Moxa Technologies NPort 5230 Bedienungsanleitung

– 1 – – 2 – – 3 –

P/N: 1802052000311

NPort 5200 Series

Quick Installation Guide

Seventh Edition, September 2014

Overview

The NPort 5200 compact palm-sized device servers are used to

control RS-232 (NPort 5210/5230/5210-T/5230-T) or RS-422/485

(NPort 5230/5232/5232I/5230-T/5232-T/5232I-T) serial devices

over a TCP/IP-based Ethernet.

NOTE

“

-T” indicates an extended operating temperature model.

Package Checklist

Before installing your NPort 5200, verify that the package contains

the following items:

1 NPort 5200 2-port Serial Device Server

Documentation & Software CD

NPort 5200 Series Quick Installation Guide

Optional Accessories

DK-35A: DIN-Rail Mounting Kit (35 mm)

CBL-RJ45M9-150: RJ45 (8-pin) to DB9 (M) cable, 150 cm

CBL-RJ45F9-150: RJ45 (8-pin) to DB9 (F) cable, 150 cm

CBL-RJ45M25-150: RJ45 (8-pin) to DB25 (M) cable, 150 cm

CBL-RJ45F25-150: RJ45 (8-pin) to DB25 (F) cable, 150 cm

DIN-Rail Power Supply and Adapter

Note: Notify your sales representative if any of the above items are

missing or damaged.

Hardware Introduction

The NPort 5200 device servers are used to control

RS-232/422/485 devices. The NPort 5210/5210-T has two 8-pin

RJ45 ports, both for the RS-232 interface. The NPort 5230/5230-T

has one 10-pin terminal block, with 5 pins used for one RS-232

port, and 5 pins used for one RS-422/485 port. The NPort

5232/5232I/5232-T/5232I-T have one 10-pin terminal block, with

5 pins used for one RS-422/485 port, and 5 pins used for another

RS-422/485 port.

Reset Button—Press the Reset button continuously for 5 sec to

load factory defaults: Use a pointed object, such as a straightened

paper clip or toothpick, to press the reset button. This will cause

the Ready LED to blink on and off. The factory defaults will be

loaded once the Ready LED stops blinking (after about 5 seconds).

At this point, you should release the reset button.

NPort 5200 LED Indicators (top panel)

LED

Name

LED

Color

LED Function

Ready red Steady on: Power is on and the NPort 5200 is

booting up.

Blinking: Indicates an IP conflict, or DHCP or

BOOTP server did not respond

properly.

green Steady on: Power is on and the NPort 5200 is

functioning normally.

Blinking: The device server has been located

by Administrator’s Location

function

off Power is off, or power error condition exists.

Ethernet orange 10 Mbps Ethernet connection.

green 100 Mbps Ethernet connection.

off Ethernet cable is disconnected, or has a short.

P1, P2 orange Serial port is receiving data.

green Serial port is transmitting data.

off No data is being transmitted or received

through the serial port.

Hardware Installation Procedure

STEP 1: After removing the NPort 5200 from the box, the first

thing you should do is connect the power adapter. Connect the

12-30 VDC power line with the NPort 5200’s terminal block, or

connect the DIN-rail power supply with the NPort 5200’s terminal

block.

STEP 2: Connect the NPort 5200 to a network. Use a standard

straight-through Ethernet cable to connect to a hub or switch.

When setting up or testing the NPort 5200, you might find it

convenient to connect directly to your computer’s Ethernet port. In

this case, use a cross-over Ethernet cable.

STEP 3: Connect the NPort 5200’s serial port to a serial device.

STEP 4: Placement Options

In addition to placing the

NPort 5200 on a desktop

or other horizontal

surface, you may also

make use of the DIN-rail

or wall mount options, as

illustrated here.

Wall Mount

DIN-Rail

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)

Europe: +49-89-3 70 03 99-0

Asia-Pacific: +886-2-8919-1230

China: +86-21-5258-9955 (toll-free: 800-820-5036)

Software Installation Information

To install NPort Administration Suite, insert the NPort

Document & Software CD into your computer’s CD-ROM drive.

Once the NPort Installation CD window opens, click on the

Installation button, and then follow the instructions on the screen.

To view detailed information about NPort 5200 Administration

Suite, click on the Documents button, and then select “NPort

5200 Series User’s Guide” to open the pdf version of this user’s

guide. The PComm Lite program is also included in the

Documentation & Software CD free of charge. Install PComm

Lite to use the Serial Console for configuring the IP address for

the first time.

Pin Assignments and Cable Wiring—

NPort 5230/5230-T

Terminal Block Wiring

NOTE The NPort 5232/5232I/5232-T/5232I-T have 2

RS-422/485 ports. The pin assignments are the same as

the NPort 5230/5230-T’s port 2. Refer to the “NPort 5200

Series User’s Manual” for more details.

Pin Assignments and Cable Wiring—

NPort 5210/5210-T

RJ45 (8-pin) Connector Pinouts

8-Pin Signal

1 DSR

2 RTS

3 GND

4 TxD

5 RxD

6 DCD

7 CTS

8 DTR

Cable Wiring (RS-232)

Four cables are available as optional accessories to connect the

NPort 5210/5210-T to RS-232 serial devices. For your convenience,

we show precise cable wiring diagrams for each of the four cables.

RJ45 (8-pin) to DB25 Female (Cable Name: CBL-RJ45F25-150)

RJ45 (8-pin) to DB25 Male (Cable Name: CBL-RJ45M25-150)

RJ45 (8-pin) to DB9 Female (Cable Name: CBL-RJ45F9-150)

RJ45 (8-pin) to DB9 Male (Cable Name: CBL-RJ45M9-150)

Specifications

Power Requirements

NPort 5210/5210-T: 12 to 48 VDC, 325 mA at 12V (max.)

NPort 5230/5230-T: 12 to 48 VDC, 325 mA at 12V (max.)

NPort 5232/5232-T: 12 to 48 VDC, 280 mA at 12V (max.)

NPort 5232I/5232I-T: 12 to 48 VDC, 365 mA at 12 V (max.)

Operating Temp.

Standard models: 0 to  (32 to 131F)

T models: -40 to 7 (-40 to 167F)

Operating humidity: 5 to 95% RH

Dimensions

NPort 5210/5230/5232/ 5210-T/5230-T/5232-T (including ears):

90 × 100.4 × 22 mm (3.54 × 3.95 × 0.87 in)

NPort 5210/5230/5232/ 5210-T/5230-T/5232-T (without ears):

67 × 100.4 × 22 mm (2.64 × 3.95 × 0.87 in)

NPort 5232I/5232I-T (including ears):

90 × 100.4 × 35 mm (3.54 × 3.95 ×1.37 in)

NPort 5232I/5232I-T (without ears):

67 × 100.4 × 35 mm (2.64 × 3.95 × 1.37 in)

Regulatory Approvals

EMI EN55022 Class A, FCC part 15 Subpart B Class A

EMS EN 61000-4-2 ESD: contact 4 kV; air 8 kV

EN 61000-4-3 RS: 3 V/m (80MHz to 1 GHz)

EN 61000-4-4 EFT: Power 1 kV; Signal 0.5 kV

EN 61000-4-5 Surge: AC 1 kV

EN 61000-4-6 CS: 3 V

EN 61000-4-8

EN 61000-4-11

Safety UL 60950-1, EN 60950-1

EMC 55022/24

Marine DNV

Medical (NPort 5210 only) EN 60601-1-2 Class B, EN55011

Dieses Handbuch passt für folgende Modelle

Andere Moxa Technologies Server Handbücher

Moxa Technologies

Moxa Technologies NPort 5250AI-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort S9000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Express DE-211 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5610-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA5000A-I/O series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2250A Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2150 Plus Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2610 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies 6150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5610-16 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 6150 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 6450 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2600 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5610-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA5000A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2250A-T-EU Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA5150A Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik E1210 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2600 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies CN2500 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ioLogik R2140 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung