Moxa Technologies EtherDevice EDS-P506E-4PoE Series Bedienungsanleitung

P/N: 1802005060020

*1802005060020*

EDS-P506E-4PoE Series

Quick Installation Guide

Moxa EtherDevice™ Switch

Edition 1.0, February 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Package Checklist

The EDS-P506E-4PoE is shipped with the following items. If any of these

items are missing or damaged, please contact your customer service

representative for assistance.

•EDS-P506E-4PoE Ethernet switch

•USB cable

•Protective caps for unused ports

•Documentation

•Quick installation guide (printed)

•Warranty card

Features

•Up to 4 10/100BaseT(X) ports and 2 10/100/1000BaseT(X) or

100/1000BaseSFP ports

•Up to 4 IEEE 802.3af, IEEE 802.3at PoE+ standard, and 4-pair PoE

60W ports

36-watt output per PoE+ port in 2 pair PoE high power mode

60-watt output per PoE+ port in 4 pair PoE high power mode

Intelligent PoE power management functions

•Operate with 180 watts full PoE+ loading at -40 to 75°C

•Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250

switches), RSTP/STP, and MSTP for network redundancy

•TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance

network security

•Easy network management by web browser, CLI, USB serial console,

ABC-02-USB, MXview, MXconfig, and Windows utility

Default Settings

•Default IP address: 192.168.127.253

•Default Subnet Mask: 255.255.255.0

•Default Usernames: admin, user

•Default Password: moxa

- 3 -

Panel Views of EDS-P506E-4PoE Series

Front Panel

100BaseT(X) LED indicator

10BaseT(X) LED indicator

10/100 60W PoE+ Ports

Port 1 to 4

System status LED:

•STATE LED indicator

•PWR1 LED indicator

•PWR2 LED indicator

•FAULT LED indicator

•MSTR/HEAD LED indicator

•CPLR/TAIL LED indicator

USB storage port

G1 and G2 port LED indicator

Combo 10/100/1000BaseT(X) or

100/1000BaseSFP slot

Model Name

SmartPoE LED indicator of PoE+ ports

Top Panel

Reset button

USB console port

DIP switches for Turbo Ring, Ring

Master, and Ring Coupler

Grounding screw

4-pin terminal block for digital input

and power input 2

4-pin terminal block for relay output

and power input 1

Rear Panel

Screw holes for wall mounting kit

DIN-rail mounting kit

- 4 -

Mounting Dimensions

Unit = mm (inch)

- 5 -

DIN-Rail Mounting

The metal DIN-rail kit is fixed to the back panel of the EDS-P506E-4PoE

Series when you take it out of the box. Mount the EDS-P506E-4PoE Series

on corrosion-free mounting rails that meet the EN 60715 standard.

Installation

STEP 1—Insert the upper lip

of the DIN r

ail into the DIN-r

ail

mounting kit.

STEP 2

—Press the

EDS

-P506E-4PoE Series

towards the

DIN rail until it

snaps into place.

Removal

STEP 1—Pull down the latch

on the mounting kit

with a

screwdriver.

STEP 2

& 3—Slightly pull

the

EDS

-P506E-4PoE Series

forward and lift up to remove

it from the DIN r

ail.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the

EDS-P506E-4PoE Series on a wall (in an enclosure or industrial panel), as

shown in the following illustrations:

STEP 1—

Remove the

aluminum DIN rail attachment

plate from the rear panel

the

EDS-P506E-4PoE Series,

and then attach the wall

mount plates

with M3 screws

as shown

in the figure at the

right.

- 6 -

STEP 2—Mounting the EDS-P506E-4PoE Series on the

wall requires 4 screws. Use the

EDS-P506E-4PoE

eries

, with wall mount plates attached, as a guide to

mark the correct locations of the 4 screws. The heads

of the screws should be less than 6.0 mm in diameter,

and the shafts should be less than 3.5

mm in diameter,

as shown in the figure on at right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw through

one of the keyhole-shaped apertures of the Wall Mounting Plates.

Do not screw the screws in all the way—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3—Once the screws are fixed

the wall, insert the four screw

heads through the wide parts of the

keyhole

shaped apertures, and then

slide

the EDS-P506E-4PoE

downwards, as indicated

in the

figure

at the right. Tighten the four

screws for

more stability.

ATTENTION

The product should

be mounted in an

Industrial Control Panel and

the ambient temperature should not exceed 75°C.

Wiring Requirements

WARNING

Do not disconnect modules or wires unless power has been

switched off or the area is known to be non

-hazardous. The

devices may only be connected to the supply voltage shown on

the type plate. The devices are designed for operation with a

afety Extra-Low V

oltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

afety Extra-Low Voltages (SELV) in compliance with IEC950/

EN60950/ VDE0805.

ATTENTION

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply w

ith fire enclosure regulation IEC 60950/EN60950 (or

similar regulation).

- 7 -

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Please read and follow these guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together

•You should separate input wiring from output wiring

•We advise that you label the wiring to all devices in the system.

Grounding the Moxa EDS-P506E-4PoE Series

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Wiring the Relay Contact

The EDS-P506E-4PoE Series has one set of relay output. This relay

contact uses two contacts of the terminal block on the EDS-P506E-4PoE’s

top panel. Refer to the next section for detailed instructions on how to

connect the wires to the terminal block connector, and how to attach the

terminal block connector to the terminal block receptor. In this section,

we illustrate the meaning of the two contacts used to connect the relay

contact.

FAULT:

The two contacts of the 6

-pin terminal

block connector are used to detect

user

-configured events. The two wires

attached to the

fault contacts form an

open circuit when a user

-configured

event is triggered. If a user

-configured

event does not occur, the

fault circuit

remains closed.

- 8 -

Wiring the Redundant Power Inputs (12/24/48

VDC)

The EDS-P506E-4PoE Series has two sets of power inputs—power input 1

and power input 2. The top and front views of one of the terminal block

connectors are shown here.

STEP 1: Insert the negative/positive DC

wires into the V

-/V+ terminals,

respectively.

STEP 2:

To keep the DC wires from

pulling loose, use a small

flat-blade

screwdriver to tighten the wire

-clamp

screws on the front of the terminal block

connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on

the

EDS-P506E-4PoE’s top panel.

ATTENTION

Please use a power supply defined by SELV or one that complies

with the double insulation under the UL 60950, UL 61010

1, UL

61010-2-201 standards.

Wiring the Digital Inputs

The EDS-P506E-4PoE Series has one set of digital input (DI). The DI

consists of two contacts of the 4-pin terminal block connector on the

EDS-P506E-4PoE 's top panel, which are used for the two DC inputs. The

top and front views of one of the terminal block connectors are shown

here.

STEP 1: Insert the negative

(ground)/positive DI wires into the

┴

/I terminals, respectively.

STEP 2:

To keep the DI wires from

pulling loose, use a small flat

-blade

screwdriver to tighten the wire

-clamp

screws on the front of the terminal block

connector.

STEP 3:

nsert the plastic terminal block

connector prongs into the terminal block

receptor, which is located on

the

EDS-P506E-4PoE’s top panel.

Suggested Wire Type for Wiring Relay Contact (R), Digital

Input (DI) and Power Inputs (P1/P2)

The switch includes two 4-pins 5 mm pin-pitch terminal blocks. When

wiring the relay contact (R), digital input (DI) and power inputs (P1/P2),

we suggest using the cable type - AWG (American Wire Gauge) 12-28 and

the corresponding pin type cable terminals.

- 9 -

NOTE

The wire must be able to withstand at least 105°C and the torque

value should be 4.5 lb

-in (0.51 N-m). D

o not use excessive force

when fixing the wiring.

Communication Connections

Each EDS-P506E-4PoE series switch has 4 types of communication ports:

•1 USB console port (type B connector)

•1 USB storage port (type A connector)

•4 10/100 60W PoE+ Ethernet ports

•2 100/1000Base SFP slots

•2 10/100/1000BaseT(X) Ethernet ports

USB Console Connection

The EDS-P506E-4PoE Series has one USB console port (type B connector),

located on the top panel. Use the USB cable (provided in the product

package) to connect the EDS-P506E-4PoE's console port to your PC's USB

port and install the USB driver (available in the software CD) on the PC.

You may then use a console terminal program, such as Moxa PComm

Terminal Emulator, to access the EDS-P506E-4PoE’s console

configuration utility.

USB Console Port (Type B Connector) Pinouts

Description

D– (Data -)

VCC (+5V)

D+ (Data+)

GND (Ground)

USB Storage Connection

The EDS-P506E-4PoE Series has one USB storage port (type A connector)

on the front panel. Use Moxa ABC-02-USB-T automatic backup

configurator to connect the EDS-P506E-4PoE's USB storage port for

configuration backup, firmware upgrade or system log file backup.

ABC-02-USB Installation

Plug the ABC-02-USB into the

USB

storage port of

the Moxa

EDS

-P506E-4PoE Series.

Securing the ABC

-02-USB on

the wall with an M4 screw is

suggested.

- 10 -

USB Storage Port (Type A Connector) Pinouts

Description

VCC (+5V)

D– (Data -)

D+ (Data+)

GND (Ground)

10/100BaseT(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

1000BaseT Ethernet Port Connection

1000BaseT data is transmitted on differential TRD+/- signal pairs over

copper wires.

MDI/MDI-X Port Pinouts

Signal

TRD(0)+

TRD(0)-

TRD(1)+

TRD(2)+

TRD(2)-

TRD(1)-

TRD(3)+

TRD(3)-

PoE Ethernet Port Connection

PoE ports located on the EDS switch’s front panel are used to connect to

PoE-enabled devices. The pinout follows the Alternative A mode of

802.3af/802.3at standards and 4-Pair 60W mode. Details are shown

below.

PoE Port Pinouts for 802.3af/802.3at Mode

Power

V+

V-

PoE Port Pinouts for 4-Pair PoE 60W Mode

Power

V+

V-

V+

V-

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies EDS-208 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-510E Series Handbuch

Moxa Technologies

Moxa Technologies SDS-3016 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ToughNet Switch TN-5500 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ETHERDEVICE EDS-305 Handbuch

Moxa Technologies

Moxa Technologies PT-7728 Series Handbuch

Moxa Technologies

Moxa Technologies ICS-G7526 Series Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-G4500 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7710 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort S8458 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A-T Handbuch

Moxa Technologies

Moxa Technologies TN-4516A non-PoE series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G308 Handbuch

Moxa Technologies

Moxa Technologies EDS-600 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7828 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies SPL-24 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-P206A-4PoE-SS-SC Handbuch

Moxa Technologies

Moxa Technologies EDS-726 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-G205-1GTXSFP Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-2016-ML Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies S9450I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IEX-408E-2VDSL2 series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung