radio, press and hold Mon until a second "chirp" sounds. Ad ust

the volume with the Vol up/down rocker button. Momentarily press Mon again to

return to coded squelch operation.

• Carrier-Squelch Operation

Rotate the squelch-control knob to the fully counterclockwise position. When the

channel is clear, slowly rotate the squelch-control knob clockwise until the noise

stops. This is the threshold squelch setting. The operator may ad ust the squelch

knob to reduce interference when necessary.

Motorola

MaraTrac

Advanced Control Head

Operating Instructions

Scan:

Press the Scan button to turn scan on; a "chirp" sounds and the Scan indicator

lights (solid) indicating the system is scanning. Momentarily press Scan again to

Motorola

MaraTrac

Advanced Control Head

Operating Instructions

turn scan off. When on a preset internal scan list or an operator selectable scan list

the radio scans for activity. While scanning, if activity on the priority mode is

detected, the Pri indicator flashes. When activity is detected on a non-priority mode,

the Non-Pri indicator lights up solid.

Scan with talkback:

When talkback scan is enabled by programming, after activity has ceased, the radio

will suspend scan and stay on the same channel for the duration of receive talkback

hang-time. Priority sampling will continue. The Priority indicator/B SY indicator will

show priority information. Whenever the PTT button is released and the radio de-

keys, scan will be suspended and stay on the same channel for the duration of

transmit talkback hang-time. Priority sampling will continue. If the PTT button is

pressed while scan is suspended in hang-time, the radio will key up on the last

mode that had activity. Priority indicators will show priority information. The display

will show the channel that had activity. After the talkback hangtime is expired, the

radio will resume scan.

Edit ser's Scan List:

Press and hold the Scan button until a "chirp" sounds. The Scan indicator flashes to

indicate scan "configuration" mode. Use the Mode up/down rocker button or Rcl

(recall) to review the user's scan list. The Pri indicator flashes when the priority

mode has been selected or the Non-Pri indicator lights solid when a non-priority

mode has been selected. Use the Sel button to scroll from "not-in-the-list" to "non-

priority" to "priority" and back to "not-in-the-list". The effect each Sel button press

has on a selected mode's scan list is explained in the following table.

If Condition Is: One Sel Press Will: Indicators Change To:

Selected Mode NOT

in the List

Add Mode to the List as

Non-Priority

Non-Pri lights (Pri Off)

Selected Mode in List

as Non-Priority

Raise Mode's Status to

Priority *

Pri flashes (Non-Pri off)

Selected Mode in List

as Priority

Delete Mode from List Both lights off

* If another mode was previously designated as a priority mode, the previously

designated priority mode's status is lowered to non-priority when you exit the

configuration mode.

To exit the configuration mode and simultaneously save the scan list changes,

momentarily press the Scan or the Home button.

Home Mode:

Use the Home button to select the internally programmed Home mode and to exit

any configuration mode.

Motorola

MaraTrac

Advanced Control Head

Operating Instructions

Dimmer Button:

Pressing the DIMmer button once dims the display's brightness. Pressing the

DIMmer button a second time returns the display back to full brightness.

Standard Features Note:

PL Channel Scan

, talk-around, Quik-Call II

and Stat-Alert

decode features are

shipped from the factory disabled and require field programming. Refer to the

MaraTrac Radio Service Software and Radio Signaling Options manuals for

programming instructions.

Stat-Alert

and Quik-Call II

Operation Procedures:

• Call AlertTM

When a Call Alert is received, four beeps sound every five seconds and the armed

external alarms* will operate. The display flashes "CA". To clear the alarms, take the

microphone off-hook or press the Mon button. The display shows the current mode

number. If scan was on the display shows the priority mode. To reply to the Call

Alert, press the PTT button.

• Selective Call

When a Selective Call is received, the radio will beep twice. The display flashes

"SC". A voice message will follow.

Wait until the voice message is complete. The display stops flashing and shows the

current mode number. Pick up the microphone, press the PTT button and reply to

the Selective Call.

Telephone Interconnect:

Requires DTMF Microphone and DTMF Decoder Kit installed

When a phone call comes in, telephone-type ringing sounds and the armed external

alarms* will operate. The display flashes "PH".

To respond, pick up the DTMF microphone and enter the connect code (normally

the "*" button), press the PTT button, and speak into the microphone. To listen,

release the PTT button. Explain to the land-line caller that they must wait until you

release the PTT button (indicated by a soft beep) before they can speak.

When the call is complete, enter the disconnect code (normally the "#" button) and

hang up the microphone.

* External Alarms:

When the external alarms option is installed in a VHF or UHF MaraTrac radio, the

horn and lights can be activated by pressing the H/L button. To change this

Motorola

MaraTrac

Advanced Control Head

Operating Instructions

configuration, press and hold the H/L button until the radio enters the select mode (a

single "chirp" will sound). Use the Mode up/down rocker button to change the

desired horn and lights setting. Once the desired setting has been selected, press

the Home or H/L button to exit and return to normal operation. When a Call Alert is

received, the external alarms will respond with your selected alarm setting.

On a low band radio with ad ustable squelch, pressing the H/L button activates both

the horn and lights; they are not independently selectable.

Single Tone

Encode:

Requires Single Tone Kit installed

• To Select Single Tone:

To select Single Tone, momentarily press the ST button on the control head. The

radio sounds one beep and displays the selected tone for two seconds. The red

indicator under the ST button will light.

• To Send Single Tone:

Press the PTT button. The talk inhibit side-tone will be heard if it is programmed to

enable. The selected tone will be displayed for the duration of the tone if the display

tone on PTT is programmed to enable. Wait for the Single Tone to complete, then

speak normally in to the microphone.

• To Turn Off Single Tone:

To turn off Single Tone, momentarily press the ST button on the control head. The

radio will sound one beep and the red indicator light under the ST button will be off.

• To Enter Configuration Mode:

To enter the configuration mode, press and hold the ST button on the control head

until the radio beeps and the red indicator under the ST button flashes. The display

will show the selected tone. Use the Mode up/down button to scroll through the

available tones.

• To Select a Tone and Exit Configuration Mode:

Press the ST button, or the Home button, to exit configuration mode and to select

the Single Tone currently displayed.

NOTE

If Single Tone is selected, and you scroll to a non-Single Tone mode, the ST

indicator will be off until you reach a mode with Single Tone.

Andere Motorola Controller Handbücher

Motorola

Motorola MVME162P-344 Series Kurzanleitung

Motorola

Motorola RZ100 Bedienungsanleitung

Motorola

Motorola hmdc5025 Bedienungsanleitung

Motorola

Motorola MVME162P4 Series Leitfaden

Motorola

Motorola MVME162FX400 Series Bedienungsanleitung

Motorola

Motorola M68HC08 Bedienungsanleitung

Motorola

Motorola MBX Series Kurzanleitung

Motorola

Motorola 700 Series Kurzanleitung

Motorola

Motorola MC68HC908AB32 Gebrauchsanweisung

Motorola

Motorola RFS4011 Series Bedienungsanleitung

Motorola

Motorola HMGW1075 Bedienungsanleitung

Motorola

Motorola MVME172 Bedienungsanleitung

Motorola

Motorola DSP56F801 Gebrauchsanweisung

Motorola

Motorola MVME162FX Bedienungsanleitung

Motorola

Motorola MVME172P4 Series Kurzanleitung

Motorola

Motorola 3200 Bedienungsanleitung

Motorola

Motorola MVME162 Bedienungsanleitung

Motorola

Motorola MVME172P4 Series Bedienungsanleitung

Motorola

Motorola 56F800 Bedienungsanleitung

Motorola

Motorola iDEN Site Controller Benutzerhandbuch

Motorola

Motorola MC68824 Bedienungsanleitung

Motorola

Motorola MC68360 Bedienungsanleitung

Motorola

Motorola MVME162P2 Series Kurzanleitung

Motorola

Motorola MVME162LX 300 Series Kurzanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch