MPSC HeRO solo Kurzanleitung

HeRO

solo/duet

Version 3.1

Customer Assembly & Maintenance Procedure

solo / duet Customer Assembly & Maintenance Procedure

Table of Contents

1. Purpose 3

2. Scope 3

3. Materials 3

4. Assembly Procedure –Desktop Mount 3

5. Assembly Procedure –Pole Mount 4

6. Maintenance Procedure 10

Change Date and Time Settings on HeRO Duet/Solo 10

solo / duet Customer Assembly & Maintenance Procedure

HeRO solo /duet Customer Assembly & Maintenance Procedure

1. Purpose

1.1. Un-packing and assembly instructions for HeRO duet/solo at distributor / customer

sites.

1.2. Instructions for maintenance of HeRO duet/solo equipment.

2. Scope

2.1. HeRO solo /duet on GCX pole or desk top mounts.

3. Materials

3.1. For assembly, the following items will be needed:

a. Phillips screwdriver

b. 3/16” Hex wrench (included)

c. ½” socket wrench (included)

d. Ruler (30 mm length minimimum)

3.2. For maintenance, the following items will be needed:

a. USB Keyboard

b. USB Mouse

HeRO solo / duet should be located in a position that allows access to

the electrical mains connection and does not block the mains disconnect device,

if present.

4. Assembly Procedure –Desktop Mount

4.1. Two 18-8 SS Metric Pan Head Phil Machine Screw M4 Size, 8mm Length are used for

the top holes, two black screws that come with the Advantech are used for the middle

holes, and two Metric 18-8 SS Truss Head Phil Machine Screw M4 Size, 6mm Length are

used for the bottom holes. Mount the AD2 using 4 L-brackets. See Figures 1 and 2.

solo / duet Customer Assembly & Maintenance Procedure

5. Assembly Procedure –Pole Mount

Equipment Required: Philips Screwdriver & Ruler (30mm length minimum)

5.1. Remove all of the items from the large shipping box.

5.2. Put a soft pad on the floor and lay the pole with VESA plate attached on the soft surface

with the face of the VESA plate facing up.

5.3. Take the hexagonal clamp with the power supplies attached and slide it up the pole.

Fasten it to the pole so that the top of the clamp is 120 ± 5 mm from the bottom of the

point where the VESA plate attaches to the pole.

5.4. Take the hexagonal clamp with the cable cleat attached and slide it up the pole. Fasten

it to the pole so that the top of the clamp is 247 ± 5 mm from the bottom of the point

where the VESA plate attaches to the pole. Don’t tighten this clamp completely as you

will have to adjust this when attaching the AD2.

Please note the

orientation of the

VESA mount with

respect to the

power supply

holsters and

cable cleat

Figure 1

Figure 2

solo / duet Customer Assembly & Maintenance Procedure

5.5. Attach the roll stand base with the supplied wrench.

5.6. Use these clips to attach the AD2 to the hexagonal clamps.

5.6.1. Slide the clips into the channel on the AD2.

solo / duet Customer Assembly & Maintenance Procedure

5.6.2.The slots in the clips go under the screws in the clamps.

5.6.3.Adjust the bottom clamp as needed so that the screws are in the slots and then tighten the

screws firmly onto the clips and tighten clamps on the pole. This will lock the AD2in place.

Stand the unit upright.

Please note the

orientation of the

VESA mount with

respect to the

power supply

holsters and

cable cleat

solo / duet Customer Assembly & Maintenance Procedure

5.7. Put two 6 mm M4 screws into the top two holes in the HeRO duet/solo Monitor.

5.8. Slide the HeRO duet/solo Monitor into the slots in the VESA mount. Turn the black lever anti -

clockwise to allow the VESA mount to swivel. You may have to loosen the two screws next to

the lever with a 5/32” (4mm) Allen wrench to allow the mount to move.

solo / duet Customer Assembly & Maintenance Procedure

5.9. Put two 6 mm M4 screws into the bottom two holes in the VESA mount and into the HeRO

duet/solo Monitor. Securely tighten all four screws

5.10. Attach the 1 meter network cable to the HeRO duet/solo Monitor (removecover on back of

monitor to access network ports) and the port on the AD2. Assure that the network cable is

firmly attached at both ends by slightly tugging on the cable.

Turn the black

lever anti-

clockwise to

allow the VESA

mount to swivel.

You may have to

loosen the two

screws next to the

lever with a 5/32”

(4mm) Allen

wrench to allow

the mount to

move.

solo / duet Customer Assembly & Maintenance Procedure

AD2 power

supply

HeRO

duet/solo

monitor

power

supply

5.11. Attach the power cords to the power supplies and the power supply to the appropriate device .

5.12. Attach the cord management clips to pole as needed.

5.13. Connect the HeRO cables (orange and purple) to the color coded channels on the

AD2. (Note: Image shows AD2 with all connections.)

solo / duet Customer Assembly & Maintenance Procedure

6. Maintenance Procedure

Routine maintenance required for HeRO duet/solo includes time/date adjustment. Since the

system is not connected to the internet and/or server to synchronize time, the time may drift.

To minimize this action, MPSC recommends that time/date settings are checked annually and

adjusted if necessary.

Note: Please check the serial number on the back of the HeRO duet/solo monitor to

determine which set of instructions are applicable to your system. If the serial number

begins with ACD, ADE or ACF please use Instruction #1. All other systems should use

Instruction #2 to change date and time settings on HeRO Duet/Solo.

Instruction #1: Change Date and Time Settings on HeRO Duet/Solo

Equipment Required: USB Keyboard and Mouse

1. Remove the plastic cover from the back of the HeRO duet/solo

monitor (Figure 1).To remove, apply pressureto the top of the

AD2 Power Cord

Data

cable to

HeRO

duet/solo

monitor

Andere Handbücher für HeRO solo

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MPSC Messgerät Handbücher

MPSC

MPSC HeRO solo Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung