Moxa Technologies NPort IA5000 Series Bedienungsanleitung

P/N: 1802051500216

*1802051500216*

NPort IA5150/5250 Series

Quick Installation Guide

Version 6.3, January 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

NPort IA device servers deliver easy and reliable serial-to-Ethernet

connectivity for the industrial automation market. The servers support

several operation modes—TCP Server, TCP Client, UDP, Real COM, Pair

Connection, and Ethernet Modem—ensuring the compatibility of network

software, and they are an ideal choice for connecting RS-232/422/485

serial devices, such as PLCs, sensors, meters, motors, drives, barcode

readers, and operator displays. NPort IA device servers come with a

compact and rugged DIN-rail mountable casing.

Package Checklist

Before installing NPort IA device servers, verify that the package contains

the following items:

•1 NPort IA Series device server

•NPort IA Series quick installation guide

Optional Accessories

•DR-4524: 5W/2A DIN-rail 24 VDC power supply with universal 85 to

264 VAC input

•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal

85 to 264 VAC input

•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to 132

VAC/176 to 264 VAC input by switch

Note: Notify your sales representative if any of the above items are

missing or damaged.

NPort IA5150 Series Appearance

- 3 -

NPort IA5250 Appearance

Reset Button—Press the Reset button for 5 seconds to load factory

defaults. Use a pointed object, such as a straightened paper clip or

toothpick, to press the reset button. This will cause the Ready LED to blink

on and off. The factory defaults will be loaded once the Ready LED stops

blinking (after about 5 seconds). At this point, you should release the

reset button.

NPort IA LED Indicators (front panel)

Name

Color

Function

PWR1,PWR2

Red

Power is being supplied to power input PWR1,

PWR2.

Ready

Red

Steady on: Power is on, and the NPort IA is

booting up.

Blinking: Indicates an IP conflict, the DHCP or

BOOTP server did not respond properly

, or a relay

output occurred.

Green

Steady on: Power is on, and the NPort IA is

functioning normally.

Blinking: The device server has been located by

the Administrator’s Location function.

Off

Power is off, or a power-error condition exists.

Ethernet

Orange

10 Mbps Ethernet connection.

Green

100 Mbps Ethernet connection.

Off

Ethernet cable is disconnected, or has a short.

P1, P2

Orange

Serial port is receiving data.

Green

Serial port is transmitting data.

Off

No data is being transmitted or received through

the serial port.

FX Orange

Steady on: Ethernet fiber connection, but port is

idle.

Blinking: Fiber port is transmitting or receiving

data.

- 4 -

Hardware Installation Procedure

STEP 1: After removing the NPort IA from the box, the first thing you

should do is connect the power adapter. Connect the 12-48 VDC power

line with the NPort IA’s terminal block, or connect the DIN-rail power

supply with the NPort IA’s terminal block.

STEP 2: Connect the NPort IA to a network. Use a standard

straight-through Ethernet cable to connect to a hub or switch. When

setting up or testing the NPort IA, you might find it convenient to connect

directly to your computer’s Ethernet port. In this case, use a crossover

Ethernet cable.

STEP 3: Connect the NPort IA’s serial port to a serial device.

STEP 4: The NPort IA is designed to be attached to a DIN rail or mounted

on a wall. The two sliders on the NPort IA’s rear panel serve a dual

purpose. For wall mounting, both sliders should be extended. For DIN-rail

mounting, start with one slider pushed in, and the other slider extended.

After attaching the NPort IA on the DIN rail, push the extended slider in to

lock the device server to the rail. The two placement options are

illustrated in the accompanying figures.

Wallmount DIN Rail

Software Installation Information

For the NPort’s configuration, the default IP address of the NPort is: LAN:

Static; IP = 192.168.127.254; netmask = 255.255.255.0.

NOTE

If you have forgotten the NPort's IP address, use the Device

Search Utility (DSU) from your PC to locate the NPort. After

searching the LAN for NPort units, the DSU will display the IP

address of each unit.

You may log in with the password moxa to change any setting to meet

your network topology (e.g., IP address) or serial device (e.g., serial

parameters). For first-time use, click the Wizard in the left navigation

panel. The wizard will prompt you to configure the IP address, SSID, and

security mode. For other settings, use the factory defaults or modify the

settings for your application.

For software installation, download the relative utilities from Moxa's

website:

- 5 -

https://www.moxa.com/support/support_home.aspx?isSearchShow=1

•Download the NPort Windows Driver Manager and install it as the

driver to run with Real COM mode of the NPort Series.

•Execute NPort Windows Driver Manager; then map the virtual COM

ports on your Windows platform.

•You may refer to the DB9 Male Ports pin assignment section to loop

back pin 2 and pin 3 for the RS-232 interface to carry out a self test on

the device.

•Use HyperTerminal or a similar program (you may download Moxa's

program, called PComm Lite) to test whether the device is good or

not.

Pin Assignments and Cable Wiring

RS-232/422/485 (Male DB9) Pinouts

RS-232

RS-422/RS-485 (4W)

RS-485 (2W)

DCD

TxD-(A)

–

RXD

TxD+(B)

–

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

4W/2W RS-485/RS-422 (Terminal Block) Pinouts

PIN RS-485 (2W)

RS-422/

RS-485 (4W)

–

TxD+(B)

–

TxD-(A)

Data+(B)

RxD+(B)

Data-(A)

RxD-(A)

–

GND

Four cables are available as optional accessories that can be used to

connect the NPort IA to RS-232 serial devices. For your convenience, we

show precise cable wiring diagrams for each of the two cables.

- 6 -

Female DB9 to Male DB9

Female DB9 to Male DB25

ATEX and IECEx Information

1. Certificate number: DEMKO 07 ATEX 0690059x

2. Ambient range (-40°C ≤ Tamb ≤ 75°C)

3. Certification string (Ex nA IIC T3)

4. Standards covered (EN60079-0:2006, EN60079-15:2005, IECEx UL

13.0023X, IEC 60079-0 Ed. 6, IEC 60079-15 Ed. 4)

5. Conditions of safe usage:

The Ethernet Communication Devices are to be mounted in an IP54

enclosure and used in an area with a pollution degree of not more

than 2, as defined by IEC 60664-1.

A 4-mm2conductor must be used when a connection to the external

grounding screw is utilized.

Conductors suitable for use in an ambient temperature of 114°C must

be used for the Power Supply Terminal.

Provisions shall be made, either in the apparatus or external to the

apparatus, to prevent the rated voltage to exceed the transient

disturbance by more than 40%.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Server Handbücher

Moxa Technologies

Moxa Technologies MiiNePort E1-SDK Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5250A Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 6150 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Express DE-211 Handbuch

Moxa Technologies

Moxa Technologies NPort IA5000A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5200A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5200 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies AirWorks AWK-1127 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Express DE-211 Handbuch

Moxa Technologies

Moxa Technologies NPort 5200 Serie Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort IA5150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 2310 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Server Lite DE-302 Handbuch

Moxa Technologies

Moxa Technologies NPort S8000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 6150 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5150AI-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2150Plus Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort W2004 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5610-16/8 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung