Motorola AP-8132 Bedienungsanleitung

AP-8132 Access Point

INSTALLATION GUIDE

2 AP-8132 Access Point

Installation Guide 3

1.0 Introduction ...............................................4

1.1 Document Conventions ........................................4

1.2 Warnings ...................................................5

1.3 Site Preparation .............................................5

1.4 AP-8132 Package Contents .....................................5

2.0 Hardware Installation .......................................7

2.1 Installation Instructions ........................................7

2.2 Precautions..................................................7

2.3 Access Point Placement........................................7

2.4 Power Injector System.........................................8

2.5 Wall Mount Installation.......................................10

2.6 Suspended Ceiling T-Bar Mount Installation.......................12

2.7 Suspended Ceiling Tile (Plenum) Installation ......................14

2.8 AP-8132 Antenna Options .....................................17

2.9 LED Indicators ..............................................19

3.0 Basic Access Point Configuration ...........................21

4.0 Specifications.............................................38

4.1 Electrical Specifications.......................................38

4.2 Physical Specifications .......................................38

4.3 Radio Specifications .........................................39

5.0 Regulatory Information .....................................40

6.0 Part Numbers, Support, and Sales ...........................48

7.0 Motorola Solutions, Inc. End-User License Agreement .........49

8.0 AP-8132 Access Point China ROHS Compliance ...............52

4 AP-8132 Access Point

1 Introduction

The AP-8132 is a premium, Enterprise class, access point positioned at the top of Motorola Solutions’ access

point product line. The AP-8132 is a plenum rated, 3x3:3 802.11n access point utilizing two 802.11abgn radios.

An AP-8132 model access point uses WiNG 5 software as its onboard operating system. The access point’s unique

WiNG 5 software enables the access point to function as either a Virtual Controller AP capable of adopting and

managing up to 24 additional AP-8132 access points, a Standalone access point or a Dependent mode access

point managed by its connected controller.

If new to Motorola Solutions access point technology, refer to the WiNG Access Point System Reference Guide to

familiarize yourself with access point technology and the feature set supported by the WiNG operating system.

The guide is available, at http://supportcentral.motorola.com/support/product/manuals.do.

This document is written for the qualified network device installer.

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

Installation Guide 5

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before

connecting the AP-8132 model access point.

• Remove jewelry and watches before installing this equipment.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment

operation specifications.

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, power

drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.

1.4 AP-8132 Package Contents

An AP-8132 access point is available in external antenna models only. An AP-8132 ships with the following:

• AP-8132 access point

• AP-8132 Installation Guide (This Guide)

• Wall mount screw and anchor kit

• Accessories bag (LED light pipe for above the ceiling installations)

NOTE An AP-8132 access point can ship with a separately ordered protective

cover (facade) containing a 6-element MIMO antenna (Part No.

ML-2452-PTA6M6-1). When attached, LEDs continue to illuminate

through the cover (similar to the illustration on the next page). A version

of the facade is also available without the MIMO antenna. This cover

(Part No. 21-8132FAC-01) functions strictly as a protective cover for the

access point and provides no operational functionality.

6 AP-8132 Access Point

1.4.1 Features

An AP-8132 access point minimally supports the following feature set:

• 3 RJ-45 connectors (GE1/POE, GE2 and Console)

• LED indicators

• Slots for wall mounting

• Lock port for Kensington® style security lock

• Two custom dual band radios

• Features for snap-on module support through the access point’s USB interface

• 3x3 MIMO, 3 spatial streams

The AP-8132 access point has two RJ-45 connectors supporting 10/100/1000 Ethernet. GE1/POE accepts 802.3at

or 802.3af compliant power from an external source

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

Installation Guide 7

2 Hardware Installation

2.1 Installation Instructions

An AP-8132 access point mounts either on a wall (with M4 x 25 pan head screws and wall anchor - or equivalent)

or on a suspended ceiling T-bar.

Once the AP-8132 is installed with facade and cabled, the cables (Ethernet and module connections) should not be

visible when looking directly at the unit (ceiling and wall mounts).

To prepare for the installation:

1. Match the model number on the purchase order with the model numbers in the packing list and on the

case of the access point.

2. Verify the contents of the box include the intended AP-8132 access point, and the included hardware

matches the package contents on page 4.

3. Review site survey and network analysis reports to determine the location and mounting position for the

AP-8132 access point.

4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3at or 802.3af power source and run the

cable to the installation site. Ensure there is sufficient slack on the cable to perform the installation

steps.

2.2 Precautions

Before installing an AP-8132 model Access Point, verify the following:

• Your using the correctly rated power solution for the AP-8132 (either the AP-PSBIAS-2P3-ATR power

injector or the PWRS-14000-247R external power supply)

• Motorola Solutions recommends you do not to install the AP-8132 in wet or dusty areas.

• Verify the environment has a continuous temperature range between 0° C to 50° C.

2.3 Access Point Placement

For optimal performance, install the access point away from transformers, heavy-duty motors, fluorescent lights,

microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls

Part Number Description

AP-8132-66040-US 802.11n 3x3:3 access point dual radio US version

AP-8132-66040-WR 802.11n 3x3:3 access point dual radio non-US (rest of world) version

AP-8132-66040-EU 802.11n 3x3:3 access point dual radio European version

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

8 AP-8132 Access Point

or floors block transmission. Install the access point in an open area or add access points as needed to improve

coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An

area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even

placement of a light bulb) provides even, efficient coverage.

Place the access point using the following guidelines:

• Install the access point at an ideal height of 10 feet from the ground.

• Orient the access point antennas vertically for best reception (applies to external antenna models only).

To maximize the access point’s radio coverage area, Motorola Solutions recommends conducting a site survey to

define and document radio interference obstacles before installing the access point.

2.4 Power Injector System

An AP-8132 model access point can receive power via an Ethernet cable connected to the GE1/POE (LAN) port.

When users purchase a WLAN solution, they often need to place access points in obscure locations. In the past, a

dedicated power source was required for each access point in addition to the Ethernet infrastructure. This often

required an electrical contractor to install power drops at each access point location. The Power Injector merges

power and Ethernet into one cable, reducing the burden of installation and allowing optimal access point

placement in respect to the intended coverage area.

The AP-8132’s supported Power Injector (Part No. AP-PSBIAS-2P3-ATR) is a high power POE Injector delivering up

to 30 watts. The access point can only use a Power Injector when connecting the unit to the access point’s GE1/POE

port. The Power Injector is separately ordered and not shipped with an existing AP SKU.

The Motorola access point Power Supply (Part No. PWRS-14000-247R) is not included with the access point and is

orderable separately as an accessory. If the access point is provided both POE power and PWRS-14000-247R power

concurrently, the access point will source power from the PWRS-14000-247R supply only. Disconnecting AC power

from the PWRS-14000-247R, causes the access point to re-boot before sourcing power from the POE power

injector. If the AP is operating using injector supplied power, the AP will not automatically reboot if an AC adapter

is connected. The access point continues to operate with power supplied from the AC adapter without change to

the access point operating configuration. If using AC adapter supplied power and a change to the AP’s operating

configuration is warranted, the access point needs to be manually rebooted by the customer.

CAUTION Using a non-compliant injector, or an injector supporting legacy modes

will not allow the AP-8132 to function at optimum performance levels.

CAUTION Do not plug in the AP-PSBIAS-2P3-ATR Power Injector into the access

point’s Console port. Connecting the Power Injector into the console

port can damage the port and void the AP-8132’s product warranty.

Installation Guide 9

A separate Power Injector is required for each AP-8132 access point comprising the network.

The Power Injector can be installed free standing, on an even horizontal surface or wall mounted using the power

injector’s wall mounting key holes. The following guidelines should be adhered to before cabling the Power Injector

to an Ethernet source and an access point:

• Do not block or cover airflow to the Power Injector.

• Keep the Power Injector away from excessive heat, humidity, vibration and dust.

• The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance,

ensure the Power Injector is placed as close as possible to the data port.

CAUTION The access point supports any standards-based compliant power

source (including non-Motorola Solutions power sources). However,

using the wrong solution (including a POE system used on a legacy

Motorola Solutions access point) could either limit functionality or

severely damage the access point and void the product warranty.

10 AP-8132 Access Point

To install the Power Injector to an Ethernet data source and an access point:

1. Connect the Power Injector to an AC outlet (110VAC to 220VAC).

2. Connect an RJ-45 Ethernet cable between the network data supply (host) and the Power Injector Data In

connector.

3. Connect an RJ-45 Ethernet cable between the Power Injector Data & Power Out connector and the

access point’s GE1/POE port.

Ensure the cable length from the Ethernet source (host) to the Power Injector and access point does not

exceed 100 meters (333 ft).

The Power Injector has no On/Off power switch. The Injector receives power and is ready for device

connection and operation as soon as AC power is applied. Refer to the Installation Guide shipped with the

Power Injector for a description of the device’s LEDs.

2.5 Wall Mount Instructions

A wall mount deployment requires hanging the AP-8132 access point along its width or length using two of three

slots on the bottom of the unit. The AP-8132 can be mounted on to any plaster, wood or cement wall surface using

the provided wall anchors.

The hardware required to install the AP-8132 on a wall consists of:

• Two wide-shoulder Phillips pan head self-tapping screws (M3.5 x 0.6 x 23 mm)

• Two wall anchors

• Security cable (optional)

Optional customer provided installation tools include:

• Security cable

• Philips head screw driver, or drill and drill bit

CAUTION To avoid problematic performance and restarts, disable POE from a

wired switch port connected to an access point if mid-span power

sourcing equipment (PSE) is used between the two, regardless of the

manufacturer of the switch.

CAUTION Ensure AC power is supplied to the Power Injector using an AC cable

with an appropriate ground connection approved for the country of

operation.

CAUTION Cabling a Power Injector to the WAN port (GE2 port) renders the AP

non-operational. Only use a AP-PSBIAS-2P3-ATR Power Injector with

the access point’s GE1/POE (LAN) port.

Andere Handbücher für AP-8132

Inhaltsverzeichnis

Andere Motorola Drahtloser Zugangspunkt Handbücher

Motorola

Motorola PMP 320 Bedienungsanleitung

Motorola

Motorola AP-8132 Bedienungsanleitung

Motorola

Motorola AP-6521 Series Bedienungsanleitung

Motorola

Motorola AP-7522 Bedienungsanleitung

Motorola

Motorola AP-7131 Series Installations- und Betriebshandbuch

Motorola

Motorola AP 6522M Bedienungsanleitung

Motorola

Motorola AP6562 Bedienungsanleitung

Motorola

Motorola AP6522 Bedienungsanleitung

Motorola

Motorola WA840GV2 Bedienungsanleitung

Motorola

Motorola PMP 100 Bedienungsanleitung

Motorola

Motorola AP-6521E Bedienungsanleitung

Motorola

Motorola WS2000 - Wireless Switch - Network Management... Bedienungsanleitung

Motorola

Motorola AP-51XX Installations- und Betriebshandbuch

Motorola

Motorola MOTOMESH Duo 4300-49 Bedienungsanleitung

Motorola

Motorola WA840G Bedienungsanleitung

Motorola

Motorola 5440AP - Canopy 5.4 GHz AP Betriebsanleitung

Motorola

Motorola AP-7131 Series Bedienungsanleitung

Motorola

Motorola WiNG 5.4.2 Bedienungsanleitung

Motorola

Motorola AP 7181 Bedienungsanleitung

Motorola

Motorola Verizon VAP2500 Bedienungsanleitung

Motorola

Motorola AP-7131 Series Installations- und Betriebshandbuch

Motorola

Motorola AP-6511 Bedienungsanleitung

Motorola

Motorola AP-7131N-FGR Bedienungsanleitung

Motorola

Motorola AP-7131 Series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung