National Instruments IMAQ D100DAL Bedienungsanleitung

IMAQ ™is a trademark of National Instruments Corporation. Product and company names mentioned herein are trademarks or trade names of their

respective companies.

INSTALLATION GUIDE

IMAQ D100DAL CABLE

This guide describes how to attach an IMAQ D100DAL cable to your

image acquisition (IMAQ) device and a DALSA camera. This guide

discusses two possible DALSA camera configurations: one in which the

camera has a combined control/power connector receptacle and one in

which the control connector receptacle and power connector receptacle are

separate.

You can use an IMAQ D100DAL cable to connect your IMAQ device to

your DALSA video camera and four trigger channels. Refer to your IMAQ

device documentation for more detailed information on these external

trigger signals.

Note Your DALSA camera cable receptacles may appear different from those

illustrated in this guide. Refer to the National Instruments Web site,

http://www.natinst.com/imaq, for the latest information on using DALSA cameras

with your IMAQ device.

What You Need to Get Started

To install your IMAQ D100DAL cable, you will need the following:

❑IMAQ D100DAL cable

❑IMAQ D100DAL Cable Installation Guide

❑Your IMAQ device and documentation

❑Your computer

❑Your DALSA camera

❑IMAQ D2504 cable and documentation (optional)

❑BNC cables for trigger signal connection (optional)

❑Trigger signal sources (optional)

IMAQ D100DAL Cable Installation Guide 2 www.natinst.com

Installation

Follow these steps to connect an IMAQ D100DAL cable to a camera with

a combined control/power connector receptacle, as illustrated in Figure 1.

1. Insert the 100-pin SCSI-type connector end of the IMAQ D100DAL

cable into the external 100-pin SCSI-type receptacle of your IMAQ

device, ensuring correct polarity. Tighten the thumbscrews as

necessary.

2. Depending on yourcamera, insert the OS1 or OS1/2 camera connector

of the IMAQ D100DAL cable into your camera’s corresponding

receptacle, ensuring correct polarity.

3. Insert the OS2 or OS3/4 camera connector of the IMAQ D100DAL

cable into your camera’s corresponding receptacle, ensuring correct

polarity.

Note Some DALSA cameras have only an OS1 or OS1/2 receptacle. With such cameras,

you do not need to connect anything to the OS2 or OS3/4 connector.

4. Insert the IMAQ D100DAL control/power connector into the camera’s

corresponding receptacle, ensuring correct polarity.

5. Insert the IMAQ D100DAL cable’s power supply connector into the

camera’s external power supply receptacle.

©National Instruments Corporation 3 IMAQ D100DAL Cable Installation Guide

Figure 1. IMAQ D100DAL Cable With Camera Power Supply Connector

1 Trigger Connector

2 IMAQ D2504 Cable

3 OS1 or OS1/2

Connector

4 OS2 or OS3/4

Connector

5 Control/Power

Connector

6 DALSA Camera

7 Camera Power Supply

8 Power Supply

Connector

9 IMAQ D100DAL cable

10 SCSI-Type Connector

11 IMAQ Device

To Triggers

IMAQ D100DAL Cable Installation Guide 4 www.natinst.com

Follow these steps to connect an IMAQ D100DAL cable to a camera with

separate control connector and power connector receptacles, as illustrated

in Figure 2.

1. Insert the 100-pin SCSI-type connector end of the IMAQ D100DAL

cable into the external 100-pin SCSI-type receptacle of your IMAQ

device, ensuring correct polarity. Tighten the thumbscrews as

necessary.

2. Insert the OS1/2 camera connector of the IMAQ D100DAL cable into

your camera’s corresponding receptacle, ensuring correct polarity.

3. Insert the OS3/4 camera connector of the IMAQ D100DAL cable into

your camera’s corresponding receptacle, ensuring correct polarity.

Note Some DALSA cameras have only an OS1/2 receptacle. With such cameras, you do

not need to connect anything to the OS3/4 connector.

4. Insert the IMAQ D100DAL control connector into the camera’s

corresponding receptacle, ensuring correct polarity.

Figure 2. IMAQ D100DAL Cable Without Camera Power Supply Connector

1 Trigger Connector

2 IMAQ D2504 Cable

3 OS1/2 Connector

4 OS3/4 Connector

5 Control Connector

6 DALSA Camera

7 Power Connector

8 IMAQ D100DAL cable 9 SCSI-Type Connector

10 IMAQ Device

To Triggers

©National Instruments Corporation 5 IMAQ D100DAL Cable Installation Guide

Triggering

If you plan to connect external trigger signals to your IMAQ device, you

can use either the IMAQ D2504 cable or your own trigger interface cable.

If building your own cable, see Figure 3 for pin-out information. For more

information on the D2504 cable, see the IMAQ 2504 Cable Installation

Guide.

To connect external trigger signals to your IMAQ device, insert the trigger

interface cable into the trigger connector of the IMAQ D100DAL cable,

ensuring correct polarity. Tighten the thumbscrews as necessary.

Figure 3. D100DAL Cable Trigger Connector Pin Assignments

TRIGGER0

TRIGGER1

TRIGGER2

TRIGGER3

Unused

GND

Unused

GND

Unused

Reserved

Unused

Inhaltsverzeichnis

Andere National Instruments Kabel und Steckverbinder Handbücher

National Instruments

National Instruments NI SCB-68A Bedienungsanleitung

National Instruments

National Instruments GMCT20 Bedienungsanleitung

National Instruments

National Instruments CB-27 Bedienungsanleitung

National Instruments

National Instruments 9212 Handbuch

National Instruments

National Instruments SH6850 Bedienungsanleitung

National Instruments

National Instruments BNC-2090A Bedienungsanleitung

National Instruments

National Instruments NI-XNET CAN HS/FD Bedienungsanleitung

National Instruments

National Instruments IMAQ A8014 Bedienungsanleitung

National Instruments

National Instruments PXI-1031DC Bedienungsanleitung

National Instruments

National Instruments IMAQ A2514 Bedienungsanleitung

National Instruments

National Instruments BNC-2121 Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments SH160DIN-4XDB50F-2A Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments SCXI-1345 Bedienungsanleitung

National Instruments

National Instruments SCXI-1342 PC-LPM-16 Bedienungsanleitung

National Instruments

National Instruments LFH200 Bedienungsanleitung

National Instruments

National Instruments SCXI-1353 Bedienungsanleitung

National Instruments

National Instruments CB-50 Bedienungsanleitung

National Instruments

National Instruments BNC-2120 Bedienungsanleitung

National Instruments

National Instruments IMAQ D6826 Bedienungsanleitung

National Instruments

National Instruments SCB-19 Bedienungsanleitung

National Instruments

National Instruments IMAQ A8020 Bedienungsanleitung

National Instruments

National Instruments IMAQ A8055 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung