Motorola 68230 - Vanguard 300 DSU/CSU Handbuch

Vanguard 300/305 Operator's Guide

Notice

1995 Motorola Inc.

20 Cabot Boulevard

Mansfield, Massachusetts 02048

(508) 261-4000

Printed in U.S.A.

Restricted Rights Notification for U.S. Government Users

The software (including firmware) addressed in this manual is provided to the

U.S. Government under agreement which grants the government the minimum

"restricted rights" in the software, as defined in the Federal Acquisition

Regulation (FAR) or the Defense Federal Acquisition Regulation Supplement

(DFARS), whichever is applicable.

If the software is procured for use by the Department of Defense, the following

legend applies:

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to restrictions as set

forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer

Software clause at DFARS 252.227-7013.

If the software is procured for use by any U.S. Government entity other than the

Department of Defense, the following notice applies:

Notice Notwithstanding any other lease or license agreement that may pertain to, or

accompany the delivery of, this computer software, the rights of the Government

regarding its use, reproduction, and disclosure as set forth in FAR 52.227-19(C).

Unpublished -rights reserved under the copyright laws of the United States.

Proprietary Material

Information and software in this document are proprietary to Motorola Inc. (or its

Suppliers) and without the express prior permission of an officer of Motorola Inc.,

may not be copied, reproduced, disclosed to others, published, or used, in whole

or in part, for any purpose other than that for which it is being made available.

Use of software described in this document is subject to the terms and conditions

of the Motorola Software License Agreement.

This document is for information purposes only and is subject to change without

notice.

Vanguard 300/305 Radio Frequency Interference Regulations

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules, CISPR 22 and EN 55022.

These limits are designed to provide reasonable protection against interference in

a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician to help.

Changes or modifications not expressly approved by Motorola could void the

user's authority to operate the equipment.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

This product was FCC certified under test conditions that included use of shielded

data terminal equipment cables. Use of different cables will invalidate FCC

certification and increase the risk of causing interference to radio and TV

reception.

You can obtain the proper cables from Motorola.

Writer: Donna McLean

Project Editor: Susan L. Roswit

Publication Specialist: Paul Tavares

Illustrator: Tim Kinch

Part No.: 09965, Rev B

Publication Code: RC

First Printing: Aug. 1995

Manual is current for Release 4.50 of the Vanguard 300 operating software, and

Release 4.49 of the Vanguard 305 operating software.

To comment on this manual, please send email to: [email protected] or use the

Customer Response Card located in this manual.

Internet Information

Additional company and product information can be found on our Internet Web

page at:

http://www.mot.com/MIMS/ISG/

About ThisManual

Introduction

This manual describes features, hardware, specifications, and applications for the

Motorola Vanguard 300 and Vanguard 305 Frame Relay Access Devices

(FRADs).

For information on operating system software and configuration see the 6500

Series Documentation Kit, which includes the 6500 Series Introduction Manual

and the 6500 Series Configuration and Administration Manual.

Audience

This manual is intended for operators of the Motorola Vanguard 300/305 FRAD.

Software Revision Level

The Vanguard 300 runs Release 4.33 or higher releases of operating software. The

Vanguard 305 runs Release 4.49 or higher.

Special Notices

The following notices emphasize certain information in the manual. Each serves a

special purpose and is displayed in the format shown:

IMPORTANT: Important is used to emphasize any significant procedural information.

Caution provides you with information that, if not followed, can result in

damage to software, hardware, or data.

Warning is the most serious notice, indicating that you can be physically hurt.

How to Use This Manual

The following table describes the contents of this guide.

This chapter... Describes

Chapter 1 Vanguard 300/305 hardware and software features, and FCC

Part 68 guidelines and Telephone Company procedures.

Chapter 2 Setting up a Vanguard 300/305, including site preparation,

how to unpack the unit, installationprocedures, powerup and

diagnostic procedures, and how to connect to the Control

Terminal Port

Chapter 3 Vanguard 300/305 applications and configuration

information, including step-by-step configuration sequences

Chapter 4 Maintaining the Vanguard 300/305, including replacing

option cards and troubleshooting information

Related Documentation

The following documentation is not provided with the Motorola Vanguard

300/305; it can be ordered separately. You should familiarize yourself with the

6500 Series documentation before you use the Vanguard Series.

To acquire any of these sets of documentation, refer to the following product

codes:

Product Code Documentation Kit Includes:

17460 6500 Series Documentation

Kit The printed documentation

set including:

6500 Series Introduction

Manual (Part No. 09871,

Rev D)

6500 Series Configuration

and Administration Manual

(Part No. 09873, Rev D)

6500 Installation Manual

(Part No. 09872, Rev E)

6520 Installation Manual

(Part No. 09901, Rev C)

17461 Documentation Change

Notices Documentation for all

software releases since the

last printing of the main

documentation set.

17313 Multi-Product CD-ROM All 6500 Series

documentation and some

Vanguard user

documentation, as was

available at the time of

release.

6500 Series documentation is prepared using FrameMaker document publishing

software.

Additional Related Documentation

The following documents contain information related to the installation and

operation of 65xx and Vanguard platforms:

•The 6500 Series Options and Protocols Binder (Part No. 09950)

Vanguard Operator's Guides

•Vanguard 100 Operator's Guide (Part No. 09962, Rev A)

•Vanguard 200 Operator's Guide (Part No. 09968, Rev A)

•Vanguard 300/305 Operator's Guide (Part No. 09965, Rev B)

Software Download Guides

•6520 Software Download Guide (Part No. 09901-6, Rev A)

•6500 PLUS Software Download Guide (Part No. 09872-2, Rev A)

•Vanguard 100 Software Download Guide (Part No. 09962-2, Rev A)

•Vanguard 200 Software Download Guide (Part No. 09968-1, Rev A)

•Vanguard 300/305 Software Download Guide (Part No. 09965-1, Rev B)

Trademarks

The following are trademarks or registered trademarks of their respective

companies or organizations.

DECconnect Digital Equipment Corporation

About the Vanguard 300/305

Overview

The Vanguard 300/305

The Motorola Vanguard 300/305 Frame Relay Access Device (FRAD) provides

serial devices with LAN Ethernet (Vanguard 300) or Token Ring (Vanguard 305)

access into public or private Frame Relay networks.

The FLASH-based Vanguard 300/305 is available in FRAD, mono FRAD, or duo

FRAD configurations with either two or three serial ports and an abundant list of

protocol choices. You can order the base unit with an integral DSU and a software

application package, making this low-cost FRAD an economical choice for

connecting remote LAN sites with both LAN and Serial traffic to public Frame

Relay services.

You can also configure extra serial ports on the mono and duo FRAD to provide a

backup link to the Frame Relay network port. Or, you can connect them to an

external analog dial modem, SW56 DSU or ISDN BRI TA, to provide an

alternate path in case of network failure.

Example of the Vanguard 300/305

The Vanguard 300/305 is available either with or without an integral DSU

daughtercard or DIM Site daughtercard in a desktop-size standalone enclosure, as

shown in Figure 1-1.

Figure 1-1. The Vanguard 300 and Vanguard 305

Features

Introduction

This section describes Vanguard 300/305 hardware configurations and standard

features.

Configurations Options

The Vanguard 300/305 is available in the following hardware configurations.

This configuration: Offers...

300 Ethernet FRAD Ethernet port, V.24 port, CTP port.

300 Ethernet FRAD with

DSU Ethernet port, DSU daughtercard in Port 1, CTP

port.

300 Ethernet mono

FRAD Ethernet port, serial port with a choice of DIM port

interface (V.24, V.35, V.36, or V.11) in Port 2, CTP

port.

300 Ethernet mono

FRAD with DSU Ethernet port, V.24 port, DSU daughtercard in Port

1, CTP port.

300 Ethernet duo FRAD Ethernet port, V.24 port, DIM Site daughtercard in

Port 1 with choice of DIM port interface (V.24,

V.35, V.36, or V.11), CTP port.

300 Ethernet duo FRAD

with DSU Ethernet port, V.24 port, DSU daughtercard in Port

1, serial port with a choice of DIM port interface

(V.24, V.35, V.36, or V.11) in Port 2, CTP port.

305 Token Ring FRAD Token Ring port, V.24 port, CTP port.

305 Token Ring FRAD

with DSU Token Ring port, DSU daughtercard in Port 1, CTP

port.

305 Token Ring mono

FRAD Token Ring port, serial port with a choice of DIM

port interface (V.24, V.35, V.36, or V.11) in Port 2,

CTP port.

305 Token Ring mono

FRAD with DSU Token Ring port, V.24 port, DSU daughtercard in

Port 1, CTP port.

305 Token Ring duo

FRAD Token Ring port, V.24 port, DIM Site daughtercard

in Port 1 with a choice of DIM port interface (V.24,

V.35, V.36, or V.11), CTP port.

305 Token Ring duo

FRAD with DSU Token Ring port, V.24 port, DSU daughtercard in

Port 1, serial port with a choice of DIM port

interface (V.24, V.35, V.36, or V.11) in Port 2, CTP

port.

Standard Features

The Vanguard 300/305 features 1, 2, or 3 port Serial FRAD functionality with

LAN access to Frame Relay networks.

All Vanguard 300/305 base units provide the following:

•Control Terminal Port (CTP) for configuration and management

•Dual link ability

•Optional DSU

•Optional ISDN Daughtercards

•Ethernet (Vanguard 300) or Token Ring (Vanguard 305) interface

•Frame Relay and X.25 service

•X.25 PAD support

•Multiprotocol support

•SNMP management

•Software download through Trivial File Transfer Protocol (TFTP)

•Fully compatible with 6500 PLUS and 6520.

•RFC 877 encapsulation

CTP Port

Port 3 on the Vanguard 300/305 can be used as a CTP for configuration,

reporting, and troubleshooting. You candefault Port 3 for CTP access from the

front panel of the Vanguard. See "Connecting to the CTP" in Chapter 2 for more

details.

DSU Functionality

The DSU daughtercard functionality suits an extended range of 56 kbps point-to-

point DDS1 interface that conforms to AT&T 62310 or ANSI T1E1.4/91-006.

The DSU is FCC Part 68 registered.

Diagnostic loopbacks from the telephone company are supported; local

diagnostics are activated from the CTP.

LAN Support

The Vanguard 300 features an onboard Ethernet interface that supports both

10BaseT and AUI. The factory default is AUI.

The Vanguard 305 features an onboard Token Ring interface. Support includes:

•4 and 16 Mbps support

•Type 1 STP (DB-9)

•Type 3 UTP (RJ-45)

Frame Relay & X.25 Service

The Vanguard 300/305 provides serial devices with economical LAN access into

public or private Frame Relay WAN networks via Ethernet or Token Ring.

Because the Vanguard 300/305 also supports X.25, you can configure it as a PAD

if Frame Relay is not an immediate need. When Frame Relay service becomes

available, you can reconfigure the Vanguard 300/305 as a FRAD.

Multiprotocol Support

Support includes SDLC, Bisync, X.25, Async, IP/IPX, and Routing and Bridging,

as well as many other serialprotocols.

Software Download

Trivial File Transfer Protocol (TFTP) provides software downloading for network

software and device configurationsoftware.

RFC 877

RFC 877 encapsulation of IP datagrams over an X.25 network allows for

interoperability of Front End Processors (FEPs) that support X.25 and IP traffic as

well as router vendors supporting RFC 877/1356.

Sample Applications

Figure 1-2 shows sample applications for the Vanguard 300/305.

Figure 1-2. Vanguard 300/305 Sample Applications

Hardware

Introduction

This section describes the Vanguard 300/305 hardware components.

See the Software Release Notice (SRN) accompanying your Vanguard product for

details on hardware platformbundles currently available.

Components

Vanguard 300/305 base units include the following components:

•A motherboard

•A power supply

•One V.24 port with DB25 connector

•Optional port for daughtercard (DIM Site or DSU)

•Optional DIM port on the motherboard

•One LAN port:

§Vanguard 300: Ethernet with either 10BaseT or AUI interface

§Vanguard 305: Token Ring with connectors for both shielded

(STP) and unshielded

•(UTP) cables

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Motorola Netzwerk-Router Handbücher

Motorola

Motorola CPEI 885 Series Bedienungsanleitung

Motorola

Motorola WR850GP - Wireless Broadband Router Bedienungsanleitung

Motorola

Motorola 2108-N9 Bedienungsanleitung

Motorola

Motorola MD1600 Bedienungsanleitung

Motorola

Motorola EX-3524 Bedienungsanleitung

Motorola

Motorola Netopia R910 Bedienungsanleitung

Motorola

Motorola WE800G - Wireless EN Bridge Bedienungsanleitung

Motorola

Motorola WE800G - Wireless EN Bridge Bedienungsanleitung

Motorola

Motorola POWERBROADBAND 45101 Bedienungsanleitung

Motorola

Motorola MT7711 Bedienungsanleitung

Motorola

Motorola WR850 Bedienungsanleitung

Motorola

Motorola 68390 - Vanguard 320 Router Bedienungsanleitung

Motorola

Motorola Netopia R910 Bedienungsanleitung

Motorola

Motorola MotoWI4 PTP 600 Series Bedienungsanleitung

Motorola

Motorola 68384 - Vanguard 320 Router Bedienungsanleitung

Motorola

Motorola EWR6300 Bedienungsanleitung

Motorola

Motorola PTP 300 Series Bedienungsanleitung

Motorola

Motorola PMP 320 Bedienungsanleitung

Motorola

Motorola 68390 - Vanguard 320 Router Bedienungsanleitung

Motorola

Motorola RFS6000 - Wireless RF Switch Bedienungsanleitung

Motorola

Motorola BSR 2000 Programmierhandbuch

Motorola

Motorola MR1700 Bedienungsanleitung

Motorola

Motorola PTP 300 Series Bedienungsanleitung

Motorola

Motorola SURFboard SBG941 Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung