Moxa Technologies PT-G503-PHR-PTP Series Bedienungsanleitung

P/N: 1802005030011

*1802005030011*

PT-G503-PHR-PTP Series

Quick Installation Guide

Moxa Managed PRP/HSR Redundancy Box

Edition 2.0, April 2017

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The PT-G503-PHR-PTP series redundancy boxes (RedBoxes) are

compliant with the latest standardized redundancy protocols for industrial

automation networks, IEC 62439-3 Clause 4 (Parallel Redundancy

Protocol, PRP) and IEC 62439-3 Clause 5 (High availability Seamless

Redundancy, HSR). PRP/HSR ensures the highest system availability and

data integrity for mission-critical applications in electrical substation

and/or process automation systems that require zero recovery time

redundancy. The redundant protocols Coupling and QuadBox are also

supported. The PT-G503-PHR-PTP series comes with three

10/100/1000BaseT(X) and 100/1000BaseSFP slot combo ports. One slot

(INTERLINK port) is for an internal link for connecting with a SAN (Singly

Attached Node). The other two ports (LAN A and LAN B ports) are for

PRP/HSR redundant protocol communications. With this full Gigabit

Ethernet port design, the PT-G503-PHR-PTP series provides high

performance for PRP/HSR systems. The PT-G503-PHR-PTP series also

provides hardware-based IEEE 1588v2 PTP when in end-to-end one-step

transparent clock mode for timing-critical applications and isolated dual

power inputs with 24/48 VDC or 110/220 VDC/VAC power supply ranges

to increase the reliability of the power supply.

Package Checklist

The Moxa PT-G503-PHR-PTP series products are shipped with the

following items. If any of these items are missing or damaged, please

contact your customer service representative for assistance.

•1 PT-G503-PHR-PTP redundancy box

•DIN-rail kit

•Protective caps for SFP ports

•USB cable

•Quick installation guide (printed)

•Documentation and software CD

•Warranty card

- 3 -

Panel Layout

1. Power input PWR1/PWR2 LED

2. State LED / Fault LED

3. PRP/HSR/QUADBOX/COUPLING

LED

4. A/B port LED

5. Ethernet console port LED

6. INTERLINK port LED

7. 10/100/1000BaseT(X) A/B port

and interlink port or

100/1000BaseSFP slot combo

ports

8. 10/100/1000BaseT(X) Ethernet

console port

9. Model name

10.

Terminal block for power input

(PWR1, PWR2)

11.

Reset button

12.

Screw hole for grounding cable

13.

USB console port

14.

USB storage port (ABC-02-USB-T)

15.

Terminal block for power input

16.

Terminal block for DI and Relay 1

17.

Screw hole for wall mounting kit

18.

DIN-rail kit

- 4 -

Mounting Dimensions (unit = mm (inch))

DIN-Rail Mounting

The metal DIN-rail kit is fixed to the back panel of the PT-G503-PHR-PTP

when you take it out of the box. Mount the PT-G503-PHR-PTP on

corrosion-free mounting rails that meet the EN 60715 standard.

- 5 -

Installation

STEP 1:

Insert the upper lip of the DIN

-rail

into the DIN

-rail mounting kit.

STEP 2

Press the PT

-G503-PHR-

PTP towards

the DIN

rail until it snaps into place.

Removal

STEP 1:

Pull down the latch on the mounting

kit with a screwdriver

STEP 2

& 3:

Slightly pull the PT

-G503-PHR-PTP

forward and lift up to remove it from

the DIN

-rail.

Wall Mounting (optional)

For some applications, you will find it convenient to mount the

PT-G503-PHR-PTP on the wall, as shown in the following figures.

STEP 1:

Remove the aluminum DIN-rail attachment plate from the

PT-G503-PHR-PTP rear panel, and then attach the wall mount plates as

shown in the diagram below.

- 6 -

STEP 2:

Mounting

the PT-G503-PHR-PTP to a wall requires 6

screws. Use the PT

-G503-PHR-PTP, with wall mount

plates attached, as a guide to mark the correct locations

of the 6 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be less

than 3.5 mm in diameter, as shown in the figure at the

right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into one

of the keyhole-shaped apertures of the wall mounting plates.

DO NOT screw the screws in completely—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

STEP 3:

Once the screws are fixed in the wall, insert the four screw heads through

the large parts of the keyhole-shaped apertures, and then slide the

PT-G503-PHR-PTP downwards, as indicated. Tighten the four screws for

added stability.

Wiring Requirements

ATTENTION

Safety First!

Be sure to disconnect the power before ins

talling and/or wiring

your Moxa PRP/HSR redundancy box.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size. If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

Be sure to read and follow these important guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•Use the type of signal transmitted through a wire to determine which

wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

•Keep input wiring and output wiring separate.

•When necessary, you should label the wiring to all devices in the

system.

- 7 -

Grounding the PRP/HSR Redundancy Box

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Dual Power Inputs

The PT-G503-PHR-PTP has two sets of power inputs: power input 1 and

power input 2. The top view of the terminal block connector is shown

below.

Take the following steps to wire the dual power inputs:

STEP 1: Insert the neutral/line (N/L) AC or negative/positive (-/+) DC

wires into the terminals.

STEP 2: To keep the AC or DC wires from pulling loose, use a small

flat-blade screwdriver to tighten the wire-clamp screws on the front of the

terminal block connector.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the PT’s bottom panel.

NOTE

Do not connect the dual power inputs to separate power supplies.

Both inputs must be connected to the same power supply.

NOTE

For the HV model with AC wires, if you intend to only use one

power input, be sure to disconnect the other power input (unplug

the power cord or disconnect the power input from the L and N

contacts). Only one power input LED will be on.

- 8 -

TTENTION

Before connecting the PT

-G503-PHR-

PTP to the DC power inputs,

make sure the DC power source voltage is stable.

Wiring the Digital Inputs

The PT-G503-PHR-PTP has one digital input, DI 1. The DI consists of two

contacts from the 5-pin terminal block connector on the

PT-G503-PHR-PTP’s bottom panel. The remaining contacts are used for

the PT-G503-PHR-PTP’s Relay 1. The top view of the terminal block

connector is shown below.

Take the following steps to wire the digital input:

STEP 1: Insert the negative (ground)/positive DI wires into the ┴/I1

terminals.

STEP 2: To keep the DI wires from pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the PT-G503-PHR-PTP’s

bottom panel.

Auto MDI/MDI-X Connection

The Auto MDI/MDI-X function allows users to connect the

PT-G503-PHR-PTP’s 10/100/1000BaseT(X) ports to any kind of Ethernet

device, without needing to pay attention to the type of Ethernet cable

being used for the connection. You may use either a straight-through

cable or cross-over cable to connect the PT-G503-PHR-PTP to Ethernet

devices.

Communication Connections

Each PT-G503-PHR-PTP has 4 types of communication ports:

•3 Gigabit Ethernet ports: 3 10/100/1000BaseTX and

3 100/1000BaseSFP ports

•1 Ethernet console port

•1 USB console port (type B connector)

•1 USB storage port (type A connector)

- 9 -

10/100/1000BaseT(X) Ethernet Port Connection

The 10/100/1000BaseT(X) ports located on the front panel are used to

connect to Ethernet-enabled devices. Most users will choose to configure

these ports for Auto MDI/MDI-X mode, in which case the port’s pinouts

are adjusted automatically depending on the type of Ethernet cable used

(straight-through or cross-over), and the type of device (NIC-type or

HUB/Switch-type) connected to the port.

In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports. We also give cable wiring diagrams for

straight-through and cross-over Ethernet cables.

10/100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

1000Base T(x) RJ45 Pinouts

MDI

MDI-X

BI_DA+

BI_DB+

BI_DA-

BI_DB-

BI_DB+

BI_DA+

BI_DC+

BI_DD+

BI_DC-

BI_DD-

BI_DB-

BI_DA-

BI_DD+

BI_DC+

BI_DD-

BI_DC-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

- 10 -

100Base-FX or 1000Base-X SFP Fiber Port

The Gigabit Ethernet ports on the PT-G503-PHR-PTP are SFP slots, which

require 100Base-FX/1000Base-X or Gigabit mini-GBIC fiber transceivers

to work properly. Moxa provides complete transceiver models for various

distance requirements.

Multi-mode:

1000BaseSX

0 to 550 m, 850 nm (50/125 μm, 400 MHz x km)

0 to 275 m, 850 nm (62.5/125 μm, 200 MHz x km)

1000BaseLX

0 to 1100 m, 1310 nm (50/125 μm, 800 MHz x km)

0 to 550 m, 1310 nm (62.5/125 μm, 500 MHz x km)

Single mode:

1000BaseLH

0 to 10 km, 1310 nm (9/125 μm, 3.5 PS/(nm x km))

1000BaseLHX

0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm x km))

1000BaseZX

0 to 80 km, 1550 nm (9/125 μm, 19 PS/(nm x km))

Multi-mode:

100BaseFX

0 to 5 km, 1300 nm (50/125 μm, 800 MHz x km)

0 to 4 m, 1300 nm (62.5/125 μm, 500 MHz x km)

Single mode:

100BaseFX

0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm x km))

The concept behind the LC port and cable is quite straightforward.

Suppose you are connecting devices I and II. Unlike electrical signals,

optical signals do not require a circuit in order to transmit data.

Consequently, one of the optical lines is used to transmit data from device

I to device II, and the other optical line is used to transmit data from

device II to device I, for full-duplex transmission.

Remember to connect the Tx (transmit) port of device I to the Rx (receive)

port of device II, and the Rx (receive) port of device I to the Tx (transmit)

port of device II. If you make your own cable, we suggest labeling the two

sides of the same line with the same letter (A-to-A and B-to-B, as shown

below, or A1-to-A2 and B1-to-B2).

USB Console Connection

The PT-G503-PHR-PTP has one USB console port (type B connector),

located on the bottom panel. Use the USB cable (provided in the product

package) to connect the PT-G503-PHR-PTP’s console port to your PC’s

USB port and install the USB driver (available in the software CD) on the

PC. You may then use a console terminal program, such as Moxa PComm

Terminal Emulator, to access the PT-G503-PHR-PTP’s console

configuration utility.

USB Console Port (Type B Connector) Pinouts

Description

D- (Data-)

VCC (+5V)

D+ (Data+)

GND (Ground)

USB Storage Connection

The PT-G503-PHR-PTP has one USB storage port (type A connector) on

the bottom panel. Use Moxa’s ABC-02-USB-T automatic backup

configurator to connect the PT-G503-PHR-PTP’s USB storage port for

configuration backup, firmware upgrade, or system log file backup.

Inhaltsverzeichnis

Andere Moxa Technologies Schalten Handbücher

Moxa Technologies

Moxa Technologies EDS-G308 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-G205-1GTXSFP Handbuch

Moxa Technologies

Moxa Technologies TN-5308-LV Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7528 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-508 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 400A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-G7509 Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-516A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-600 Series Handbuch

Moxa Technologies

Moxa Technologies EDS-516A Series Handbuch

Moxa Technologies

Moxa Technologies EDS-510E Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-30 Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510A-8PoE Series Handbuch

Moxa Technologies

Moxa Technologies EDS-508 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EDS-405A Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTransPT-7528 Series Handbuch

Moxa Technologies

Moxa Technologies EtherDevice EDS-205A series Handbuch

Moxa Technologies

Moxa Technologies EDS-510E Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510-T Bedienungsanleitung

Moxa Technologies

Moxa Technologies PT-7710 Series Handbuch

Moxa Technologies

Moxa Technologies ToughNet TN-5816A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PowerTrans PT-7828 Handbuch

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung