MyQ CHAMBERLAIN CHAA250EVC Bedienungsanleitung

CHAA250EVC

* For GB (UK, NI) specic information on national regulations and requirements

see English part of the manual.

en Swing Gate Operator Installation Manual*

fr Manuel d‘installation de l‘opérateur de porte battante

nl Installatiehandleiding draaihekaandrijving

de Installationshandbuch für Drehtorantriebe

cs Instalační manuál pro obsluhu křídlové brány

sk Inštalačný manuál k pohonu krídlovej brány

TABLE OF CONTENTS

NOTE:The original installation and operating instructions were compiled in English. Any other available language is a translation of the original English version.

1. SAFETY INSTRUCTIONS AND INTENDED USE......................................................................................................................................................................................2

2. DELIVERY SCOPE......................................................................................................................................................................................................................................4

3. TOOLS NEEDED.........................................................................................................................................................................................................................................4

4. OVERVIEW OF GATE OPERATOR............................................................................................................................................................................................................4

5. MECHANICAL INSTALLATION....................................................................................................................................................................................................................5

5.1 Dimensions of Gate and Operator.........................................................................................................................................................................................................5

5.2 Determine the Position of the Post Bracket...........................................................................................................................................................................................5

5.3 Post Bracket Installation........................................................................................................................................................................................................................6

5.4 Operator Mounting and Travel Distance Adjustment...........................................................................................................................................................................6

5.5 Emergency Release Mechanism..........................................................................................................................................................................................................8

5.6 Control Board Installation and Motor Wiring........................................................................................................................................................................................8

5.7 Power Wiring.........................................................................................................................................................................................................................................8

6. WIRING DIAGRAM......................................................................................................................................................................................................................................9

7. PROGRAMMING..............................................................................................................................................................................................................................................10

7.1 Display, Programming Buttons and Function Setting.........................................................................................................................................................................10

7.2 General Programming Overview..........................................................................................................................................................................................................10

7.3 Wing Movement Direction...................................................................................................................................................................................................................11

7.4 Basic Settings......................................................................................................................................................................................................................................11

7.4.1 Application Settings..................................................................................................................................................................................................................11

7.4.2 Direction Motor 1 Settings.........................................................................................................................................................................................................11

7.4.3 Direction Motor 2 Settings.........................................................................................................................................................................................................11

7.4.4 Limit Learning...........................................................................................................................................................................................................................11

7.5 Stand-by Mode....................................................................................................................................................................................................................................12

7.6 Programming and Erasing of Remote Controls, Radio Accessories and myQ Devices.......................................................................................................................13

7.7 Advanced Settings..............................................................................................................................................................................................................................14

7.7.1 Overview Advanced Settings....................................................................................................................................................................................................14

7.7.2 Transmitter Settings.................................................................................................................................................................................................................14

7.7.3 Infrared Photocells Settings......................................................................................................................................................................................................14

7.7.4 Input Settings...........................................................................................................................................................................................................................14

7.7.5 Partial Opening Motor 1.............................................................................................................................................................................................................15

7.7.6 Delay Motor 2 in Open Direction..............................................................................................................................................................................................15

7.7.7 Delay Motor 1 in Close Direction..............................................................................................................................................................................................15

7.7.8 Timer to Close..........................................................................................................................................................................................................................15

7.7.9 Reversal Time after Impact.......................................................................................................................................................................................................15

7.7.10 E-Lock / Mag-Lock Settings.....................................................................................................................................................................................................15

7.7.10a Relief Motor 1 for E-Lock.......................................................................................................................................................................................................16

7.7.11 Flashing Light Settings...........................................................................................................................................................................................................16

7.7.11a Pre-Flashing................................................................................................................................................................................................................................16

7.7.12 Special Contact Settings.........................................................................................................................................................................................................16

7.7.13 Start Speed in Open and Close Directions.............................................................................................................................................................................16

7.7.14 Maintenance Counter...............................................................................................................................................................................................................16

7.8 Factory Default Settings....................................................................................................................................................................................................................17

7.9 Finish and Exit...................................................................................................................................................................................................................................17

8. BATTERY BACKUP....................................................................................................................................................................................................................................17

9. ERROR CODES........................................................................................................................................................................................................................................17

10. TECHNICAL DATA....................................................................................................................................................................................................................................18

11. MAINTENANCE.......................................................................................................................................................................................................................................19

12. DISPOSAL.........................................................................................................................................................................................................................................19

13. WARRANTY.........................................................................................................................................................................................................................................19

14. DECLARATION OF CONFORMITY............................................................................................................................................................................................................19

About this Manual – Original Manual

These instructions are the original operating instructions according the machinery directive 2006/42 EC. The instruction manual must be read carefully to understand

important product information. Pay attention to the safety and warning notices. Keep the manual in safe place for future reference and to make it available to all persons

for inspection, service, maintenance and repair. After installation pass the complete documentation to the responsible person/owner.

Qualication of a competent installer

Only correct installation and maintenance by a competent installer (specialist) / competent company, in accordance with the instructions, must understand and ensure the

safe and intended function of the installation. Specialist is, who on the basis of their technical training and experience, has sufcient knowledge in the eld of powered

gates and moreover is familiar with relevant state occupational safety regulations and generally accepted rules of technology in such an extent that he is also able to

assess the safe working condition of powered gates according to EN 13241, 12604, 12453 (EN12635

The installer must understand the following:

Before installing the drive, check that the driven part is in good mechanical condition, opens and closes properly and correctly balanced where applicable

Before rst use and at least annually a specialist must inspect powered gate regarding their safe condition. After installation, the installer must ensure that the mecha-

nism is properly adjusted and that the protection system and any manual release function correctly (EU: EN 13241, EN12604, EN 12453, EN 12635; GB (UK, NI)

BS EN 13241, BS EN12604, BS EN 12453, BS EN12635). A regular maintenance, inspection must be carried out according to the standards. The installer must

instruct other users on the safe operation of the drive system.

After successful installation of the drive system, the responsible installer, in accordance with the EU: Machinery Directive 2006/42/EC; GB (UK, NI): Supply of Machinery

(Safety) Regulations 2008 SI 2008 No. 1597, must issue the EU: CE / GB (UK,NI): UK declaration of conformity for the gate system. The EU: CE / GB (UK,NI): UKCA

mark label must be attached to the gate system. This is also obligatory in the process of retrotting on a manually operated gate. Further, a handover pack and an inspec-

tion book must be completed.

Please read the operating instructions and especially the precautions. The following symbols are placed in front of instructions to avoid personal injury or damage to

property. Read these instructions carefully.

Warnings Symbols

The general warning symbol indicates a danger that can lead to injuries or death. In the text section, the general warning symbols are used as described below.

Intended use

The swing gate operator is exclusively designed and tested for the operation of smooth-running swing gates in the residential, non-commercial sector.

Specication for gates are dened under mechanical requirements according EU: EN12604 / GB (UK, NI): BS EN 12604.

The maximum permissible gate size and the maximum weight must not be exceeded. The gate must open and close smoothly by hand. Use the operator on gates which

comply with the applicable standards and guidelines. Regional conditions of wind loads must be taken into account when using door or gate panels EU: EN13241 / GB

(UK, NI): BS EN 13241. Observe the manufacturer‘s specications regarding the combination of door and operator. Possible hazards within the meaning of EU: EN13241

/ GB (UK, NI): BS EN 13241 are to be avoided by designing and installing the door/gate according to the relevant instructions. This gate mechanism must be installed and

operated in accordance with the appropriate safety rules.

Improper use

It is not intended for continuous operation and use in a commercial application.

The construction of the drive system is not designed for the operation of gates outside of manufacturers specication.

It is not permitted on gates that travel with incline/decline.

Any improper use of the drive system could increase the risk of accidents. The manufacturer assumes no liability for such usage. With this drive, automated gates must

comply with the current, valid international and country-specic/local standards, guidelines and regulations (EU: EN 13241, EN12604, EN 12453; GB (UK, NI) BS EN

13241, BS EN12604, BS EN 12453).

Only Chamberlain and approved accessories may be connected to the drive. Incorrect installation and/or failure to comply with the following instructions may result in

serious personal injury or damage to property.

Gate systems located in public areas and have only force limitation, can only be operated under full supervision.

Additional safety devises should be considered in accordance with EU: EN 12453; GB (UK, NI) BS EN 12453.

DANGER Symbol WARNING Symbol CAUTION Symbol ATTENTION Symbol

DANGER WARNING CAUTION ATTENTION

Indicates a danger that leads directly

to death or serious injuries.

Indicates a danger that can lead to

death or serious injuries.

Indicates a danger that can lead to

damage or destruction of the product.

Indicates a danger that can lead to

damage or destruction of the product.

1. SAFETY INSTRUCTIONS AND INTENDED USE

During operation, the gate should not under any circumstances obstruct public path ways and roads (public area).

When using tools and small parts to install or carry out repair work on a gate exercise caution and do not wear rings, watches or loose clothing.

To avoid serious personal injury due to entrapments, remove any locking device tted to the gate in order to prevent damage to the gate.

Installation and wiring must be in compliance with your local building and electrical installation regulations. Power cables must only be connected to a properly earthed

supply.

Disconnect electric power to the system before installation, maintenance, repairs or removing covers. A disconnecting device must be provided to the mains power supply

(permanently-wired installation) to guarantee all-pole disconnection (isolating switch or by a separate fuse). The repairs and electrical installations may be performed only

by an authorised electrician. Emergency Stop Button must be installed for emergency case based on the risk assessment.

Ensure that entrapment between the driven part and the surrounding xed parts due to the opening movement of the driven part is avoided by respecting the given safety

distances in accordance with the EU: EN 13241, EN12604, EN 12453, EN 12635; GB (UK, NI) BS EN 13241, BS EN12604, BS EN 12453, BS EN12635 and/or with

safety devices (e.g. safety edge).

Testing of the safety function of the drive system is recommended to be carried out at least once a month. Refer also to manufacturers instruction of the gate system

components.

After the installation a nal test of the full function of the system and the of the safety devices must be made and all users must be instructed in the function and operation

of the swing gate operator.

Gate systems must meet the force limitation according EU: EN 12453, EN 60335-2-103; GB (UK, NI) BS EN 12453, BS EN 60335-2-103.

Additional safety device (safety edge,.) must be considered in accordance to the standard by changes to the system.

It is important to make sure that the gate always runs smoothly. Gates which stick or jam must be repaired immediately. Employ a qualied technician to repair the

gate, never attempt to repair it yourself. This device is not intended for use by persons (including children) with restricted physical, sensory or mental abilities or lack of

experience or knowledge, unless they are supervised by a person responsible for their safety or have received instruction in how to use the device. If necessary, control

equipment MUST be mounted within sight of the gate and out of reach of children. Children should be supervised to ensure that they do not play with the device. Do not

allow children to operate push button(s) or remote(s). Misuse of the gate operator system can result in serious injury.

The warning signs should be placed in clearly visible locations.

The gate opener should ONLY be used if the user can see the entire gate area and is assured that it is free of obstacles and the gate operator is set correctly. No one may

pass through the gate area while it is moving. Children must not be allowed to play in the vicinity of the gate.

The full protection against potential crushing or entrapment must work immediately when the drive arms are installed.

There may be existing hazards on mechanical, electrical installation or the closing edges of the gate by crushing, impact points:

• Structural failure, leaf, hinges, xings, travel stops, wind load

• Crush, hinge area, under the gate, safety distance on xed object

• Electrical failure (Control – faults in safety systems)

• Impact, swept area, hold to run, force limitation, presence detection

Appropriate measures must be taken to ensure safe operation of the gate system according the standards.

Never start up a damaged drive.

Use the manual release only to disengage the drive and – if possible – ONLY when is gate closed. Operation of the emergency manual release can lead to uncontrolled

movements of the gate. The Timer-to-Close (TTC) feature, the myQ Smartphone Control app, are examples of unattended operation of the gate.

Any device or feature that allows the gate to close without being in the line of sight of the gate is considered as unattended open/close.

The Timer-to-Close (TTC) feature, the myQ Smartphone Control, and any other myQ devices can ONLY be activated when Chamberlains photo cells are installed (TTC

works only in close direction). The gate shall only be operated in the direct sight line to the gate.

IMPORTANT INFORMATION!

• This procedure is also required on private installations (new or retrotted to a manually operated gate).

This installation and operating manual must be retained by the user.

• The manufacturer accepts no liability/warranty claims resulting from use other than intended use and after the warranty expires.

• The legal remedy is the sole responsibility for all associated rights.

NOTE: Observe the installation and operating manual.

• Always monitor the function of the system and rectify the cause immediately in the event of a malfunction.

• Carry out an annual inspection of the system. Call a specialist.

• Safety distances must be respected between the gate leaf and the environment in accordance with related standards.

• The operator can be installed Only on stable and rigid gate leaves. Gate leaves must not bend or twist when opening and closing.

• Assure that the hinges of the gate leaf are installed and working correctly and not creating any obstacles.

• Installation of two operators on same door leaf is strictly prohibited.

1. SAFETY INSTRUCTIONS AND INTENDED USE

CHAA250EVC

Post Mounting

Bracket (2x)

13, 14 mm 6 mm

Screw and nut

(4x)

Cover (2x) Screw and

Washer (2x)

Strain relief

4 x M16

2 x M20

Grommets

(6x)

Hardstops (4x)

Screws + Washers (4x)

Gate Mounting

Bracket (2x)

Pin (2x) Circlip pin (2x)

Release Key

(4x)

Remote

Control (2x)

Primary unit with

Control Board

Secondary unit

Installation

Manual

1. Motor 1 with control board

2. Motor 2

3. Post bracket (concealed)

4. Gate bracket

5. Infrared photocells

6. Flashing lamp

2. DELIVERY SCOPE

3. TOOLS NEEDED

4. OVERVIEW OF GATE OPERATOR

Photocell

5.2 Determine the Position of the Post Bracket

1. Determine the A, B and C dimensions based on the opening angle provided in Table 1 to conrm the position where the post bracket will be mounted.

NOTE: All crushing points must be secured by an entrapment protection according to EU: EN 12453, EN 60335-2-103; GB (UK, NI): BS EN 12453, BS EN 60335-2-103.

CHAA250EVC

Example installation

CHAA250EVC

1.5 m 200 kg

2.0 m 150 kg

2.5 m 100 kg

Operator Arm Mounting

1. Attach the motor arm to the center of the opener from

the underside.

2. Secure the caps with the screw and washer.

175 mm265 mm

250 mm

280 mm

Picture 1

13 mm

54 mm

30 mm

159 mm

Ø 8.5 mm

96 mm

Ø 8.5 mm

100 mm

60 mm

20 mm

A B C

Opening angle mm

90° 150-300 390-540 0-300

120° 300-350 300-350 0-25

Table 1

min. 200 mm

20 mm

min. 420 mm

max. 120°

48.5 mm

Herewith you start mechanical installation of the gate operator.

5. MECHANICAL INSTALLATION

5.1 Dimensions of Gate and Operator

1. Using the post bracket as a reference, mark and drill the holes for the post bracket.

2. Attach the post bracket using the correct fastening material based on existing installation (building / material substance). Please consult the gate manufacturer.

3. The slots on the post bracket allow for alignment. When the post bracket is level tighten the nuts.

5.4 Operator Mounting and Travel Distance Adjustment

1. Align the holes on the operator to the post bracket holes and connect using the screws and nuts (see picture 3.a).

2. Connect the arm to the shaft of the motor unit (see picture 3.b). Do not mount plastic protection cover yet, if you plan to install operator hard stops.

3. Release the operator clutch with the release key (see picture 4 on page 7).

4. Bring gate leaf to the closed position.

NOTE: The system must operate with external gate or operator hard stops in both directions.

5.4.1 Installation with external gate hard stops: (gate hard stops already installed)

a. Position the gate bracket in the desired full closed position as shown in the picture 3.c. Temporarily secure it to the gate leaf and connect with operator arm considering

dimensions A, B and C from Table 1.

b. Manually open and close the gate to the required positions. Ensure the operator arm does not bind and gate is moving smoothly.

c. Make permanent connection of the gate bracket at chosen correct position.

5.4.2 Installation with operator hard stops: (no gate hard stops installed)

a. Position the gate bracket in the desired full closed position as shown in the picture 3.c. Temporarily secure it to the gate leaf (do not make permanent connection to

gate leaf yet to enable adjustments) and connect with operator arm considering dimensions A, B and C from Table 1.

b. Manually open and close the gate to the required positions. Ensure the operator arm does not bind and gate is moving smoothly.

c. Fix the operator hard stop for “close” position as close as possible to the arm (see picture 3.d).

Hold the gate leaf in the desired “closed” position and adjust position of the gate bracket, so that the arm pushes against hard stop in “close” position (see pictures 3.e and 3.f).

d. Make permanent connection of the gate bracket at chosen correct position.

e. Open the gate to the required “open” position and x the operator hard stop for “open” position as close as possible to the arm (see pictures 3.g and 3.h).

f. Mount the protection cover at the operator bottom (see picture 3.i).

4.3 A combination of operator and gate hard stops is allowed. Please use the respective set up procedures as described above.

5. Repeat the procedure for the unit on the opposite side.

5.3 Post Bracket Installation

NOTE: For brick or concrete posts please use correct dowels and screws. Please

maintain correct distance to the post edges.

For metal posts please consider the post thickness and weld or bolt the bracket

directly to post.

For timber posts please use correct screws and if required use reinforcement plates.

Caution: The fastened brackets must not loosen after installation and during operation.

Picture 2

3.a 3.b

13 mm

6 mm

3.c

5.MECHANICALINSTALLATION

Picture 3

INSTALLATION

5.5 Emergency Release Mechanism

To disengage the release mechanism remove the plastic cover, enter the key and turn it 90°.

Pull the clutch up (see picture 4). To re-engage the release meachanism, push the clutch down and turn the key 90°.

3.d

3.h

3.f

3.g

3.e

max. 120°

3.i

Picture 4

4.a 4.b

The control board is already pre-installed in the Primary unit and pre-wired to the terminals of Motor 1.

To gain access to the control board in the Primary unit release the 2 screws on the sides of the cover and 2 screws on the back of the Primary unit (see picture 5).

The terminals for wiring accessories are directly accessible. To get access to the programming buttons remove the transparent plastic cover and place it back once pro-

gramming is nished (see picture 6). Remove the cover of the Secondary unit same way as with Primary unit to gain access to the Motor wiring terminal (see picture 7).

5.7 Power Wiring

Mains power wiring must be done by a certied electrician specialist.

Motor 2 Connection

NOTE: The operator wired to the MOTOR 2 terminal will always open last and close rst.

Consider this for Basic and Advanced Settings (see Programming section).

1. Connect the extension cable (not provided) to the wiring terminals of the Secondary

unit (see picture 7).

Note the cable colors of the Secondary motor to match them on the control board wiring

terminal for MOTOR 2.

2. Feed the Secondary motor extension cable through one of the cable glands at the bottom

of the Primary unit (see picture 8). Ensure to use the side of the motor where the arm cannot cut the cables

during opening or closing movement.

3. Connect Secondary motor cables to the MOTOR 2 terminals as follows: red cable to RED terminal, green cable to GRN terminal , white cable to WHT terminal on

control board.

5.6 Control Board Installation and Motor Wiring

INSTALLATION

Motor 1 Connection

NOTE: The operator wired to the MOTOR 1 terminal will always open rst and close last.

Consider this for Basic and Advanced Settings (see Programming section).

Primary unit is already pre-wired to MOTOR 1 terminals. No extra steps required for Motor 1 wiring.

Per default settings, the Primary unit is considered installed on the left (when looking from inside out), and the Secondary unit on the right.

In case the Primary unit is installed on the right, and the Secondary unit on the left, change the settings of functions «d1» and «d2».

Primary unitRemoving CoverPicture 5 Picture 6 Secondary unit

Extension cable

(not supplied)

Picture 7

Wiring terminal

Picture 8

Picture 9

Congratulations! Herewith the mechanical installation of your gate operator is

nished. Please proceed with Programming and Basic Settings to be able to

start operation.

MOTOR 2

WHT GRN RED WHT GRN RED

MOTOR 1

BAT+

BAT-

24V

BATTERY

POW

24V

SPEC

24VDC SYNC STBY UART LIMIT-SW

E-LK

FLA

COMMANDIR SENSOREDGE24V BAT

8.2K

SAFETY EDGE

Stop

Fully Open

Partial Open

LAMP 1

FLASH LAMP

SE SE GND GNDIR3 IN3 IN2 IN1IR2 IR1

L L

AC 230V IN

CTRL GND 12V - TX RX 5V OP - CL

24V external accessories

Examples: external receiver

220-240V/50/60Hz

28V AC

EXAMPLE

S P +-

Fuse

E-LOCK / MAG LOCK

IR 1IR 2IR 3

E-LOCK: 600024

24 V CC

15W

E-LK

JP1

4321

Power

Signal

FLA

FLASH-LAMP: FLA1-LED 24V BAT: 490EV

1 1

BAT+

BAT-

24V BAT

SYNC, STBY, UART, LIMIT-SW

connectors are not used for AA units

MOTOR 2

WHT GRN RED WHT GRN RED

MOTOR 1

BAT+

BAT-

24V

BATTERY

POW

24V

SPEC

24VDC SYNC STBY UART LIMIT-SW

E-LK

FLA

COMMANDIR SENSOREDGE24V BAT

8.2K

SAFETY EDGE

Stop

Fully Open

Partial Open

LAMP 1

FLASH LAMP

SE SE GND GNDIR3 IN3 IN2 IN1IR2 IR1

L L

AC 230V IN

CTRL GND 12V - TX RX 5V OP - CL

24V external accessories

Examples: external receiver

220-240V/50/60Hz

28V AC

EXAMPLE

S P

Fuse

E-LOCK / MAG LOCK

IR 1IR 2IR 3

E-LOCK: 600024

24 V CC

15W

E-LK

JP1

4321

Power

Signal

FLA

FLASH-LAMP: FLA1-LED 24V BAT: 490EV

1 1

BAT+

BAT-

24V BAT

6. WIRING DIAGRAM

Inhaltsverzeichnis

Sprachen:

Andere MyQ Toröffner Handbücher

MyQ

MyQ CHAMBERLAIN CHLA250EVC Bedienungsanleitung

Beliebte Toröffner Handbücher anderer Marken

Elite

Elite CSW200UL Bedienungsanleitung

CAME

CAME FROG-PM4 Bedienungsanleitung

SOMFY

SOMFY FX230 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Bedienungsanleitung

Turnstiles

Turnstiles FSW 900 Bedienungsanleitung

Erreka

Erreka BUL BL33 Betriebsanleitung

Erreka

Erreka VULCAN S Bedienungsanleitung

Beninca

Beninca R1-2 WBV Bedienungsanleitung

Erreka

Erreka VULCAN D Bedienungsanleitung

Motorline professional

Motorline professional FORT Bedienungsanleitung

Beninca

Beninca BOB5024 Bedienungsanleitung

AGA

AGA GATEMASTER 900 HD Bedienungsanleitung

Chamberlain

Chamberlain MotorLift HC280ML Bedienungsanleitung

SOMFY

SOMFY Dexxo RTS Pro Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Westfalia

Westfalia 85 27 06 Bedienungsanleitung

CAME

CAME F500 Bedienungsanleitung

Extel

Extel VERA Bedienungsanleitung