NANO Flux Twin Bedienungsanleitung

Please read all the way through the instructions to familiarise yourself with the process

before you start assembly.

Pay close attention to the alignment of all the parts in the diagrams.

Maintenance and operation instructions can be found at the end of this document.

Nano Flux Twin Assembly instructions page 1 of 27

Base

1X1X

Flywheel

1X1X

Connecting rod

2X2X

Burner body

1X1X

Foot bracket

1X1X

Foot

1X1X

Front plate

1X1X

Bearing bracket

1X1X

Nano Flux Twin Assembly instructions page 2 of 27

Burner cap

2X2X

M2x10 screw

4X4X

M2X8 screw

10X10X

M2x6 screw

10X10X

M2x8 countersunk

screw

2X2X

Crank bush

2X2X

10mm O ring

2X2X

13mm O ring

6X6X

Rubber feet

4X4X

ylinder

2X2X

Tube

2X2X

Wick

2X2X

Piston

2X2X

Fin block

2X2X

Nano Flux Twin Assembly instructions page 3 of 27

Screw 4x M2x8 screws through the

foot bracket into the foot and

tighten.

Nano Flux Twin Assembly instructions page 4 of 27

Fit 2x 13mm O rings into the grooves in the first fin

block.

This step can be quite tricky, once you have the

first O ring nearly all the way in by hand you can

finish with the end of the torx driver and then

proceed to the second O ring.

Repeat for the second fin block.

Nano Flux Twin Assembly instructions page 5 of 27

Align the flat sections on the fin blocks upwards

and push them into the hole in the packing tray.

This will hold them still while you perform the next

couple of assembly stages.

Flat section

Nano Flux Twin Assembly instructions page 6 of 27

Screw 4x M2x10 screws and 4x M2x6 screws through

the foot bracket into the fin block.

Screw the screws down until they all lightly touch the

foot bracket, then lightly tighten all the screws.

As you lightly tighten the screws the flat sections on the

fin blocks will be pulled into alignment with the foot

bracket.

When all the screws are lightly tightened you can fully

tighten them all.

M2x10 this end

4X4X4X4X4X

M2x6 this end

4X4X4X4X4X

Nano Flux Twin Assembly instructions page 7 of 27

Dimple

Countersink

Align the base with the

countersinks and dimples upwards

and screw 4x M2x8 screws through

the base into the foot and tighten.

The screws will tighten halfway into

the countersinks.

Nano Flux Twin Assembly instructions page 8 of 27

Peel the backing off the 4x rubber

feet and stick over the dimples.

Remove from the packing tray

when completed.

Nano Flux Twin Assembly instructions page 9 of 27

Align the front plate with the

countersinks outwards and screw 2x

M2x8 countersunk screws through the

front plate into the bearing bracket

and tighten.

Note: the middle hole in the bearing

bracket is not used on this engine.

Countersink

Not used

Nano Flux Twin Assembly instructions page 10 of 27

Andere NANO Luftentfeuchter Handbücher

NANO

NANO D2 Bedienungsanleitung

NANO

NANO D-Series Handbuch

NANO

NANO NXC Series Bedienungsanleitung

NANO

NANO NDL-2110 Handbuch

NANO

NANO NRC0020-0200 UL Betriebsanleitung

NANO

NANO D1 Series Handbuch

NANO

NANO 3 series Bedienungsanleitung

NANO

NANO D-Series Handbuch

NANO

NANO D3 Bedienungsanleitung

NANO

NANO NXC Series Bedienungsanleitung

Beliebte Luftentfeuchter Handbücher anderer Marken

Daitsu

Daitsu CD031IU-DFA Bedienungsanleitung

Fehom

Fehom PDGT701BE Bedienungsanleitung

Hitachi

Hitachi RD-190GX Bedienungsanleitung

Westpoint

Westpoint MDF1-30AE Bedienungsanleitung

SOLIS

SOLIS easy dry compact Bedienungsanleitung

Sinclair

Sinclair R-9112 Bedienungsanleitung

Kenmore

Kenmore 580.54701 Bedienungsanleitung

Demargo

Demargo DM828NF Bedienungsanleitung

Altrad Lescha

Altrad Lescha LDH 600 Bedienungsanleitung

BOMANN

BOMANN LE 1150 CB Bedienungsanleitung

SPT

SPT SD-46 Bedienungsanleitung

REMKO

REMKO SLN 40 Bedienungsanleitung

Haier

Haier HD458 Bedienungsanleitung

Logik

Logik L20DHW12 Bedienungsanleitung

Frigidaire

Frigidaire FDR30S1 - 30 Pint Capacity Dehumidifier Kurzanleitung

Blitz

Blitz HHD Series Bedienungsanleitung

Prem-I-Air

Prem-I-Air PD14DEN Bedienungsanleitung

Klarstein

Klarstein 10032042 Bedienungsanleitung