NANO 3 series Bedienungsanleitung
HEATLESS DESICCANT AIR DRYER
SERIES 3 AIR DRYER USER GUIDE
Page 2
nano purication solutions.
17-110-0140
1. General information 3
1.1. Document introduction 3
1.2. North America Support Details | Manufacturers details 3
1.3. Warranty Guidelines 4
1.4. Packaging 4
2. General safety 5
2.1. Intended Use 5
2.2. Personnel 5
2.3. Safe Handling 5
3. Technical Description 6
4. TechnicalSpecication 6
5. Product Contents 7
6. Unpacking Guide 8
7. Product Dimensions 9
8. Equipment Overview 10
9. System Layout 11
10. Mechanical Installation 12
11. Electrical Installation 13
12. Dryer Operation 14
12.1. Dryer Remote Control 14
12.2. Dryer Start up 15
12.3. Monitoring Dryer Performance 16
12.4. Shutdown Procedure 16
13. Maintenance 17
13.1. Maintenance guidelines 17
13.2. Cleaning 17
13.3. Daily checks 17
14. Servicing 17
14.1. Guidelines 18
14.2. Procedures 19
14.3. Additional Kits 19
15. Troubleshooting 20
Contents Page
Page 317-110-0140
1. General Information
This manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine readable form without prior consent
in writing from It may not be distributed through the internet or computer bulletin
1.1 Document Introduction
solutions compressed air dryer. The procedures illustrated in this document are only to be performed by
authorized personnel. For further information regarding the procedures outlined in this document contact nano
Read this document carefully before attempting to install or operate the dryer. This document should be
permanently available at the dryer installation site and be kept in an easily accessible place alongside the
dryer.
©2014 nano solutions.
Product: Series 3 Desiccant Air Dryer
Document number: 17-110-0140
Issue: 003
NOTES: highlight important sections of information where particular care and attention should
be paid.
CAUTIONS: indicate any situation or operation that may result in potential damage to
the product, injury to the user, or render the product unsafe.
Annotations:
1.2 Support
For parts and technical support please contact:
solutions
11330 Vanstory Drive
Huntersville, NC 28078
USA
Telephone: (704) 897-2182
Fax: (704) 897-2183
Internet: www.n-psi.com
E-mail: [email protected]
Manufactured in the UK
in an ISO 9001 certified facility
Page 4
nano purication solutions.
17-110-0140
1.3 Warranty Guidelines
All products are supplied with a 5 year manufacturer’s warranty from the date of purchase,
when purchased with an ES (Energy Saving) system and installed and maintained in
accordance with the manufacturers guidelines. Only genuine service parts should be used
and no modications made. For further information please contact nano purication solutions.
1.4 Packaging
All products are securely packaged in a specically designed wooden packing box. The dryer
will be held in a horizontal position by wooden struts; using straps to secure the product to
the box base. The box top cover can be removed by removing the 4 xing screws and lifting
off in one piece.
The support packing box permits longitudinal stacking; however the central section
of the packing box should not be considered load bearing.
Damage to Packaging
• Check immediately to establish whether damage has occurred to the external packaging
and if the damage extends to the product inside.
• If there is damage to a product, contact the relevant supplier immediately.
In no circumstances must a damaged product be used in operation. Using damaged
products can lead to irreparable functional faults or cause serious physical harm.
Page 5
17-110-0140
2. General safety
For your own safety, when carrying out work on this product, all relevant
national safety regulations must be complied with relating to pressurized
and electrical systems.
2.1. Intended use of the Product
The dryer is exclusively intended for the treatment of compressed air, which is free from
bulk water, oil and solid matter constituents.
The product should be located within a building and protected. The dryer must be operated
only in accordance with the data on the rating plate. Any operations that do not comply with
those stated on the product rating plate will render the warranty void.
This product is only designed to operate at pressures of between 58 - 145
psig (4 - 10 barg).
It is not suitable for pressures in excess of 145 psig (10 barg).
No modications must be made to the product. Any modications may reduce the
operational safety of the product and invalidate the manufacturer’s warranty. This could
potentially result in damage to the product and serious personal injury.
2.2. Personnel
Only authorized, competent and trained personnel are permitted to work on this product.
This user guide is intended solely for such personnel and is to be used only as a reference;
it should not be used to replace conventional training.
2.3. Safe Handling
Please ensure the relevant safe engineering practices and handling procedures are
employed when handling, installing and operating this product. Ensure that the equipment
is depressurized and electically isolated prior to carrying out any of the scheduled
maintenance instructions specied within this user guide.
A suitable lifting aid must be used to minimize the risk of physical injury or
damage to the product.
In no circumstances must a damaged product be used in operation. Using
damaged products can lead to irreparable functional faults or cause serious
physical harm.
Page 6
nano purication solutions.
17-110-0140
3. Technical Description
The n-psi dryer uses the pressure swing adsorption principle of drying compressed air,
utilizing two identical columns each containing a hygroscopic desiccant bed.
• Inlet ltration removes water, oil aerosols and particles (Inlet ltration supplied
separately).
• Wet air enters the dryer through the inlet valve and is directed into one of the columns.
• Each column contains a densely lled desiccant bed.
• Air then passes through the desiccant bed where any remaining moisture is adsorbed.
• Simultaneously, a small amount of dry ltered air is counter owed down through
the other desiccant bed and exhausted to atmosphere, removing the moisture and
regenerating the desiccant bed.
• The dryer controller periodically switches columns after top end repressurization;
ensuring a continuous supply of dry air at constant pressure. The dryer can also be
controlled using a Zero Volt signal from the compressor. This energy saving mode
senses when the compressor is switched off and stops the dryer operation until the
compressor restarts.
• The dry air passes out through the nal particulate lter (<1micron/ISO8573.1 Class 2).
Specication
ISO 8573 - 2:2001 Quality Classes Class 2: Water: -40°F (-40°C) PDP / Class 2: Dirt: 1µm
Optional Class 1 (-100°F) and Class 3 (0°F)
Minimum working pressure 58 psig (4 bar)
Maximum working pressure 145 psig (10 bar) - higher pressures available upon request
Power Supply 100 - 240v AC / 50 - 60Hz
Minimum inlet temperature 34.7°F (1.5°C)
Maximum inlet temperature 122°F (50°C)
Ambient Temperature 34-122°F (1-50°C)
IP Rating IP54 / NEMA 3
Power 38W
4. TechnicalSpecication
• Flow rate based on air inlet pressure of 100 psig (7.0 barg) and temperature of 95°F
(35°C).
• For dryer performance at other inlet conditions or -100°F (-70°C) dewpoint
• All dryers should be proceeded by a coalescing lter regardless of oil or oil free
applications, a nano M01 grade coalescing lter must be installed on the inlet to the
dryer.
Page 7
17-110-0140
5. Product Contents
1. Series 3 Compressed Air Dryer
2. Documentation
• 1 x User Guide
• 1 x Declaration of Conformity
3. Packaging
• 1 x Dryer support base and box cover
Figure 1: Contents Layout
Page 8
nano purication solutions.
17-110-0140
6. Unpacking Guide
The dryer is supplied in a wooden crate. It is recommended that the crate be moved into
position using a forklift truck or pallet truck. Remove the dryer from the wooden crate using
an overhead crane. Use the following illustrations for correct guidance on safe handling and
lifting techniques.
• Cut packaging straps rst, before lifting.
21
3
5 6
4
Ensurethattheexternalsilencers/mufersareremovedbeforeattempting
toliftthepurier.
Page 9
17-110-0140
7. Product Dimensions
MODEL
CONNECTION
A
ins
(mm)
B
ins
(mm)
C
ins
(mm)
D
ins
(mm)
E
ins
(mm)
WEIGHT
lbs
(KG)
NDL - 2110 2” NPT 26
(678)
15
(382)
50
(1289)
16
(400)
14
(360)
366
(166)
NDL - 2120 2” NPT 26
(678)
15
(382)
60
(1538)
16
(400)
14
(360)
441
(200)
NDL - 2130 2” NPT 26
(678)
15
(382)
73
(1889)
16
(400)
14
(360)
547
(248)
NDL - 3130 2” NPT 31
(781)
21.6
(550)
73
(1889)
16
(400)
14
(360)
778
(353)
NDL - 4130 2.5” NPT 38
(949)
28
(718)
73
(1889)
16
(400)
14
(360)
1010
(548)
NDL - 6120 2.5” NPT 51
(1285)
41.5
(1054)
60
(1538)
16
(400)
14
(360)
1155
(524)
NDL - 6130 2.5” NPT 51
(1285)
41.5
(1054)
73
(1889)
16
(400)
14
(360)
1473
(668)
A
B
D
E
C
Page 10
nano purication solutions.
17-110-0140
8. Equipment Overview
1
2
3
4
9
8
7
5
6
Controller Display UnitDryer Top Cover
Front Shroud
Air Outlet Air Inlet
Dryer Column
1
5 6
3
2
4
External Silencers/Mufers Mains Power
7 8
Remote Stop/Start Control
(if required)
9
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Andere NANO Luftentfeuchter Handbücher
NANO
NANO Flux Twin Bedienungsanleitung
NANO
NANO NXC Series Bedienungsanleitung
NANO
NANO D-Series Handbuch
NANO
NANO NDL-2110 Handbuch
NANO
NANO D-Series Handbuch
NANO
NANO NXC Series Bedienungsanleitung
NANO
NANO NRC0020-0200 UL Betriebsanleitung
NANO
NANO D1 Series Handbuch
NANO
NANO D3 Bedienungsanleitung
NANO
NANO D2 Bedienungsanleitung
