Mytee HP100 Grand Prix Bedienungsanleitung

HP-100/HP-60 1

www.unoclean.com

HP-100

HP-60

Extractor

User and Parts Manual

HP-100/HP-60 2

www.unoclean.com

TABLE OF CONTENTS:

This manual is furnished with each new model. It

provides necessary operation and maintenance

instructions and an illustrated parts list.

Read this manual completely and understand the

machine before operating or servicing it.

Use the illustrated Parts List to order parts. Before

ordering parts or supplies, be sure to have your

machine model number and serial number handy.

Parts and supplies may be ordered by phone or mail

from any authorized parts and service center,

distributor or from any of the manufacturer’s

subsidiaries.

MACHINE DATA

Please fill out at time of purchase for future

reference.

Model No.: ______________________________

Purchase Date: ___________________________

Serial No.: _______________________________

SAFETY PRECAUTIONS 3

GROUNDING INSTRUCTIONS 3

SAFETY LABELS 4

MACHINE COMPONENTS 4

PRE-OPERATION 5

MACHINE SET UP 5

WHILE OPERATING 6

DRAINING RECOVERY TANK 7

MACHINE MAINTENANCE 7

DAILY MAINTENANCE 7

WEEKLY MAINTENANCE 7

STORING MACHINE 8

TROUBLESHOOTING 9

HP-100/HP-60 3

www.unoclean.com

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is

designed to clean carpet and upholstery in an indoor

environment and is not constructed for any other

use. Use only recommended cleaning solutions and

accessory tools.

All operators must read, understand and practice the

following safety precautions.

The following safety alerts symbols are used

throughout this manual as indicated in their

description:

WARNING: To warn of hazards or unsafe

practices which could result in severe personal

injury or death.

FOR SAFETY: To identify actions which must be

followed for safe operation of equipment.

The following information signal potentially

dangerous conditions to the operator or equipment:

FOR SAFETY:

1. Do not operate machine:

♦

♦♦

♦Unless trained and authorized.

♦

♦♦

♦

Unless operator manual has been read

and understood.

♦

♦♦

♦In flammable or explosive areas.

♦

♦♦

♦Unless cord is properly grounded.

♦

♦♦

♦With damaged cord or plug.

♦

♦♦

♦If not in proper operating condition.

♦

♦♦

♦In outdoor areas.

♦

♦♦

♦In standing water.

♦

♦♦

♦With the use of an extension cord.

2. Before operating machine:

♦

♦♦

♦Make sure all safety devices are in

place and operate properly.

3. When using machine:

♦

♦♦

♦Do not run machine over cord.

♦

♦♦

♦Do not pull machine by plug or cord.

♦

♦♦

♦Do not pull cord around sharp edges

or corners

♦

♦♦

♦Do not unplug by pulling on cord.

♦

♦♦

♦Do not stretch cord.

♦

♦♦

♦Do not handle plug with wet hands.

♦

♦♦

♦Keep cord away from heated surfaces.

♦

♦♦

♦Report machine damage or faulty

operation immediately to your

distributor.

♦

♦♦

♦Follow mixing and handling

instructions on chemical containers.

4. Before leaving or servicing machine:

♦

♦♦

♦Turn off machine.

♦

♦♦

♦Unplug cord from wall outlet.

5. When servicing machine:

♦

♦♦

♦Unplug cord from wall outlet.

♦Avoid moving parts.

♦

♦♦

♦Do not wear loose jackets, shirts, or

sleeves.

♦

♦♦

♦Use manufacturer supplied or

approved replacement parts.

WARNING: Hazardous Voltage. Shock or

electrocution can result. Always unplug machine

before servicing.

WARNING: Flammable materials can

caus

e an explosion or fire. Do not use flammable

materials in tank(s).

WARNING: Flammable materials or

reactive metals can cause an explosion or fire.

GROUNDING INSTRUCTIONS

Machine must be grounded. If it should

malfunction or breakdown, grounding pr

ovides a

path of least resistance for electrical shock. This

machine is equipped with a cord having an

equipment-grounding conductor and grounding

plug. The plug must be plugged into an

appropriate outlet that is properly installed in

accordance with all local code and ordinances.

Do not remove ground pin; if missing, replace

plug before use.

HP-100/HP-60 4

www.unoclean.com

SAFETY LABELS

MACHINE COMPONENTS

The safety labels appear on the machine in

the locations indicated. Replace labels if

they become damaged or cannot be read.

1. Recovery Tank

2. Solution Tank

3. Motor housing/ Base

WARNING LABEL- Located on back.

Label warns operator of safe practices of

equipment

WARNING: Flammable materials can

cause an explosion or fire. Do not use

flammable materials in tank(s). Flammable

materials or reactive metals can cause

explosion or fire.

HP-100

HP-60

HP-100/HP-60 5

www.unoclean.com

1. Carefully check carton for signs of damage.

Report damage at once to freight carrier. The

machine is shipped fully assembled and is

ready for use.

2. Open lid of solution tank. Fill solution tank

with water or approved cleaning agent.

PRE-OPERATION

1. Vacuum carpet and upholstery and remove

other debris.

2. Perform MACHINE SETUP procedures.

3. Inspect power cord for damage.

WARNING: Flammable materials can

cause an explosion or fire. Do not use flammable

solutions or materials in tank(s).

FOR SAFETY: When using machine, follow

mixing and handling instructions on chemical

containers.

ATTENTION: If using powdered cleaning

chemicals, mix prior to adding.

NOTE: Make sure the quick

disconnects snap together firmly. As

you do this, always inspect hoses for

cracks or fraying. Do not use if hoses

are damaged.

3. Attach male quick disconnect (qd) from

solution hose to female qd on front of extractor.

4. Attach other end of solution hose to

upholstery tool.

5. Attach vacuum hose to recovery tank.

6. Attach other end of vacuum hose to

upholstery tool.

MACHINE SET UP PROCEDURES

HP-100/HP-60 6

www.unoclean.com

FOR SAFETY:

Do not operate machine unless

cord is properly grounded.

FOR SAFETY: Do not operate machine with

the use of an extension cord.

5. Begin cleaning

7. Plug machine’s cord into a grounded wall outlet.

1. Work away from outlet and power cord to

prevent cord damage.

2. Use a recommended foam control solution in

the recovery tank to prevent vacuum motor

damage. Periodically check for excessive foam

buildup in solution tank, and recovery tank.

3. To clean heavily soiled areas, repeat cleaning

path from different direction.

4. When ball float shuts off vacuum, it is time to

empty the dirty water from the recovery tank, and

refill solution tank.

5. After cleaning, relieve water pressure from tool

before disconnecting hose. Squeeze trigger for

five seconds after turning main power switch off.

WHILE OPERATING

2. Prime the pump by pulling up on tool lever

to release air in the line. Hold lever until you

have a steady flow of water coming out of the

tool.

3. Once pump is primed and you have

pressure in the solution line, turn on

heater switch(s) and wait a few minutes

for water to heat up.

1. After you have completed the

machine setup procedures, turn pump

switch on.

MACHINE OPERATION

4. Turn on vacuum power

NOTE: When cleaning upholstery, always

check cleaning instructions sewn in

furniture by manufacturer.

HP-100/HP-60 7

www.unoclean.com

To keep machine in good working condition,

simply follow machine’s daily and weekly

maintenance procedures. Check valves and relief

valves should be replaced annually.

FOR SAFETY: When servicing machine,

unplug cord from wall outlet.

MACHINE MAINTENENCE

2. Inspect vacuum hoses for holes and loose cuffs.

3. Inspect spray pattern for clogging. If clogged,

remove spray tips and soak them in a

recommended liquid neutralizer for up to six

hours. To remove spray tip, twist spray tip body

counter-clockwise.

4. Lubricate wheels with water resistant oil.

5. Inspect machine for water leaks and loose

hardware.

6. Remove float shut-off screen from recovery

tank and clean.

NOTE: The float shut off screen is not glued on.

Simply pull it off.

WEEKLY MAINTENANCE

(EVERY 20 HOURS OF OPERATION)

1. Flush solution system with Mytee system

maintainer to dissolve normal chemical buildup.

a. Pour 7.5L (2 gal) of hot water 60°C (140°F)

into solution tank. Add Mytee system

maintainer according to mixing instructions

on bottle

b. Operate machine for one minute.

c. Shut off machine and allow

remaining solution to break down

chemical buildup overnight.

d. Next day, spray out remaining

solution and flush system with

11L (3gal) of clean water.

FOR SAFETY: When using machine,

follow mixing and handling instructions on

chemical containers.

1. Empty and rinse out solution tank thoroughly.

2. Wipe off power cord and check for damage, replace if

necessary. Coil cord neatly after use.

3. Clean machine with an all purpose cleaner and damp

cloth.

DAILY MAINTENANCE

3.Attach 45º-drain elbow to dump valve

and lift up drain valve lever to empty

solution tank.

FOR SAFETY: When servicing machine,

unplug cord from wall outlet.

1. Turn machine off and unplug power

cord.

2. Remove solution & vacuum hose

DRAINING RECOVERY TANK

45º Elbow

HP-100/HP-60 8

www.unoclean.com

ATTENTION: Do not expose to rain. Store indoors.

ATTENTION: If storing machine in freezing temperatures,

be sure that machine and solution system are completely

drained and dry.

SYMPTOM: UNIT WILL NOT TURN ON:

PROBLEM: Not plugged in.

SOLUTION: Plug machine in proper outlet.

PROBLEM: Circuit breaker has popped.

SOLUTION: Reset circuit breaker. Make sure no other items are running on the same circuit as

machine. Outlet must be a 20-amp circuit.

SYMPTOM: PUMP IS NOT RUNNING PROPERLY:

PROBLEM: Quick disconnects are not completely locked together.

SOLUTION: Snap quick disconnects firmly together.

PROBLEM: The solution tank is empty.

SOLUTION: Fill the solution tank up with a premixed liquid detergent.

PROBLEM: Jet on upholstery tool is clogged.

SOLUTION: Clean jet with soft wire brush or remove jet and flush clean.

PROBLEM: Filters are clogged.

SOLUTION: Remove filters and rinse clean with water.

PROBLEM: Heater is blocked with hard water deposits.

SOLUTION: Flush out heaters with Mytee Products, Inc. system maintainer solution.

STORING MACHINE

Before storing machine, be certain to completely drain and

rinse tanks of all water and solution.

2. Drain and dry the vacuum hose as well, using the drain

hose provided

3. Store machine in a dry area in the upright position.

4. Open recovery tank cover to promote air circulation

TROUBLESHOOTING

HP-100/HP-60 9

www.unoclean.com

PROBLEM: Brass check valve is stuck.

SOLUTION: Replace with new check valve.

SYMPTOM: VACUUM MOTOR IS NOT WORKING PROPERLY:

PROBLEM: Hose not connected tightly to upholstery tool or machine.

SOLUTION: Connect hose tightly.

PROBLEM: Drain valve is not shut completely.

SOLUTION: Close drain valve completely.

PROBLEM: Vacuum tank lid is not on tightly.

SOLUTION: Secure the vacuum tank tightly.

PROBLEM: Ball float is shut off.

SOLUTION: Empty the vacuum tank of all wastewater.

PROBLEM: Water is coming out of vacuum motor.

SOLUTION: Use a low foaming detergent.

PROBLEM: Upholstery tool or wand is clogged with hair, carpet fibers and or debris.

SOLUTION: Clean upholstery tool or floor wand jets.

PROBLEM: Ball float is not installed correctly.

SOLUTION: Make sure that ball float is firmly installed on the elbow.

HP-100/HP-60 10

www.unoclean.com

DESCRIPTION

WHERE USED

PART

NUMBER

Vacuum motor

3 stage 115v

HP100

HP60

C302

Quick connect

Female ¼”

HP100

HP60

B102

Quick connect

Male ¼”

HP100

HP60

B101

Element heater

600 watt

HP100

HP60

E571

Switch, 2 position

HP100

HP60

E592

System

maintainer,

12 quarts per case

HP100

HP60

3601

Andere Handbücher für HP100 Grand Prix

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mytee Bodenreinigungsmaschine Handbücher

Mytee

Mytee 7000DX Flood Hog Bedienungsanleitung

Mytee

Mytee Contractor's Special 2000CS Firmware-Update

Mytee

Mytee Prep Center S 80-120 Bedienungsanleitung

Mytee

Mytee ECO-13 Bedienungsanleitung

Mytee

Mytee ECO14-PRO Bedienungsanleitung

Mytee

Mytee 1000DX-200 Speedster Bedienungsanleitung

Mytee

Mytee Breeze BZ-102LX Bedienungsanleitung

Mytee

Mytee ECO-15-24VDC Bedienungsanleitung

Mytee

Mytee 8070 Lite Bedienungsanleitung

Mytee

Mytee 8070 Lite Bedienungsanleitung

Mytee

Mytee Speedster 1000DX Installations- und Betriebsanleitung

Mytee

Mytee 1000DX-200 Speedster Bedienungsanleitung

Mytee

Mytee Speedster LTD Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Mytee

Mytee Spyder HP60 Bedienungsanleitung

Mytee

Mytee 1003DX Speedster Installations- und Betriebsanleitung

Mytee

Mytee T-REX Montageanleitung

Mytee

Mytee Spyder HP60 Bedienungsanleitung

Mytee

Mytee 8070 Installations- und Betriebsanleitung

Mytee

Mytee Spinner 8901 Bedienungsanleitung

Mytee

Mytee Flood Hog 7000SX Bedienungsanleitung

Mytee

Mytee Grand Prix HP120 Bedienungsanleitung

Mytee

Mytee Speedster LTD3 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung