Motorola GP68 Bedienungsanleitung

ManualNumber:502-4501

23278 Bernhardt Street • Hayward, CA. 94545

Phone: (510) 887-1950 • Fax: (510) 887-4011

Internet: [email protected]

InstallationandOperation

Manual

SmarTrunk II

LogicBoard

for

MotorolaGP68

PortableRadios

SmarTrunk Systems, Inc. • ST-865M3

Motorola P/N PMLN4066A

Quality Policy Statement

SmarTrunk Systems, Inc., has a continuing objective to enhance our

worldwide reputation as a supplier of products and services which meet or

exceed customer requirements.

With personal commitment and pride in everything we do, all officers,

managers,andemployeeswillworktogetherforcontinuousimprovementin

theprocessesandprocedureswhichaffect SmarTrunk’sproductqualityand

customerservice.

SmarTrunkTM isaTrademarkofSmarTrunkSystems,Inc.

MotorolaManualNumber

68P04370J43

Warranty Policy

All SmarTrunk products are guaranteed to meet or exceed published

performance specifications and are warranted against defects in material

and workmanship for a period of two (2) years from date of purchase. Third

party equipment such as radios, power supplies, antennas, etc., carry the

factory warranty of their respective manufacturers.

All warranty repairs must be performed at the SmarTrunk factory in Hayward,

California, or other factory authorized repair depot. Any unauthorized repair

attempted by the customer, alteration or modification of the equipment, damage

by external sources, or removal or alteration of the serial number label or date

code, will void the warranty. Specifically excluded from this warranty are

batteries, fuses, lamps, and damage caused by lightning, power surges, or

mechanical abuse.

Equipment for repair may be returned to the factory without prior written

authorization; however, a note must be sent with the packing list briefly

describing the nature of the defect. Repairs must be shipped freight prepaid

and will be returned freight prepaid. Shipments should be directed to:

SmarTrunkSystems, Inc.

ATTN: Repair Department

23278 Bernhardt Street

Hayward, CA 94545, U.S.A.

CONTENTS

iii

5/1/96

INTRODUCTION ......................................... V I I

1  OPERATION .............................................. 1

1.1 Landline To Subscriber Call .................... 1

1.2 Receiving A Call ..................................... 2

1.3 Call Routing Codes For Subscriber

Initiated Calls ......................................... 2

1.3.1 Subscriber To Landline Call ................................ 3

1.3.2 Subscriber To Subscriber Call............................. 3

1.3.3 Fleet Dispatch (Subscriber) To Group Call ........ 3

1.3.4 Conventional Mode............................................... 3

1.3.5 Mobile Operator Call ........................................... 4

1.3.6 Emergency Call...................................................... 4

1.4 Originating A Call ................................... 4

1.4.1 Store And Send Dialing ........................................ 5

1.4.2 Memory Speed Dialing ......................................... 6

1.4.3 Programming Memory Speed Dial Numbers ...... 6

1.4.4 Redial ..................................................................... 7

1.4.5 Priority Call Override........................................... 7

1.4.6 Clear Channel Alerting......................................... 8

1.5 Call Termination ..................................... 8

1.6 Radio-Kill ............................................... 9

2  OPERATING MODES ............................... 11

2.1 Subscriber ID Numbers/Paging Code

Numbers ............................................... 11

2.2 Conventional ......................................... 14

3  INSTALLATION ........................................ 15

3.1 Disassemble Radio ................................ 15

3.1.1 Remove Battery ....................................................16

3.1.2 Remove Radio Chassis ........................................17

Model ST-865M3 SmarTrunk II™ Logic Board

3.2 Installation of the Logic Board ............... 18

3.3 Reassemble Radio ................................ 19

3.3.1 Replace Radio Chassis .......................................19

3.3.2 Replace Battery and Antenna ............................20

3.4 Trouble Shooting ................................... 21

3.5 Portable Radio Programming ................... 22

3.5.1 System Tone..........................................................22

4  LOGIC BOARD PROGRAMMING .............. 23

4.1 Entering The Program Mode ................... 23

4.2 Programming Feature Descriptions ........ 23

4.2.1 Number of Trunking Channels...........................24

4.2.2 Primary Code.......................................................26

4.2.3 Secondary Code ..................................................26

4.2.4 Priority Subscriber Enable.................................26

4.2.5 Five Digit Access Code .......................................27

4.2.6 Return To Radio Default Values.........................28

4.2.7 Trunking System ID Number ..............................28

4.2.8 Automatic PTT Mode...........................................29

4.2.9 Emergency Call Override ...................................29

4.2.10 Clear Channel Alerting Mode............................30

4.2.11 Radio-Kill .............................................................30

4.2.12 Memory Speed Dial Programming.....................30

4.2.13 Conventional Operating Mode ..........................31

CONTENTS

Tables

Table 1-1 • Call Routing Codes ........................................................ 3

Table1-2•Dialing Modes ................................................................ 5

Table2-1•ST-852MProgramming ............................................... 13

Table2-2•MobileProgramming .................................................... 14

Table4-1•Programming OptionsSummaryTable .......................... 25

Figures

Figure3-1• Slide Battery Latch...................................................... 16

Figure3-2•SlideBatteryCover..................................................... 16

Figure3-3• Remove Radio Chassis................................................ 17

Figure3-4•ExplodedView of Radio ............................................. 18

Figure3-5•ReplaceRadio'sChassis.............................................. 19

Figure3-6•Troubleshooting........................................................... 21

Appendixes

AppendixA•Programming Worksheet........................................... 33

Appendix B • Motorola P/N • HLN9247A & HLN3083A

SmarTrunkSystems,Inc.•ST-868M50

CrossReferenceChart ............................................ 35

Model ST-865M3 SmarTrunk II™ Logic Board

(This page left blank intentionally)

INTRODUCTION

vii

The ST-865M3 SmarTrunk II Logic Board is a microprocessor based

radio trunking logic board designed for use with Motorola GP68 Radio. The

ST-865M3 implements SmarTrunk II, an efficient radio channel allocation proto-

col. The SmarTrunk II Logic Board controls all radio functions including channel

scan, PTT, and all transmit and receive audio. In combination with the ST-852M

SmarTrunk II Digital Trunking Controller, the Logic Board provides a complete

multi-channel digital access radio trunking system.

The ST-852M is the heart of the SmarTrunk II system. Programming and opera-

tion is performed by the System Operator/Manager. Many of the programmable

features of the ST-865M3 require information unique to a specific system. These

system specifics can only be obtained from the System Operator/Manager.

In addition to SmarTrunk II trunking operation, the ST-865M3 has a conventional

operating mode. This mode allows the radio to operate as a conventional two way

radio on the programmed radio channels. Conventional mode can be disabled by

the dealer.

The ST-865M3 offers the user the following features:

• Store and send dialing

• 10 number memory speed dial (user programmable)

• Last number re-dial

• Different ringing tones to distinguish the type of call

• Clear channel alerting tells subscriber when a channel is available

• Ten levels of priority call override

• Two trunking modes: radiotelephone and fleet dispatch

• Capability of operation on SmarTrunk and conventional non-trunked

radio channels

• Automatic acknowledgment eliminates wasted airtime

• Five digit security code for dealer programming

• Remote Radio-Kill to disable illegal and non-paying customers

This manual is presented in four sections:

•Section 1, Operation, describes operational features.

•Section 2, Operating Modes, describes the operating modes available in

a SmarTrunk II system.

•Section 3, Installation, provides instructions for programming of radio

frequencies and installation of the ST-865M3 logic board.

•Section 4, Logic Board Programming, provides the installing technician

instructions to configure the ST-865M3 by programming the resident

EEPROM.

Please read the entire manual before proceeding in order to take advantage of all

the advanced features.

Model ST-865M3 SmarTrunk II™ Logic Board

viii

(This page left blank intentionally)

Subscribers already familiar with the original SmarTrunk system will find the

SmarTrunk II digital system just as easy to use. There are also many additional

features and enhancements. The ST-865M3 begins trunking operation as soon as

the radio is powered on. Channel selection, transmit control, receiver audio, and

other radio functions are all under the control of the ST-865M3. Radio channel

access is tightly controlled. Unauthorized transmission and monitoring of trunking

channels is not possible by SmarTrunk II equipped radios.

During keypad operation, the ST-865M3 provides audible alerts. These alerts

are:

a. Short chirp is generated each time a key is pressed.

b. High frequency beep indicating a successful keypad entry sequence.

c. Low frequency beep indicating that improper data has been entered.

d. Three long low frequency beeps indicating all channels are busy or im-

proper keypad operation.

e. DTMF tones during DTMF over-dialing.

1.1 Landline To Subscriber Call

When the ST-852M is called from a telephone system, it answers the

telephone line with two beeps. The caller then dials the subscriber ID

number of the subscriber or group that they are trying to call.

If the subscriber ID number is valid, the ST-852M attempts to reach the

subscriber over the air. If the subscriber ID number is for a radiotelephone

subscriber unit that is powered OFF or is out of the operating, area the

caller will hear a busy signal. If the subscriber unit is powered ON and is

inthe operating areathe caller willhear a ringback and theST-865M3 will

start ringing. The subscriber answers the call by pressing the asterisk key

(*)on the microphoneDTMF keypad (Push-To-Talk (PTT) is not pressed).

If the subscriber does not answer within the mobile answer time

(programmable), the caller will get a busy signal for a few seconds and

then the ST-852M will hang up. If the subscriber does answer, the caller

will hear two beeps and can then begin talking.

1 • OPERATION

Model ST-865M3 SmarTrunk II™ Logic Board

1.2 Receiving A Call

The subscriber is alerted to an incoming call by ringing of the subscriber

equipment. This alerting takes four forms, related to the type of incoming

call.

a. A long single high frequency ring is generated by the logic board,

then a low frequency dual tone ring is generated by the controller.

This indicates an incoming landline call.

b. A short double high frequency ring is generated by the logic board,

then a low frequency dual tone ring is generated by the controller.

This indicates an incoming call from another SmarTrunk II radio

subscriber.

c. A short single high frequency ring is generated by the logic board,

then a double beep is generated by the controller. This indicates a

manually dialed group call.

d. A short single high frequency ring is generated in the calling radios

logic board, then a double beep is generated by the controller. This

indicates a (PTT) dispatch group call.

For items a and b, the subscriber must press * on the DTMF keypad to

answer the incoming call (Push-to-talk (PTT) is not pressed). For items c

and d, the subscriber may communicate with other members of the group

by pressing PTT (no answer action is required).

1.3 Call Routing Codes For Subscriber Initiated

Calls

Call routing codes are used for initiating a call from a subscriber to the

appropriate destination. Call routing codes are commonplace in PBX

telephone systems. For example, to place a call to an outside telephone

line through a PBX, a call routing code of typically 0 or 9 must be dialed

first. The SmarTrunk II system operates in a similar fashion, however, the

call routing code is placed at the end of the calling sequence.

The following table describes all the call routing codes. The subscriber

needs to be familiar only with the call routing codes that apply to their

application.

Andere Handbücher für GP68

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Hauptplatine Handbücher

Motorola

Motorola ITMC9S12XDP512 Bedienungsanleitung

Motorola

Motorola MVME167 Series Bedienungsanleitung

Motorola

Motorola PPC/CPCI-690 Bedienungsanleitung

Motorola

Motorola CPCI-6020 Kurzanleitung

Motorola

Motorola MVME761-001 Kurzanleitung

Motorola

Motorola MVME6100 Kurzanleitung

Motorola

Motorola MVME167P Kurzanleitung

Motorola

Motorola MVME5100 Series Bedienungsanleitung

Motorola

Motorola MC145192EVK Bedienungsanleitung

Motorola

Motorola Digital DNA DSP56F807 Gebrauchsanweisung

Motorola

Motorola MPC564EVB Bedienungsanleitung

Motorola

Motorola MTX series Bedienungsanleitung

Motorola

Motorola M68EM05P18 Bedienungsanleitung

Motorola

Motorola MVME2700 Series Kurzanleitung

Motorola

Motorola M68360QUADS-040 Bedienungsanleitung

Motorola

Motorola MB68k-100 Bedienungsanleitung

Motorola

Motorola PATX3070 Series Kurzanleitung

Motorola

Motorola M5271EVB Bedienungsanleitung

Motorola

Motorola CPV5000 Installations- und Betriebsanleitung

Motorola

Motorola M68HC11EVBU Bedienungsanleitung

Motorola

Motorola MVME2600 Series Bedienungsanleitung

Motorola

Motorola DSP56F803 Gebrauchsanweisung

Motorola

Motorola Minimal PowerPC 603e Bedienungsanleitung

Motorola

Motorola MVME3100 Handbuch

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung