— 4 — — 5 — — 6 —
Push Buttons
There are four push buttons on the DA-661/662/663’s front panel. The
buttons are used to enter text onto the LCD screen. The buttons are
MENU, (up cursor), (down cursor), and SEL:
Button Action
MENU Displays the main menu
Scrolls up through a list of items shown on the LCD
screen’s second line
Scrolls down through a list of items shown on the LCD
screen’s second line
SEL Selects the option listed on the LCD screen
Real-time Clock
The DA-661/662/663’s real-time clock is powered by a lithium battery.
We strongly recommend that you do not replace the lithium battery
without help from a qualified Moxa support engineer. If you need to
change the battery, contact the Moxa RMA service team.
ATTENTION
There is a risk of explosion if the battery is replaced by an incorrect type.
6. Powering on Your DA-661/662/663
To power on the DA-661/662/663, connect the power line to the
DA-661/662/663’s AC/DC power connector (located on the right side
of the rear panel) with the power cord that is shipped with the product,
and then turn on the power switch. It takes about 30 seconds for the
system to boot up. Once the system is ready, the Ready LED on the
front panel will light up, and the DA-661/662/663 will display the
model name and firmware version on the LCD screen.
7. Connecting to the DA-661/662/663 from a PC
There are two ways to connect to the DA-661/662/663 from a PC:
through the serial console port or by Telnet over the network. The
COM settings for the serial console port are: Baudrate = 115200 bps,
Parity = None, Data bits = 8, Stop bits = 1, Flow Control = None.
ATTENTION
Remember to choose the “VT100” terminal type. Use the
CBL-RJ45F9-150 cable included with the product to connect a PC to the
DA-661/662/663’s serial console port.
When using Telnet, you need to know the DA-661/662/663’s IP address
and netmask. The default LAN settings are shown below. For first-time
configuration, you may find it convenient to use a cross-over Ethernet
cable to connect directly from the PC to the DA-661/662. Please use a
Fiber-to-Ethernet converter to connect to the DA-663.
Default IPAddress Netmask
LAN 1 (FX1) 192.168.3.127 255.255.255.0
LAN 2 (FX2) 192.168.4.127 255.255.255.0
LAN 3 192.168.5.127 255.255.255.0
LAN 4 192.168.6.127 255.255.255.0
Once the DA-661/662/663 is powered on, the Ready LED will light up,
and a login page will open. Use the following default Login name and
Password to proceed.
Login: root
Password: root
8. Configuring the Ethernet Interface
If you use the console cable for first-time configuration of the Network
settings, use the following commands to edit the interfaces file:
# ifdown –a
//DisableLAN1/LAN2interfacefirst,beforeyoureconfigure
the LAN settings. LAN 1 = eth0, LAN 2= eth1//
# vi /etc/network/interfaces
//check the LAN interface first//
After the boot settings of the LAN interface have been modified, use
the following commands to activate the LAN settings immediately:
# sync ; ifup –a
9. Developing YourApplication
dnategratnorewoP xuniLCPottcennoc
margorP ?deggubeD
ssorcUNGllatsnI xuniLCPnorelipmoc cbilGllatsnI xuniLCPno CPnotneilcBDGllatsnI )lanoitpo(xuniL
margorpedoC elipmoC& ottegratotdaolnwoD tsetdnanur
resu-dnepoleveD noitacilppa
relipmocssorcputeS tnemnorivnecbilGdna selbairav
seY
oN
weN margorP
10. Installing the DA-661/662/663 Tool Chain
The PC must have the Linux Operating System pre-installed to install
the DA-661/662/663 GNU Tool Chain. Redhat 7.3/8.0/9.0 Fedora Core
1/2/3/4/5 are recommended. The Tool Chain will use about 900 MB of
your PC’s hard disk space. Use the following command to install the
Tool Chain from the DA-661/662/663 CD:
# mount –t iso9660 /dev/cdrom /mnt/cdrom
# cp /mnt/cdrom/tool-chain/linux/install.sh /tmp/
# sh /tmp/install.sh
The Tool Chain will be installed on your PC automatically.
11. Compiling and Running Hello.c
The path to the Tool Chain is:
# export PATH=”/user/local/xscale_be/bin”:$PATH
The DA-661/662/663 Software CD also includes several example
programs. Here we use Hello.c as an example to show you how to
compile and run your applications. Type the following commands on
your PC:
# cd /tmp/
# mkdir example
# cp –r /mnt/cdrom/example/* /tmp/example
Next, go to the Hello subdirectory and type the following command:
# make
to finish compiling Hello.c.
Finally, run the executable file that was created to generate
hello-release and hello-debug.
NOTE: Moxa also provides the Windows Tool Chain for
DA-661/662/663. The Windows Tool Chain simulates a Linux
environment on a Windows operating system, allowing you to develop
programs for DA-661/662/663 on a Windows platform. The
DA-661/662/663 User’s Manual contains complete details on how to
install the Windows Tool Chain.
12. Environmental Specifications
Power requirements 100 to 240 VAC auto ranging
(47 to 63 Hz for AC input)
Dimensions (W×D×H) 480 × 198 × 45 mm (including rack-mount ears)
440 × 198 × 45 mm (without rack-mount ears)
Operating temperature -10 to 60°C (14 to 140°F), 5 to 95% RH
Storage temperature -20 to 80°C (-4 to 176°F), 5 to 95%
Serial protection 15 KV ESD for serial port
Magnetic isolation 1.5 KV for Ethernet
Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV
Warranty 5 years
Click here for online support:
www.moxa.com/support
The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)
Europe: +49-89-3 70 03 99-0
Asia-Pacific: +886-2-8919-1230
China: +86-21-5258-9955 (toll-free: 800-820-5036)
©2008 Moxa Inc., All rights reserved.
Reproduction without permission is prohibited.
