MYE MWC-9 Bedienungsanleitung

Operation Manual

MWC-9 900MHz Controller

MWC-9

Operation Manual

www.myeclubtv.com

manmwc9

CONTENTS

FCC Compliance Statement…………………..…………. 3

Canada Compliance Statement………………………….. 3

Specifications………………………………………….… 3

Controller Orientation (Front / Rear)…………………… 4

Keypad – Key Identification………………………….… 5

Main Features…………………………………………… 5

Display and Icon Identification…………….…………… 6

Programming - Near / Far Reception Setting…………… 6

Programming the Receiver Controller (Auto Programming)… 7

Programming the Receiver Controller (Manual Programming) 7

Attaching the Controller………………………………… 8

Intellijack…………………….………………………….. 9

Special Features…(FitP3)………………..………….….. 10

Special Features…(Auto Off)………………..…………. 10

Warranty Information…………..…………..….……..…. 11 /12

NOTE: This equipment has been tested and found to comply with the limits for a class B digital devise

pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in

a residential environment. This equipment generates, uses and can radiate radio frequency energy and if not installed and

used in accordance with the instruction manual may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the unit off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•Reorient or relocate the receiver.

•Increase the separation between the equipment and the receiver.

•Connect the equipment to an outlet different from that which the receiver is connected.

•Consult your MYE dealer or experienced Radio / TV technician

FCC Compliance Statement

INDUSTRY CANADA COMPLIANCE STATEMENT

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Canada Compliance Statement

Parameter 900 MHz Receiver

Frequency Range 903.000 TO 926.0000 MHz

Input Sensitivity (20 dB SINAD) -85 dBm typical

Modulation FM Stereo deviation +/- 75KHz

Stereo Separation >25dB

Equalization BASS, FLAT,JAZZ, CLASSICAL

Audio Frequency Response 20 Hz to 13 kHz

Frequency Entry Scroll up/down.

Power 3.75 VDC TO +12VDC

SPECIFICATIONS

The MYE MWC-9 Receiver allows the user to watch and listen to any TV or other source connected to a

900MHz Transmitter. The user may also listen to the optional MYE FitP3 Music and Podcast Player when

docked. The MWC-9 can be powered directly from any standard CSAFE port using a MYE Entertainment

CSAFE cable or by an optional 9 VoltAC Adapter. Patent Pending

Product Description

UPPER LATCH

LOWER LATCH

UPPER LATCH

LOCKING SCREW

LOWER LATCH

LOCKING SCREW

CONTROLLER REAR VIEW

CONTROLLER FRONT VIEW

LCD DISPLAY

HEADPHONE JACK

ICON

HEADPHONE JACK

CONTROLLER KEYPAD

FITP3 PLAYER DOCK

MYE Wireless 900MHz TV Receiver

Model MWC-9

The MYE MWC-9 Receiver allows the user to watch and listen to any TV or other source

connected to a 900MHz Transmitter. The user may also listen to the optional MYE FitP3 Music

and Podcast Player when docked. The MWC-9 can be powered directly from any standard

CSAFE port using a MYE Entertainment CSAFE cable or by an optional 9 VoltAC Adapter.

Main Features:

FitP3 Button

Selects audio from the optional

FitP3 Player when FitP3 player is docked.

TV Button

Selects audio from TV’s connected to a

900MHz Transmitter

Channel Up/Down Buttons

Selects desired TV number

Volume Up/Down Buttons

Controls Volume Level Up and Down

Power Button

Turns Receiver ON/OFF

Mute

Mute ON or OFF

EQ Select

Select between 5 preset EQ tones:

Flat, Rock, Jazz, Classical & Bass

MWC-9 KEY IDENTIFICATION

FITP3 SELECT

CHANNEL UP

CHANNEL DOWN

FITP3 SKIP FORWARD

TV SELECT

VOLUME UP

VOLUME DOWN

EQ SETTING SELECT

MUTE

POWER ON / OFF

FITP3 PLAY / PAUSE

DISPLAY WINDOW

Programming - Far/Near Reception

This feature provides the ability to set the reception sensitivity of each MYE MWC-9 receiver

depending on the proximity between the receiver and transmitter.

Far Mode: (Default): The far mode is the most widely used and will accommodate the

majority of installations.

Near Mode: The near mode is used primarily in situations where the MWC-9 receiver is

positioned very close to one or more transmitters. The Near Mode is recommended when

receivers are installed between 1 and 5 feet from a transmitter.

Far / Near Mode

Note: The factory default is set to “Far” (HI).

To change to “Near” mode (LO):

1. Start with the MWC-9 in the OFF position.

2. With the unit OFF, press and hold the Volume UP button.

3. While holding the Volume UP button, press and release the POWER button.

4. Wait three seconds while continuing to hold Volume UP button until ‘LO’ is appears

on the display.

5. To revert back to Far mode simply follow steps 1-4 until “HI” appears on display.

DISPLY and ICON IDENTIFICATION

FAULTY

HEADPHONE

JACK

VOLUME

LEVEL

INDICATOR

CHANNEL

FITP3 MODE

SELECTED

CURRENT

CHANNEL

TRANSMITTER

TV MODE

SELECTED

MUTE “ON”

EQ PRESETS

FREQUENCY

DETECTED IN

AUTO PROGRAM

MODE

Programming

The MYE MWC-9 receiver must be programmed to detect and lock in the MYE

Entertainment transmitters as well as the other brands of transmitters listed below. The

MWC-9 features both “auto” and “manual” program modes. In the auto mode the MWC-9

will automatically search for and program in your transmitters. The manual mode provides

the ability to add or erase a specific transmitter channel or unwanted frequency caused by

spurious emissions or other local elements.

Auto Program Mode

1. Press Channel Down and Volume UP buttons simultaneously for three seconds until

“P-1” appears on the display.

2. Press the “>>” OR “<<” buttons to select one of the following program modes:

P-1 = MYE Entertainment 900MHz Transmitters

P-2 = Cardio Theater LCS 900MHz Transmitters

P-3 = Cardio Theater / Enercise xTV 900MHz Transmitters

P-4 = BroadcastVision 900MHz Transmitters

3. After selecting the Transmitter Mode, press the Play button to auto-scan and lock

transmitters.

4. Press the Channel UP or Channel Down buttons to determine all transmitters have

been locked in. NOTE: “PRESET” will appear in the display when a transmitter

channel is programmed.

5. To exit program mode press the EQ button. The display will blink briefly and the will

default to first transmitter channel programmed.

Manual Program Mode (Add or Delete Frequencies)

1. Press Channel Down and Volume UP buttons simultaneously for three seconds until

“P-1” appears on the display.

2. Press the “>>” OR “<<” buttons to select one of the following transmitter program

modes listed above.

3. Press the EQ button

4. Press CHANNEL UP/DOWN buttons to scroll through all transmitter channels.

5. To add or delete a transmitter channel press the “TV” button. NOTE: “PRESET” will

appear in the display when a transmitter channel is programmed.

6. To exit manual program mode press the EQ button. The display will blink briefly and

twill default to first transmitter channel programmed.

Attaching the Controller

1. Remove the rear mounting cup from the controller by loosening the two screws and

opening both metal latches on the back of the controller

2. Attach the rear mounting cup to the desired mounting location by either using the

secure clamp or traditional nylon wire ties. Secure Clamp- Insert screws (included)

3. Insert the Control power cable or CSAFE cable through the square opening of the

rear mounting cup. (PIC 3)

4. Connect the cable to the data port on the rear of the MYE Controller

5. Plug the power supply to an AC outlet or the CSAFE cable to an active CSAFE port.

6. Rotate the MYE Controller so it is vertical and position on the rear mounting cup

7. Lock the Controller in place by securing both metal clamps and tightening screws.

Shallow Cup with Secure Lock Mounting

PIC 3 Shallow Cup with Nylon Wire Tie Mounting

When CSAFE cables are required for power, USE only MYE Entertainment CSAFE cables with all

MYE Entertainment receiver controllers (900 MHz or FM). MYE Entertainment will not be

responsible for damage to controllers or CVE when alternate or other brand cables are used.

IntelliJack - Self Diagnostic Headphone Jack

The IntelliJack self diagnostic headphone circuit detects when the headphone jack has

failed or been damaged. When a faulty headphone jack is detected, a flashing “headphone”

icon appears in the LCD display. It will remain on until a new jack is installed and the icon

reset.

To Replace the Intellijack:

1. Loosen the two screws evenly on the bottom of the IntelliJack module and remove.

2. Carefully insert new IntelliJack module without bending contact pins.

3. Reset the Icon. Turn MYE Controller OFF then press and hold the “Power” button for

3-4 seconds. When the icon appears again release the Power button.

IMPORTANT NOTICE: Faulty headphones may trigger the fault headphone jack icon. It is

important to audibly test the headphone jack prior to replacement. If the headphone jack is

deemed OK simply follow step #3 above to reset the faulty headphone jack.

Special Features:

FitP3 Player Feature-

The MWC-9 controller has the ability to receive the MYE Entertainment FitP3 Player. Insert

the FitP3 Player into the FitP3 docking port. When the FitP3 Player is docked the MP3 Icon

illuminates in the LCD Window

The audio from the Controller, regardless of source will be directed to the headphone jack of

the FitP3 Player. The FitP3 Player can now be controlled through the use of the FitP3

Control Keys on your controller.

FitP3 Basic Functions-

Play & Pause

Back <<

Forward >>

Auto OFF Sensor-

The MYE Controller will monitor for the absence of vibration for 10 minutes. Should this

occur, the console will automatically power OFF saving energy and extending product

lifespan. This feature can be programmed enabled or disabled.

To Enable the Auto OFF Sensor:

1. Press the “Channel Down & Volume” buttons simultaneously for 3-5 seconds unit

the word “OFF” is displayed

2. Press the “TV” button to turn the feature ON or OFF

3. Press the “EQ” button to exit.

Inhaltsverzeichnis

Andere MYE Fernsehempfänger Handbücher

MYE

MYE M15TV-NAQ2 Bedienungsanleitung

Beliebte Fernsehempfänger Handbücher anderer Marken

NEC

NEC PX-TUAN-01 Bedienungsanleitung

Edision

Edision Piccollino Bedienungsanleitung

Matsui

Matsui DTR1 Bedienungsanleitung

Dyon

Dyon Raptor Bedienungsanleitung

Strong

Strong SRT 2401 Betriebsanleitung

TerraTec

TerraTec CINERGY DT USB XS DIVERSITY Gebrauchsanweisung

Haier

Haier 34F9K Bedienungsanleitung

TechniSat

TechniSat DigiCom 1 Bedienungsanleitung

Haier

Haier LT19A1 Bedienungsanleitung

Triax

Triax CR 317 Bedienungsanleitung

DirecTV

DirecTV D10-300 Bedienungsanleitung

Motorola

Motorola VIP2502W Bedienungsanleitung

ActionTec

ActionTec WirelessTV Bedienungsanleitung

Motorola

Motorola VIP1200 Series Bedienungsanleitung

Xoro

Xoro HRT 1300 Bedienungsanleitung

Motorola

Motorola DH6200 Bedienungsanleitung

Manhattan

Manhattan Plaza DS-100 Bedienungsanleitung

Micro Prose

Micro Prose MPI-500 Bedienungsanleitung