Musical Fidelity Tri-Vista Bedienungsanleitung

Tri-Vista Power Instructions for Use Page 1of 9

Issue 1: March 2003

Tri-Vista

MONOBLOC POWER AMPLIFIER

INSTRUCTIONS FOR USE

Thank you for purchasing the Musical Fidelity

Tri-Vista Power Amplifier.

Used properly and carefully, it should give you many

years of outstanding musical reproduction.

Aesthetically, the Tri-Vista Power amplifier is a perfect match for the

Tri-Vista Preamplifier and Tri-Vista SACD player which are part of

our 20th Anniversary series.

Together, they form one of the finest hi-fi systems available today.

Dust regularly with a soft duster or soft brush but be

careful when using cleaning or polishing agents - they may

harm the surface finish.

If you have any questions about your audio system,

please consult your dealer who is there to help and advise.

Tri-Vista Power Instructions for Use Page 2of 9

SAFETY INFORMATION

Issue 1: March 2003

IMPORTANT! (U.K. only)

This unit is supplied in the U.K. with a mains lead fitted with a moulded 13 amp plug.

If, for any reason, you need to cut off this plug, please remove the fuse holder and dispose of

the plug safely, out of reach of children. It must not be plugged into a mains outlet.

The wires in the mains lead supplied with this appliance are coloured in accordance

with the following code:

Green and yellow ........... Earth

Blue ............................ Neutral

Brown ............................. Live

WARNING - This appliance must be earthed

As the colours of the wires of the mains lead of this appliance may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug

which is marked with the letter E or coloured green or green-and-yellow, or by the earth

symbol:

The wire which is coloured brown must be connected to the terminal which is marked with the

letter L or coloured red.

The wire which is coloured blue must be connected to the terminal which is marked with the

letter N or coloured black.

If connecting to a BS1363 plug, a 13 amp fuse must be used.

WARNING:

The Tri-Vista Power is a powerful amplifier and must necessarily supply high

voltages through the loudspeaker terminals. Therefore, to avoid any possibility of

an electric shock DO NOT TOUCH THE SPEAKER TERMINALS when the unit

is being used.

WARNING:

Any modifications to this product not expressly approved by Musical Fidelity who

is the party responsible for standards compliance could void the user’s authority to

operate this equipment.

Tri-Vista Power Instructions for Use Page 3of 9

Issue 1: March 2003

GENERAL ADVICE

INSTALLATION PRECAUTIONS and USER INFORMATION

Your new Tri-Vista Power amplifier is designed and built to provide trouble-free performance,

but as with all electronic devices it is necessary to observe a few precautions:

Heed all warnings shown on the back of the product.

Only connect the Tri-Vista Power amplifier to a mains outlet having the same voltage as

marked at the back of the unit.

Always ensure that when disconnecting and reconnecting your audio equipment the mains

supply is switched off.

Position the mains lead and signal interconnects where they are not likely to be walked on or

trapped by items placed on them.

Do not use near water, or place water-filled containers on the amplifier, for example, flower

vases or potted plants. If water does spill inside, immediately pull out the mains plug from

the wall socket and inform your dealer, who should then check the unit before further use.

Entry of liquid into the amplifier is dangerous, and may cause electric shock or fire hazard.

Do not place the unit near heat sources such as radiators, direct sunlight or other equipment.

The case of this amplifier can run at high temperatures - operate the unit in a well ventilated

area, and do not touch the side heatsink fins after periods of use at high output power.

Do not remove covers or try to gain access to the inside. There are no internal user adjust-

ments. Refer all service work to an authorised Musical Fidelity agent.

NOTE: Unauthorised opening of the equipment will invalidate any warranty claims.

There are fuses inside the Tri-Vista amplifier. In the unlikely event that one blows, refer the unit

to your audio dealer. Do NOT try to replace the fuse yourself as this will invalidate the war-

ranty.

Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing

agents - they may harm the surface finish.

The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected

or damaged by lightning. For protection of your audio system during electrical storms, remove

the mains plugs and disconnect any aerial lead.

If after-sales service is required, to help your dealer identify the Tri-Vista amplifier please quote

the serial number located on the rear panel of the unit.

RADIO FREQUENCY INTERFERENCE (R.F.I)

This product has been tested to ensure that its operation is not adversely affected by normal

background levels of R.F.I., and that it does not itself generate excessive amounts of interfer-

ence. However, if a problem persists, please contact your Musical Fidelity agent.

Tri-Vista Power Instructions for Use Page 4of 9

Issue 1: March 2003

Audio input socket (RCA type)

Front panel

Back panel

Illuminated feet with multi-colour indicator LEDs

CONNECTIONS AND FACILITIES - MAIN UNIT

Power supply lead input - low voltage

Mains input from

power supply unit

Control lead socket

Speaker output

terminals

(three pairs)

Tri-Vista Power Instructions for Use Page 5of 9

Issue 1: March 2003

CONNECTIONS AND FACILITIES - POWER SUPPLY

Power supply unit back panel

10 Right channel PSU fuse

11 Right PSU low voltage output

12 Control circuit fuse

13 Left PSU low voltage output

14 Left channel PSU fuse

15 Mains switch

16 Mains inlets - 16 Amp IEC type (two)

17 Right PSU switched mains output

18 Right control lead socket

19 Left control lead socket

20 Left PSU switched mains output

Power supply unit front panel

1Power-on button

2Power-off button

3Fluorescent display - see page 7

4Left power indicator LED

5PSU power indicator LED

6Right power indicator LED

7Display brightness button

- see page 7

8Display information change button

- see page 7

9Illuminated feet with multi-colour

indicator LEDs

1 2 7 8

3456

10 11 12 13 14 15

16 17 18 19 20 16

Tri-Vista Power Instructions for Use Page 6of 9

AUDIO CONNECTIONS

Either of the two Tri-Vista Power ampli-

fiers can be used with a preamplifier or

line level source which has a volume con-

trol. We highly recommend the matching

Tri-Vista preamplifier available from

Musical Fidelity.

Connect the left and right audio outputs

from your pre-amplifiers to the RCA input

sockets on each of the two Tri-Vista power

amplifiers marked INPUT, using good

quality co-axial audio leads (not supplied).

LOUDSPEAKER CONNECTIONS

Using the accessory speaker leads supplied,

connect your loudspeakers to the terminals

on the back panel marked SPEAKER

OUTPUTS. Any of the three pairs of ter-

minals provided can be used. The wiring

must be “in phase”, namely, the +and -

terminals connected to the left and right

speakers the same way round.

Warnings:

The Tri-Vista Power amplifier has a

very large output capability. All input,

output and power connections must

therefore be reliable, and made with the

mains power switched OFF to prevent

possible damage to your loudspeakers.

The negative (black) terminal is part of

a “bridged” circuit, and therefore has

live speaker output. It must not be con-

nected to any chassis or earth terminal.

Issue 1: March 2003

POWER CONNECTIONS

There are three accessory interconnection

leads supplied for each of the two

monobloc amplifiers, two leads for low

voltage and one thick armoured mains

cable. Connect one set of leads between

the power supply unit and the left channel

amplifier sockets, and the other set from the

power unit to the right amplifier sockets.

Left and right channel destinations must be

as shown by the panel socket markings.

Plug the two accessory IEC mains leads

into the rear panel sockets of the power

supply unit, then the other ends into con-

venient wall outlets.

BEFORE SWITCHING ON . . . . .

Turn the volume control on your preampli-

fier to minimum, and switch on its power.

OPERATION

Press the POWER rocker switch on the

back panel of the power supply unit. A sin-

gle blue PSU POWER LED on the front

panel will light to confirm that power is

applied, but the system will not operate, as

control is now from the front panel.

To switch on, press the ON button on the

front panel. One amplifier will power up

first, then after a short delay the other chan-

nel, confirmed by left and right blue power

LEDs on the front panel.

LEDs in the feet of the amplifiers and

power supply will also light red for about

six seconds, indicating that all audio out-

puts are muted. Muting is then disabled,

and feet illumination fades over approxi-

mately fifteen seconds to amber, showing

that your Tri-Vista Power amplifiers are

now ready for use.

continued . . .

CONNECTIONS and OPERATION

Tri-Vista Power Instructions for Use Page 7of 9

OPERATION (contd.) &FLUORESCENT DISPLAY

Issue 1: March 2003

BRIGHTNESS

Pressing the BRIGHTNESS button on the

power supply front panel cycles the fluo-

rescent display through five brightness

levels.

DISPLAY INFORMATION

Each time the INFOrmation button on the

power supply front panel is pressed, the

display mode changes between three

states. Note that the display still functions

if power to the amplifiers has been

switched off by the OFF button.

When the button is pressed for the first

time after the system has been switched on,

the display shows the total number of

hours the amplifiers have been powered :

Press again . . .

. . . the serial number is shown :

Press again . . .

. . . the model number is shown :

Press again . . .

. . . the display reverts to its initial state :

Select the required audio input source on

your pre-amplifier, and adjust the volume

control to obtain the preferred sound level.

After a period of about 35 minutes, the

LED feet colour fades to blue, confirming

that the amplifiers are fully warmed up.

Pressing the OFF button turns off the dis-

play and power to both amplifiers.

AUTOMATIC FAULT DETECTION

If there is a fault with either left or right

channel, or the cables are not connected

correctly, that channel will shut down auto-

matically.

There are sensors in each channel to detect

adverse operating conditions. Under these

conditions the display shows the word

CLIPPING and a number between 1 and

240 depending on severity. If this number

reaches 240, both amplifiers will shut

down.

Similarly, if a major overload is detected by

either amplifier, both amplifiers will shut

down immediately.

Note :

After an initial “burn-in” period of 168

hours in the factory, this counter has been

set to zero.

The fluorescent display then shows the fol-

lowing automatic sequence:

Tri-Vista Power Instructions for Use Page 8of 9

PROBLEMS ?

Issue 1: March 2003

Basic problem-solving with an amplifier is similar to troubleshooting any other electrical or

electronic equipment. Always check the most obvious possible causes first, such as the

following:

If none of these actions effect a cure, please contact your dealer, or an authorised Musical

Fidelity service agent. Remember, never open the case of the Tri-Vista Power amplifier your-

self, as this will invalidate the guarantee.

Problem Possible Cause Remedy

No power when MAINS Mains plug or plugs not Plug in securely

POWER switch is operated inserted fully into rear socket

No sound Tape monitor function has Switch off tape monitor

been selected on the pre- at the pre-amplifier

amplifier

Wrong connections between Check audio input lead

pre-amplifier and the connections

Tri-Vista Power

Speakers not connected, or Check speaker cables

incorrectly wired

The sound is not precise, Speakers are connected out of Ensure method of conn-

lacking bass and stereo phase, i.e. connections to one ection is the same for left

image speaker (+ and -) are reversed and right speakers

Tri-Vista Power Instructions for Use Page 9of 9

SPECIFICATIONS :

Output voltage, RMS 92 Volts 20Hz to 20kHz

peak 130 Volts

Power output, single or both channels driven 1000 Watts per channel into 8 Ohms (24dBW)

1800 Watts per channel into 4 Ohms

3000 Watts per channel into 2 Ohms

Peak output current ±200 Amps

Damping factor 205

Output devices per channel 40

Total Harmonic Distortion + noise 0.005% at 1kHz up to 80% power, into 8 Ohms

< 0.005% 20Hz to 20kHz at 12.5 Watts into 8 Ohms

Intermodulation distortion 0.002% at 12.5 Watts into 8 Ohms

Frequency response 20Hz to 20kHz ±0dB

10Hz to 100kHz +0/-1dB

Audio gain 30dB (31.5 times) nominal

Input impedance 31K Ohm

Input sensitivity for full power output into 8 Ohms 2.92 Volts

Signal / noise ratio, reference full power output > 124dB “A”- weighted

Input 1 RCA connector per monobloc

Outputs 2 monobloc channels via 3 pairs of speaker binding posts

per channel,

Power requirements 100 / 115 / 230V AC, 50 / 60Hz (factory preset)

3000 Watts maximum with 8 Ohms load

160 Watts idle per channel

Dimensions Main units 483 mm, 19 inches wide

318 mm, 12.5 inches high including feet

450 mm, 17.7 inches deep including terminals

Power supply 483 mm, 19 inches wide

168 mm, 6.6 inches high including feet

374 mm, 14.7 inches deep including sockets

Weight Main units, each 43 kg, 94.8 lbs unit only, unboxed

61 kg, 135 lbs in shipping carton

Power supply 42.7 kg, 94.1 lbs unit only, unboxed

48.2 kg, 106 lbs in shipping carton

Standard IEC mains leads - 16 Amp type :two, 2.4 metres (94.5 inches) each

accessories Switched mains interconnection leads :two, 1.2 metres (47.3 inches), and 0.7 metres (27.5 inches)

Low voltage interconnection leads :two, 1.2 metres (47.3 inches), and 0.7 metres (27.5 inches)

Control interconnection leads :two, 1.2 metres (47.3 inches), and 0.7 metres (27.5 inches)

Loudspeaker leads :two, twin conductors, 3 metres (118 inches) each

Issue 1: March 2003

Musical Fidelity reserves the right to make improvements which may result in specification or feature changes without notice.

Tri-Vista

Power Amplifier

CAUTION

Read this BEFORE connecting your

kW Amplifier - it could save your

loudspeakers.

Make sure the kW is turned OFF for at least five

minutes before connecting or disconnecting it, or

making any other changes, for example changing

loudspeaker cables.

Turning the kW OFF will protect your loudspeakers

from the destructive power of an accidental 5000

watt peak.

Because the kW will NOT CLIP, any inadvertent

electrical noise will be hugely amplified by the kW.

As the kW can deliver 5000 watt peaks, a mistake

could vaporise the internals of your loudspeakers.

At the factory, we ALWAYS switch off the kW for

at least five minutes before we change anything.

So should you. You have been warned . . .

COVER

Andere Handbücher für Tri-Vista

Inhaltsverzeichnis

Andere Musical Fidelity Verstärker Handbücher

Musical Fidelity

Musical Fidelity M3I Bedienungsanleitung

Musical Fidelity

Musical Fidelity M1 HPAP Bedienungsanleitung

Musical Fidelity

Musical Fidelity AMS35i ANTONY MICHAELSON Bedienungsanleitung

Musical Fidelity

Musical Fidelity M6sPRE Bedienungsanleitung

Musical Fidelity

Musical Fidelity M1 HPAP Bedienungsanleitung

Musical Fidelity

Musical Fidelity A3.2 CR Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-80 Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-LPSV8 Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-CAN V8P Bedienungsanleitung

Musical Fidelity

Musical Fidelity MERLIN Bedienungsanleitung

Musical Fidelity

Musical Fidelity NU-VISTA Series Bedienungsanleitung

Musical Fidelity

Musical Fidelity M8xi Bedienungsanleitung

Musical Fidelity

Musical Fidelity A1001 Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-A2 Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-LP2 Bedienungsanleitung

Musical Fidelity

Musical Fidelity MX-VYNL Bedienungsanleitung

Musical Fidelity

Musical Fidelity V90-AMP Bedienungsanleitung

Musical Fidelity

Musical Fidelity F2 Bedienungsanleitung

Musical Fidelity

Musical Fidelity M1PWR Bedienungsanleitung

Musical Fidelity

Musical Fidelity Nu-Vista 800 Bedienungsanleitung

Musical Fidelity

Musical Fidelity MM/MC PHONO STAGE M1 VINL Bedienungsanleitung

Musical Fidelity

Musical Fidelity A3cr Bedienungsanleitung

Musical Fidelity

Musical Fidelity A5.5 Bedienungsanleitung

Musical Fidelity

Musical Fidelity X-Pre V3 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung