Motorola 68436 - Vanguard 100I - Remote Access Server Handbuch

Vanguard 100 PC Operator's Guide

Notice

1995 Motorola Inc.

20 Cabot Boulevard

Mansfield, Massachusetts 02048

(508) 261-4000

Printed in U.S.A.

Restricted Rights Notification for U.S. Government Users

The software (including firmware) addressed in this manual is provided to the

U.S. Government under agreement which grants the government the minimum

"restricted rights" in the software, as defined in the Federal Acquisition

Regulation (FAR) or the Defense Federal Acquisition Regulation Supplement

(DFARS), whichever is applicable.

If the software is procured for use by the Department of Defense, the following

legend applies:

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to restrictions as set

forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227-7013.

If the software is procured for use by any U.S. Government entity other than the

Department of Defense, the following notice applies:

Notice Notwithstanding any other lease or license agreement that may pertain to, or

accompany the delivery of, this computer software, the rights of the Government

regarding its use, reproduction, and disclosure as set forth in FAR 52.227-19(C).

Unpublished -rights reserved under the copyright laws of the United States.

Proprietary Material

Information and software in this document are proprietary to Motorola Inc. (or its

Suppliers) and without the express prior permission of an officer of Motorola Inc.,

may not be copied, reproduced, disclosed to others, published, or used, in whole

or in part, for any purpose other than that for which it is being made available.

Use of software described in this document is subject to the terms and conditions

of the Motorola Software License Agreement.

This document is for information purposes only and is subject to change without

notice.

Radio Frequency Interference Regulations

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules, CISPR 22 and EN 55022.

These limits are designed to provide reasonable protection against interference in

aresidential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician to help.

Changes or modifications not expressly approved by Motorola could void the

user's authority to operate the equipment.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

This product was FCC certified under test conditions that included use of shielded

data terminal equipment cables. Use of different cables will invalidate FCC

certification and increase the risk of causing interference to radio and TV

reception.

You can obtain the proper cables from Motorola.

Writer: Donna McLean

Project Editor: Susan L. Roswit

Publication Specialist: Denise Skinner

Illustrator: Tim Kinch

Part No.: 09974, Rev A

Publication Code: RC

First Printing: Oct. 1995

Manual is current for Release 4.50 of the 6500 Series Operating Software.

To comment on this manual, please send email to: [email protected] or use the

Customer Response Card located in this manual.

Internet Information

Additional company and product information can be found on our Internet Web

page at:

http://www.mot.com/MIMS/ISG/

About This Guide

Introduction

This manual describes installation and configuration of the Motorola Vanguard

100 PC Frame Relay Access Device (PC FRAD). This manual is intended for

persons who are installing and setting up the Motorola Vanguard 100 PC.

The Vanguard 100 PC provides all of the functionality of a Vanguard 100 Frame

Relay Access Device (FRAD), in a high-speed PC serial card that is installed in

your desktop PC.

Software Revision Level

The Vanguard 100 PC runs Release 4.50 or higher of Motorola 6500 Series

operating software.

Special Notices

The following notices emphasize certain information in the manual. Each serves a

special purpose and is displayed in the format shown:

IMPORTANT: Important is used to emphasize any significant procedural information.

Caution provides you with information that, if not followed, can result in

damage to software, hardware, or data.

Warning is the most serious notice, indicating that you can be physically hurt.

How To Use This Manual

Use the following table to help you find information in this manual on a particular

task or subject.

This section... Describes

Chapter 1 Audience definition, PC hardware and software

requirements, and an overview of Vanguard 100 PC features.

Chapter 2 Warnings and cautions, unpacking, DSU connection

information, COM port and interrupt settings, Vanguard 100

PC board settings, and placing the Vanguard in your PC.

Chapter 3 Optional DIM and Daughtercard hardware installation and

configuration.

Chapter 4 PC COM software configuration, accessing the Control Port

to manipulate the Vanguard 100 PC, and saving and

downloading configurations.

Chapter 5 Sample applications and configurations.

Appendix A Specifications, including power and environmental

requirements.

Appendix B Details of the sample configurations given in Chapter 5.

Related Documentation

The following documentation is not provided with the Motorola Vanguard 100

PC; it can be ordered separately. To acquire any of these sets of documentation,

refer to the following product codes:

Product Code Documentation Kit Includes:

17460 6500 Series Documentation

Kit The printed documentation

set including:

6500 Series Introduction

Manual (Part No. 09871,

Rev D)

6500 Series Configuration

and Administration Manual

(Part No. 09873, Rev D)

6500 Installation Manual

(Part No. 09872, Rev E)

6520 Installation Manual

(Part No. 09901, Rev C)

17461 Documentation Change

Notices Documentation for all

software releases since the

last printing of the main

documentation set.

17313 Multi-Product CD-ROM All 6500 Series

documentation and some

Vanguard user

documentation, as was

available at the time of

release.

6500 Series documentation is prepared using FrameMaker document publishing

software.

Additional Related Documentation

The following documents contain information related to the installation and

operation of 65xx and Vanguard platforms:

•The 6500 Series Options and Protocols Binder (Part No. 09950)

Vanguard Operator's Guides

•Vanguard 100 Operator's Guide (Part No. 09962, Rev A)

•Vanguard 200 Operator's Guide (Part No. 09968, Rev A)

•Vanguard 300/305 Operator's Guide (Part No. 09965, Rev B)

Software Download Guides

•6520 Software Download Guide (Part No. 09901-6, Rev A)

•6500 PLUS Software Download Guide (Part No. 09872-2, Rev A)

•Vanguard 100 Software Download Guide (Part No. 09962-2, Rev A)

•Vanguard 200 Software Download Guide (Part No. 09968-1, Rev A)

•Vanguard 300/305 Software Download Guide (Part No. 09965-1, Rev B)

Trademarks

The following are trademarks or registered trademarks of their respective

companies or organizations.

Crosstalk / Digital Communications Associates, Inc.

Pentium / Intel Corporation

ProComm / Datastorm Technologies, Inc.

About the Vanguard 100 PC

Overview

The Motorola Vanguard 100 PC is a multi-protocol Frame Relay Access Device

(FRAD) housed on a PC serial card. It installs in a 16-bit ISA or VESA slot in

your Personal Computer, and allows you to connect your PC to a Frame Relay,

X.25, or ISDN network, as shown in Figure 0-1.

Figure 0-1. The Motorola Vanguard 100 PC

The Vanguard 100 PC has all the functionality of a Vanguard 100, and uses the

same software images. However, the Vanguard 100 PC provides the following

benefits over the Vanguard 100:

•Built-in 16550 high-speed COM card

•Uses standard 16550 COM drivers and software packages

•Software upgrades are available for additional protocol support (via CD-

ROM or Internet Web Site)

•Plug-and-Play capability

•Port #1 daughtercards are available for DSU, DIM Site, and ISDN

•Port #2 on-board DIM is available to support V.11, V.24, V.35, or V.36

DIMs

•Eliminates the RS232 cable by internally connecting Port #3 to your PC

COM port

•Eliminates the need for an external Frame Relay device, power supply,

and configuration terminal

The Vanguard 100 PC appears to the PC and communications software as if it

were a 16550 high-speed COM card.

Intended Audience

This manual is intended for those who are installing and configuring the

Vanguard 100 PC. It assumes that you are familiar with installing cards in your

PC and have an understanding of communications software in general.

PC Hardware and Software Requirements

The following hardware and software must be available before you install your

Vanguard 100 PC:

•An IBM or IBM Compatible PC (286, 386, 486, or Pentium) with an

unobstructed full card ISA or VESA slot

•A commercial communications software package (i.e., ProComm)

•A Frame Relay, X.25, or ISDN connection supplied by your service

provider

Features

The Motorola Vanguard 100 PC is a FLASH-based mono FRAD or duo FRAD

available with an optional integral DSU, ISDN U or S/T, or DIM Site

daughtercard. An optional second port can be used for Dial Backup or as another

user port.

Vanguard 100 PC Software

The Vanguard 100 PC has all the functionality of a Vanguard 100. All Vanguard

100 software images from Release 4.50 and higher will run on a Vanguard 100

PC.

All Vanguard 100 PCs are shipped with the Release 4.50 Toronto software

option preinstalled. This software includes the following operating feature set:

Software option... ...includes these protocols

Toronto

Source Filename: 450c17.xrc

Version String: V4.50-Toronto-

V100

Description Filename: 450c17.des

•Async PAD, Transparent Polled Async

•Frame Relay Interface (FRI)

•ISDN D Packet, Leased Line

•Point to Point Protocol (PPP)

•Serial Line Internet Protocol (SLIP)

•Simple Network Management Protocol

(SNMP)

•Switched Internet Protocol (SW-IP)

•Trivial File Transfer Protocol (TFTP)

•X.25 DCE/DTE

DSU Functionality

The DSU daughtercard provides a 56 kbps point-to-point DDS1 interface that

conforms to AT&T 62310 or ANSI T1E1.4/91-006.

The DSU is FCC Part 68 registered.

Diagnostic loopbacks from the telephone company are supported; local

diagnostics are activated from the Control Terminal Port (CTP) of the Vanguard

itself. See Chapter 4, Software Configuration and Control Port Access, for

information about accessing the CTP.

Port Characteristics

Vanguard 100 PC is available in two and three serial port versions. Ports have the

following characteristics.

Port

Interface Connector Default Speed DTE/DCE

DSU: RJ48S Frame Relay 56 kbps (sync) N/A

ISDN U/ST RJ45 Frame Relay

128 kbps N/A

1Daughtercard

DIM Site: DB25 Frame Relay

V.24:

-?80 kbps (sync)

-?115.2 kbps (async)

V.35, V.11, or V.36:

-?384 kbps int. clock

-?1.54 Mbps ext. clock

Selectable

2DIM on

motherboard DB25 Frame Relay

V.24:

-?80 kbps (sync)

-?115.2 kbps (async)

V.35, V.11, or V.36:

-?384 kbps int. clock

-?1.54 Mbps ext. clock

Selectable

3Motherboard Internal Async ?115.2 kbps (async) N/A

The default node configuration is PPP on Port #3, and Frame Relay Bypass on

Ports #1 and #2. The PVC connection is to Port #1, if a daughtercard is installed,

or Port #2 if there is no optional daughtercard.

Note: To return the node to the default settings (default the node), you must do

the following:

Step

Action

1 Power up the PC with the Vanguard 100 PC installed and wait 1 minute

for the node to initialize.

2 Enable the Default Node switch.

3 Press the reset button and allow the Vanguard 100 PC to reboot. Wait 1

minute for the node to initialize.

4 Disable the Default Node switch. The Node default is complete.

Memory

The board contains 1 Mbyte of FLASH memory and 2 Mbytes of DRAM.

Note: Memory is not upgradeable on a Vanguard 100 PC.

For More Information

For additional information, refer to the "Related Documentation" section in About

This Guide.

Standard Hardware Installation

Overview

This chapter describes how to unpack your Motorola Vanguard 100 PC, order

your DSU connection, and install, test, and monitor the Vanguard 100 PC. If you

are installing any optional hardware components (DIMs or daughtercards), also

refer to the procedures in Chapter 3, Optional Hardware Installation.

Warnings and Cautions

The following special notices apply to all equipment handling procedures in this

operator's guide.

Motorola Vanguard 100 PC daughtercards and DIMs are sensitive to static

discharge, which can damage components. You must use proper handling and

grounding precautions when handling a Motorola Vanguard 100 PC

daughtercard or DIM.

Ports capable of connecting to ports on other apparatus are defined as Safety

Extra Low Voltage (SELV). To conform with EN60950, ensure that these

ports are only connected to ports of the same type on other apparatus.

Les ports qui sont susceptibles d'être connectés a des équipements sont

désignés comme TBTS. Pour garantir la conformité à la norme EN 60950,

n'interconnecte ces ports qu'avec des ports du même type sur des autres

matériels.

Anschlusse, die mit anderen Geraten verbindet werden konnen, sind als SELV

beschrieben. Um Konformitat mit EN 60950 zu versichern, sichern Sie es, daß

diese Anschlusse nur mit den des selben Type auf anderen Geraten verbindet

werden.

Lightning Protection

All Motorola Vanguard devices should be used in environments designed for

computers and electronic equipment. In areas susceptible to lightning, take

precautions to prevent damage to electronic equipment. Contact your telephone

company, or an electronic accessories vendor, for information on lightning

protection equipment.

Andere Handbücher für 68436 - Vanguard 100I - Remote Access Server

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Netzwerk-Hardware Handbücher

Motorola

Motorola W24 Handbuch

Motorola

Motorola MOTOwi4 Canopy 30 Bedienungsanleitung

Motorola

Motorola Dimetra KVL 4000 Air Bedienungsanleitung

Motorola

Motorola DSP96002ADM Bedienungsanleitung

Motorola

Motorola Vonage VT2142 Bedienungsanleitung

Motorola

Motorola AP-7131 Series Bedienungsanleitung

Motorola

Motorola DSR-4410MD Handbuch

Motorola

Motorola 2.1 Bedienungsanleitung

Motorola

Motorola Avigilon 3 Series Bedienungsanleitung

Motorola

Motorola vap2400 Bedienungsanleitung

Motorola

Motorola WS200 Bedienungsanleitung

Motorola

Motorola Canopy Powerline MU Bedienungsanleitung

Motorola

Motorola PTP 400 Series Bedienungsanleitung

Motorola

Motorola CPEi 725 Bedienungsanleitung

Motorola

Motorola PTP 500 Bedienungsanleitung

Motorola

Motorola PMP 58430 Bedienungsanleitung

Motorola

Motorola Avigilon HD-NVR4-PRM-64TB Bedienungsanleitung

Motorola

Motorola Starline SG 2000 Bedienungsanleitung

Motorola

Motorola M68ICS08RK Bedienungsanleitung

Motorola

Motorola CB3000 - Client Bridge - Wireless Access... Bedienungsanleitung

Motorola

Motorola VAP2404 Bedienungsanleitung

Motorola

Motorola NE 1000 Bedienungsanleitung

Motorola

Motorola MOTOMESH DUO 4300 Bedienungsanleitung

Motorola

Motorola Avigilon ACC VMA-RPA-RGD-8P2 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung